Main
Page
Contents
Safety ..................................................................... 1
General Information ................................................3
External Connection ..............................................12
Options ................................................................ 52
Programming and Set-Up ...................................... 59
Page
Page
Safety
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
Symbols used in this manua l
User Safety
Page
990-2440 AIS 5000 400V Installation Manual 4
Site Requirements
Receiving and inspecting the UPS
Type label. Copy type label data (serial number) to label copy below for easy identification of the
system. The type label is placed on the inside of the UPS front door.
Moving the equipment to site:
Page
Air filter sizes
Enclosure dimensions and footprint
Enclosure dimensions.
990-2440 AIS 5000 400V Installation Manual 9
Footprint.
Top and bottom view of 1030kVA UPS:
10 AIS 5000 400V Installation Manual 990-2440
Top and bottom view of 4060kVA UPS:
990-2440 AIS 5000 400V Installation Manual 11
Top and bottom view of 80100kVA UPS:
12 AIS 5000 400V Installation Manual 990-2440
External Connection
Connecting the UPS
Use 1.5 mm CU conductors only.
Note
External connection board
Page
1. Open UPS front door. 2. Remove cover from the input/output section.
Access to Input/Output section
Page
990-2440 AIS 5000 400V Installation Manual 17
Connecting cables
X001 Mains Input (L1, L2, L3) X090 Bypass Input L1, L2, L3, N)
Q004 Battery (+, )
Input/Output section 1030 kVA
18 AIS 5000 400V Installation Manual 990-2440
X00 1 Mains Input (L1, L2, L3) X090 Bypass Input (L1, L2, L3, N)
Q00 4 Battery (+, )
Input/Output section 4060 kVA
990-2440 AIS 5000 400V Installation Manual 19
X001 Mains Input (L1, L2, L3) X090 Bypass Input (L1, L2, L3, N)
Q004 Battery (+, )
Input/Output section 80100 kVA
Grounding
The UPS input / bypass input is 4-Wire + Ground.
Page
Communication interface ports
Overview of Communicatio n interface
COM INTERFACE
COM PORT
10kVA 400V UPS
IS10KH
Page
Page
Page
20kVA 400V UPS
IS20KH
Page
Page
Page
30kVA 400V UPS
IS30KH
Page
Page
Page
40kVA 400V UPS
IS40KH
Page
Page
Page
60kVA 400V UPS
IS60KH
Page
Page
Page
80kVA 400V UPS
IS80KH
Page
Page
Page
100kVA 400V UPS
IS100KH
Page
Page
Page
Page
Page
Mounting the drip shield
Options - IP32 Drip Shield
990-2440 AIS 5000 400V Installation Manual 55
Drip shield sizes
IP32 for 10 30 kVA and 80 100 kVA UPS IP32 for Battery Enclosure
IP32 for 40 60 kVA UPS
56 AIS 5000 400V Installation Manual 990-2440
Relay Board
K012 K013 K014 K015 K016
ALARM POSITION
K001 K002 K003 K004 K005 K006
****************
*
Message:
*********
Communication Cards
Cards and slots
Programming and Set-Up
Display
Display introduction
Display functions
Programming and Set-Up - Display
990-2440 AIS 5000 400V Installation Manual 61
Display messages
Mains = Utility
Programming the UPS
User stack
Parameter Comments
Page
Page
Page
Page
Settings for redundant systems
Page
Setting stack
Page
Operation Modes
Operation mode descriptions:
Normal to Bypass Operation
Bypass to Normal Operation
Normal to Manual Bypass Operation
Programming and Set-Up - Operation Modes
Manual Bypass to Normal Operation (including start up procedure)
The load is now supported by the UP S.
Page
*990-2440*
APC Worldwide Customer Support
990-2440 09/2005