Emergency Power Off EPO | American Power Conversion AIS 5000

External Connection - Connecting the UPS

Emergency Power Off (EPO)

The UPS is equipped with and EPO input (X006) on the external connection board (part of the low- voltage section). The battery breaker is equipped with a shunt trip function (X061: 3, 4).

Communication interface

Shunt Trip function (120Vac)

The 3-port communication interface (located in the low voltage section) is used when an interaction between UPS and an electrical device has to be established. The main purpose is to ensure a controlled shut-down of the device in case of failures in the mains power supply.

990-2440

AIS 5000 400V Installation Manual

21

Image 27

American Power Conversion AIS 5000 manual Emergency Power Off EPO, Communication interface

Contents

AIS Page Contents Options Operation Modes Page Symbols used in this manual Safety Disconnect all sources of AC and DC power User Safety About this manual General Information Receiving and inspecting the UPS Site Requirements Moving the equipment to site Fitting the air filter Air Filter Air filter sizes Enclosure dimensions Enclosure dimensions and footprint Top and bottom view of 10-30kVA UPS Top and bottom view of 40-60kVA UPS Top and bottom view of 80-100kVA UPS External connection board Connecting the UPS  UPS Feet  Conduit Box  Front of Conduit Box Installing Conduit Boxes Input Conduit Output/Bypass Battery Alarm Conduit Access to Input/Output section Low-voltage section cover Communication Interface, EPO Connecting cables Input/Output -60 kVA Input/Output -100 kVA X090 Grounding Communication interface Emergency Power Off EPO COM-PORT Communication interface ports Overview of Communication interface COM Interface 10kVA 400V UPS Max. Discharge Current a 46 a Nominal Voltage 240 Approvals IEC 62040/EN 50091 Class A, VFI-SS-112 Emergency Power Off EPO Yes Options Max 39.4 a Mains Voltage 400 V 3 Wire + G Nom 19.88 kW 33.79 aVoltage 400 V 3 Wire + N + G Nominal Current 28.9 a 20kVA 400V UPS Max. Discharge Current a 91 a External Connection 20kVA 400V UPS Options Max 59.9 a Mains Voltage 400 V 3 Wire + G Nom 28.35 kW 47.86 aVoltage 400 V 3 Wire + N + G Nominal current 43.3 a 30kVA 400V UPS Max. Discharge Current a 135 a External Connection 30kVA 400V UPS Options Max 77.8 a Mains Voltage 400 V 3 Wire + G Nom 36.9 kW 61.93 aVoltage 400 V 3 Wire + N + G Nominal current 57.7 a 40kVA 400V UPS Max. Discharge Current a 179 External Connection 40kVA 400V UPS Options Max 117 a Mains Voltage 400 V 3 Wire + G Nom 54.42 kW 90.08 aVoltage 400 V 3 Wire + N + G Nominal current 86.6 a 60kVA 400V UPS Max. Discharge Current a 266 External Connection 60kVA 400V UPS Options Max 152.8 a Mains Voltage 400 V 3 Wire + G Nom 72.33 kW 118.23 aVoltage 400 V 3 Wire + N + G Nominal current 115.5 a 80kVA 400V UPS Max. Discharge Current a 353 External Connection 80kVA 400V UPS Options 100kVA 400V UPS Max. Discharge Current a 442 External Connection 100kVA 400V UPS Options Options IP32 Drip Shield Mounting the drip shield Drip shield sizes Message Relay Board Message Cards and slots Communication Cards Display introduction Display Display functions Display messages Programming the UPS User stackKeys Until the display shows Bypass Operation Push Cursor keys Programming and Set-Up Programming the UPS Auto Boost Charge OFF Battery Capacity Test ??? Battery Monitor Alarm Settings for redundant systems Enter new time HH.MM.SS Setting stack Minutes10 kVA 20 kVA 30 kVA 40 kVA 60 kVA 80 kVA 100 kVA How to change factory settings Operation Modes Operation mode descriptions Normal to Bypass Operation Bypass to Normal OperationPress Normal to Manual Bypass Operation Load is now supported by the UPS Page 990-2440