American Power Conversion AIS 5000 Mounting the drip shield

Options - IP32 Drip Shield

54 AIS 5000 400V Installation Manual 990-2440

Mounting the drip shield

x 4 x 4

Remove protection foil before assembly!

(not shown on illustration)

x 4

Remove the 4 bolts from UPS drip shield and mount the 4 stand-offs.

Reuse bolts from UPS roof to attach drip shield

Mount sides on drip shield









Contents

Main Page Contents Safety ..................................................................... 1 General Information ................................................3 External Connection ..............................................12 Options ................................................................ 52 Programming and Set-Up ...................................... 59 Page Page Safety IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Symbols used in this manua l User Safety Page 990-2440 AIS 5000 400V Installation Manual 4 Site Requirements Receiving and inspecting the UPS Type label. Copy type label data (serial number) to label copy below for easy identification of the system. The type label is placed on the inside of the UPS front door. Moving the equipment to site: Page Air filter sizes Enclosure dimensions and footprint Enclosure dimensions. 990-2440 AIS 5000 400V Installation Manual 9 Footprint. Top and bottom view of 1030kVA UPS: 10 AIS 5000 400V Installation Manual 990-2440 Top and bottom view of 4060kVA UPS: 990-2440 AIS 5000 400V Installation Manual 11 Top and bottom view of 80100kVA UPS: 12 AIS 5000 400V Installation Manual 990-2440 External Connection Connecting the UPS Use 1.5 mm CU conductors only. Note External connection board Page 1. Open UPS front door. 2. Remove cover from the input/output section. Access to Input/Output section Page 990-2440 AIS 5000 400V Installation Manual 17 Connecting cables X001 Mains Input (L1, L2, L3) X090 Bypass Input L1, L2, L3, N) Q004 Battery (+, ) Input/Output section 1030 kVA 18 AIS 5000 400V Installation Manual 990-2440 X00 1 Mains Input (L1, L2, L3) X090 Bypass Input (L1, L2, L3, N) Q00 4 Battery (+, ) Input/Output section 4060 kVA 990-2440 AIS 5000 400V Installation Manual 19 X001 Mains Input (L1, L2, L3) X090 Bypass Input (L1, L2, L3, N) Q004 Battery (+, ) Input/Output section 80100 kVA Grounding The UPS input / bypass input is 4-Wire + Ground. Page Communication interface ports Overview of Communicatio n interface COM INTERFACE COM PORT 10kVA 400V UPS IS10KH Page Page Page 20kVA 400V UPS IS20KH Page Page Page 30kVA 400V UPS IS30KH Page Page Page 40kVA 400V UPS IS40KH Page Page Page 60kVA 400V UPS IS60KH Page Page Page 80kVA 400V UPS IS80KH Page Page Page 100kVA 400V UPS IS100KH Page Page Page Page Page Mounting the drip shield Options - IP32 Drip Shield 990-2440 AIS 5000 400V Installation Manual 55 Drip shield sizes IP32 for 10 30 kVA and 80 100 kVA UPS IP32 for Battery Enclosure IP32 for 40 60 kVA UPS 56 AIS 5000 400V Installation Manual 990-2440 Relay Board K012 K013 K014 K015 K016 ALARM POSITION K001 K002 K003 K004 K005 K006 **************** * Message: ********* Communication Cards Cards and slots Programming and Set-Up Display Display introduction Display functions Programming and Set-Up - Display 990-2440 AIS 5000 400V Installation Manual 61 Display messages Mains = Utility Programming the UPS User stack Parameter Comments Page Page Page Page Settings for redundant systems Page Setting stack Page Operation Modes Operation mode descriptions: Normal to Bypass Operation Bypass to Normal Operation Normal to Manual Bypass Operation Programming and Set-Up - Operation Modes Manual Bypass to Normal Operation (including start up procedure) The load is now supported by the UP S. Page *990-2440* APC Worldwide Customer Support 990-2440 09/2005