Manuals / American Power Conversion / Household Appliance / Air Conditioner

American Power Conversion Central Air Conditioning System manual Network Management Card

Models: Central Air Conditioning System

1 84

Download 84 pages 23.05 Kb

Page 53

Network Management Card

Network Management Card

Quick Configuration

The NetworkAIR IR In-row Precision Air Conditioner is shipped with a Network Management Card that provides for the management of the Air Conditioner over your network. You must set up the Network Management Card in order to control the NetworkAIR IR In-row Precision Air Conditioner through a web browser.

Disregard the procedures in this section if you have APC InfraStruXure Manager as part of your system. See the InfraStruXure Manager documentation for more information.

Overview

You must configure the following TCP/IP settings before the NetworkAIR IR In-row Air Conditioner can operate on a network:

•IP address of the Network Management Card

•Subnet mask

•Default gateway

If a default gateway is unavailable, use the IP address of a computer that is located on the same subnet as the Network Management Card and that is usually running. The Network Management Card uses the default gateway to test the network when

Note traffic is very light.

See “Watchdog Features” in the “Introduction” of the User’s Guide for more information about the watchdog role of the default gateway.

NetworkAIR IR Operation, Maintenance, and Troubleshooting

47

Image 53

American Power Conversion Central Air Conditioning System manual Network Management Card, Quick Configuration

Contents

In-row Operation, Maintenance, and TroubleshootingNetworkAIR IR Precision Air Conditioner Page Operation ContentsPage Network Management Card Warranty MaintenanceTroubleshooting Function OperationDisplay Interface Scrolling status screens Using the DisplayNavigating the interface Operation Using the DisplayMain menu screen The Module has two levels of password protection Stop the System Set Up System Configuration Up Down Horizontal System Delays Baud Rate. The bus speed for the RS-485bus Fluid-CoilType Options for Fluid-CooledModulesApplicable Settings Operation Options for Fluid-CooledModules Valve TypesActuator Types Coil Fluid Temp Activation Threshold and Deadband Set Up Contacts and Relays Map. Choose alarms or events to map to this relay Page Alarm detectors Set Up Module ConfigurationConfigure Module Set Up Module Control Reset humidifier Reset variable frequency driveSet up Humidifier Operation Set Up Module ControlReset compressors How the modes work Control the EnvironmentCool 61.8-90.0F16.5 to 32.2C Cool 0.5-10.0F 0.28 -5.6C PID controls room load 1.Select the PID loop to tune Humidification sensitivity Set Up Alarms Blower Blower Heater Humidifier Set Up Group Sys failure events Group settingsMode RangePage Set Up the Display To update the controller firmware 7.Restart the System Network config Set Up Network ConfigurationView Status Readings Manufacturer Name Model Number The name of the alarm Respond to Alarms Operation Respond to Alarms Clear active alarmsReset sys failure Action Required Alarm messages and suggested actionsDisplayed Alarm Message Action Required Displayed Alarm MessageAction Required Displayed Alarm MessageEnv Temperature Low Action Required Displayed Alarm MessageReset Humidifier Remote Sensor Added Displayed Alarm MessageAction Required Action Required Displayed Alarm MessageOperation Respond to Alarms Page Network Management Card Quick ConfigurationAPC Device IP Configuration Wizard TCP/IP configuration methodsBOOTP & DHCP configuration Network Management Card Quick ConfigurationSee “BOOTP” on this page or “DHCP” on page Configuration” in the User’s Guide 2. Use the configuration cable APC part 1.Choose Network from the Control Console menu 5.Press CTRL-C to exit to the Control Console menu Overview How to Access a Configured UnitWeb interface Telnet/SSHSNMP FTP/SCP How to Recover From a Lost Password How to Upgrade Firmware 5. Upgrade the AOS. For example Page Monthly Preventive Maintenance MaintenanceVerify that the condensate line is flowing freely Quarterly Preventive Maintenance Verify the following modes of operation Functional testsFull cooling Full reheat Humidification DehumidificationSemi-AnnualPreventive Maintenance Page Problem TroubleshootingPossible Cause Corrective ActionPossible Cause ProblemCorrective Action Airflow too highPossible Cause ProblemCorrective Action HumidifierPage Limited Product Warranty for APC Products WarrantyAssignment of warranties Limited Product Warranty for APC ProductsDrawings, descriptions ExclusionsPage Warranty Procedures Parts Warranty ProceduresPage Page 990-2260-001 APC Worldwide Customer Support990-2260-001 01/2005