Port Access Control | Asus GigaX instruction

GigaX Series L3 Managed Switch User Guide

•Multi-host: If enabled, ALL hosts connected to the selected port are allowed to use the port if ONE of the hosts passed the authentication. If disabled, only ONE host among other hosts passed the authentication is allowed to use the port.

•Authentication Control: If 'force_authorized' is selected, the selected port is forced authorized. Thus, traffic from all hosts is allowed to pass. Otherwise, if 'force_unauthorized' is selected, the selected port is blocked and no traffic can go through. If 'Auto' is selected, the behavior of the selected port is controlled by 802.1x protocol. All ports should be set to 'Auto' under normal conditions.

•Guest VLAN: Specify a guest VLAN to clients that are not

802.1x-capable.

Click to make the settings permanent. Click to refresh the settings to current value.

Figure 42. Port Access Control

71

Image 71

Asus GigaX manual Port Access Control

Contents

GigaX Series Copyright 2005 ASUSTeK Computer INC. All Rights Reserved Exxxx First Edition March Canadian Department of Communications Statement Federal Communications Commission Statement Asus Computer GmbH Germany and Austria ASUSTeK Computer INC. Asia-PacificAsus Computer International America Table of Contents Physical Interface Security 120 Overview of Hardware Connections List of Figures Using the nslookup utility 120 List of Tables Introduction L3 managed features MIB-II Typography SymbolsConventions used in this document Notations Getting to know the GigaX Package contents Front panel Front Panel Front panel labels and LEDs Rear Panel Technical specifications Quick start guide Part 1 Installing the hardwareInstalling the switch on a flat surface Mounting the switch on a rack Connect to the computers or a LAN Part 2 Setting up the switchAttach the power adapter Connect the console port Overview of Hardware Connections Setting up through the console port Part 3 Basic switch setting for management GigaX Series L3 Managed Switch User Guide Login and IP setup Screen Http//192.168.1.1 Setting up through the Web interface IP Setup Log into Web user interface Management with the Web Interface Home Functional layout Top Frame Expanded Menu List Commonly used buttons and icons Menu navigation tips Management System Pages IP Setup Reboot Administration Firmware Upgrade Firmware Upgrade Physical Interface Physical Interface Interfaces Route Interfaces Static Route Static Route 3 RIP RIP Bridge Spanning Tree/Rapid Spanning Tree Spanning Tree Link Aggregation GigaX Series L3 Managed Switch User Guide Link aggregation Mirroring Mirroring Igmp Snooping Static Multicast Igmp Snooping Traffic Control Traffic Control Dynamic Addresses Dynamic Address Static Addresses Static Address Tagged Vlan Tagged Vlan Default Port Vlan and CoS Default Port Vlan and CoS Dhcp Snooping CoS Queue Mapping Dhcp Snooping Community Table Snmp Host Table Host Table Vacm Group Trap Setting Vacm Group Vacm View Vacm View USM User USM User Filter Set Filters Filter Set Filter Rule in MAC mode Filter Attach Filter Attach Security Port Access Control Port Access Control Dial-In user Dial-In User Radius Radius Traffic Comparison Statistics Chart Historical Status Error Group Historical Status Save Configuration Save Configuration Console Interface CLI interface Power On Self Test Boot ROM Command Mode Boot ROM Command Mode Boot ROM commands Boot ROM Commands System Name Login and LogoutCLI Commands System Commands System Location System Contact IP Address Default GatewayPassword Protection is Enabled/Disabled New Password Verify Password Upload Physical Interface CommandsReboot Flow Control Enable/Disable Route Commands Delete Static Route CLI command l3 rip show Enable/Disable RIPRIP-enabled interfaces Add Static Route RIP-disabled interfaces Bridge Commands Show Trunk CLI command l2 trunk show trunk id Create Trunk Lacp System Priority Mirror Mode Enable/Disable Monitor Port port numberAdd/Remove Trunk Lacp Action Remove Multicast Group CLI command l2 mcast show Set Multicast GroupCLI command l2 mcast set Show Multicast Group Limit CLI command l2 igmp start/stop ReloadCLI command l2 rate limit limit rate Reload Aging Time CLI command l2 arl port port number Query by Vlan IDCLI command l2 arl vlan vlan id Query by MAC Address CLI command l2 arl mac mac address MAC Address Remove Vlan CLI command l2 vlan show vlan id NameShow Vlan Dhcp Snoop Dhcp Snooping RetrievePriority CoS Queue New community string new community string SnmpAdd/Remove Trusted Port Community Name Set Host IP Address Community CLI command snmp host setCommunity entry table index entry id to delete Trap Version v1/v2c Destination Community for Trap CLI command snmp trap addCLI command snmp trap set Entry id table index entry id to delete Retrieve Security Model 0/1/2/3any/v1/v2c/usm old security model new View Subtree oid view subtree View Mask view mask 100 Access entry entry id to delete RetrieveView Name View Type View Subtree View Mask View entry entry id to delete Retrieve View Type1/2included/excluded view typeView Subtree oid old view subtree new view subtree View Type1/2included/excluded old view type new view type 102 USM user entry entry id to delete Retrieve New Filters Commands 104 GigaX Series L3 Managed Switch User Guide 106 Rule ListAttach Security Commands Retransmission Time Max Reauthentication AttemptsAuthentication Control Quiet Period Dynamic Vlan dynamic Vlan User Name Password Confirm Password Dynamic Vlan 110 Reset SSH keyGenerate SSH key Show Generating Status 112 Structure of an IP address IP Addresses, Network Masks, and SubnetsIP Addresses 114 IP address structure Network classes 255.255.255.192 or 11111111 116 Subnet masks11111111 117 Ping TroubleshootingDiagnosing problems using IP utilities Ping Using the ping utility 120 NslookupNslookup Loosening the thumbscrew Replacing defective fans 122 Fan specifications Simple fixes Troubleshooting 124 Button in the Save Configuration 10BASE-T Glossary Ethernet 126 127 IP address 128 129 Ping 130 131 Tftp 132 133 134 Index GigaX Series L3 Managed Switch User Guide 136 GigaX Series L3 Managed Switch User Guide