136 | Asus GigaX instruction

recovering, 135

Physical Interface Commands, 95

Physical Interface page, 42 Ping, 128, 141

Port, 141

POST, 89

Power adapter, 23 Power On Self Test, 89 Protocol, 141

Quick Configuration console logging in, 25

Reboot page, 40

Remote, 141

RJ-45, 141

Routing, 142

RPS module, 23

Save Configuration page, 87 Set page, 74

SNMP, 142

SNMP Commands, 106

SNMP pages, 67

Spanning Tree Commands, 96 Spanning Tree page, 47 Static Address Commands, 102 Static Address page, 60 Static Multicast page, 56 Statistics Chart pages, 84 STP, 142

Subnet, 142

Subnet mask. See Network mask Subnet masks, 126

System Commands, 92 Tagged VLAN Commands, 103 Tagged VLAN page, 61 TCP/IP, 142

Telnet, 143

TFTP, 143

Traffic Comparison page, 84 Traffic Control Commands, 101 Traffic Control page, 58

Trap Setting Commands, 108

136

Image 136

Asus GigaX manual 136

Contents

GigaX Series Exxxx First Edition March Copyright 2005 ASUSTeK Computer INC. All Rights Reserved Federal Communications Commission Statement Canadian Department of Communications Statement Asus Computer International America ASUSTeK Computer INC. Asia-PacificAsus Computer GmbH Germany and Austria Table of Contents Physical Interface Security 120 List of Figures Overview of Hardware Connections Using the nslookup utility 120 List of Tables L3 managed features Introduction MIB-II Symbols Conventions used in this documentNotations Typography Package contents Getting to know the GigaX Front Panel Front panel Front panel labels and LEDs Technical specifications Rear Panel Part 1 Installing the hardware Installing the switch on a flat surfaceMounting the switch on a rack Quick start guide Part 2 Setting up the switch Attach the power adapterConnect the console port Connect to the computers or a LAN Overview of Hardware Connections Part 3 Basic switch setting for management Setting up through the console port GigaX Series L3 Managed Switch User Guide Login and IP setup Screen Setting up through the Web interface Http//192.168.1.1 IP Setup Management with the Web Interface Log into Web user interface Functional layout Home Top Frame Expanded Menu List Menu navigation tips Commonly used buttons and icons System Pages Management IP Setup Administration Reboot Firmware Upgrade Firmware Upgrade Physical Interface Physical Interface Route Interfaces Interfaces Static Route 3 RIP Static Route Bridge RIP Spanning Tree/Rapid Spanning Tree Link Aggregation Spanning Tree GigaX Series L3 Managed Switch User Guide Mirroring Link aggregation Mirroring Static Multicast Igmp Snooping Traffic Control Igmp Snooping Dynamic Addresses Traffic Control Dynamic Address Static Addresses Tagged Vlan Static Address Tagged Vlan Default Port Vlan and CoS Default Port Vlan and CoS CoS Queue Mapping Dhcp Snooping Dhcp Snooping Snmp Community Table Host Table Host Table Trap Setting Vacm Group Vacm View Vacm Group Vacm View USM User USM User Filters Filter Set Filter Set Filter Rule in MAC mode Filter Attach Filter Attach Port Access Control Security Port Access Control Dial-In User Dial-In user Radius Radius Statistics Chart Traffic Comparison Error Group Historical Status Historical Status Save Configuration Save Configuration Console Interface Power On Self Test CLI interface Boot ROM Command Mode Boot ROM Command Mode Boot ROM Commands Boot ROM commands Login and Logout CLI CommandsSystem Commands System Name System Contact System Location Default Gateway Password Protection is Enabled/DisabledNew Password Verify Password IP Address Physical Interface Commands RebootFlow Control Enable/Disable Upload Route Commands CLI command l3 rip show Enable/Disable RIP RIP-enabled interfacesAdd Static Route Delete Static Route Bridge Commands RIP-disabled interfaces CLI command l2 trunk show trunk id Create Trunk Show Trunk Mirror Mode Enable/Disable Monitor Port port number Add/Remove TrunkLacp Action Lacp System Priority CLI command l2 mcast show Set Multicast Group CLI command l2 mcast setShow Multicast Group Remove Multicast Group CLI command l2 rate limit limit rate Reload CLI command l2 igmp start/stop ReloadLimit CLI command l2 arl port port number Query by Vlan ID CLI command l2 arl vlan vlan id Query by MAC AddressCLI command l2 arl mac mac address MAC Address Aging Time CLI command l2 vlan show vlan id Name Show VlanDhcp Snoop Remove Vlan Priority CoS Queue RetrieveDhcp Snooping Snmp Add/Remove Trusted PortCommunity Name Set New community string new community string Community entry table index entry id to delete CLI command snmp host setHost IP Address Community CLI command snmp trap add CLI command snmp trap setEntry id table index entry id to delete Retrieve Trap Version v1/v2c Destination Community for Trap Security Model 0/1/2/3any/v1/v2c/usm old security model new View Name View Type View Subtree View Mask Access entry entry id to delete RetrieveView Subtree oid view subtree View Mask view mask 100 View Type1/2included/excluded view type View Subtree oid old view subtree new view subtreeView Type1/2included/excluded old view type new view type View entry entry id to delete Retrieve USM user entry entry id to delete Retrieve 102 Filters Commands New 104 GigaX Series L3 Managed Switch User Guide Attach Rule List106 Security Commands Max Reauthentication Attempts Authentication ControlQuiet Period Retransmission Time User Name Password Confirm Password Dynamic Vlan Dynamic Vlan dynamic Vlan Generate SSH key Reset SSH key110 Show Generating Status 112 IP Addresses IP Addresses, Network Masks, and SubnetsStructure of an IP address IP address structure 114 Network classes 11111111 Subnet masks255.255.255.192 or 11111111 116 117 Troubleshooting Diagnosing problems using IP utilitiesPing Ping Using the ping utility Nslookup Nslookup120 Replacing defective fans Loosening the thumbscrew Fan specifications 122 Troubleshooting Simple fixes Button in the Save Configuration 124 Glossary 10BASE-T 126 Ethernet 127 128 IP address 129 130 Ping 131 132 Tftp 133 Index 134 GigaX Series L3 Managed Switch User Guide 136 GigaX Series L3 Managed Switch User Guide