4in Phoenix RS32 / IR, Lan | Barco RCP-120 specs

Following are descriptions of each rear panel connector:

1)4in Phoenix – RS32 / IR

This connector can be used to connect a serial port from a computer to the panel for configuration via the boot menu. When referenced, “Serial Port 1” is defined as pins GND, RS232 RX and RS232 TX. By default, t he following conditions are set:

∙Baud Rate: 9600

∙Data Bits: 8

∙Parity: None

∙Stop Bits: 1

∙Flow Control: None

Note

The IRX pin is not supported on the RCP120.

2)LAN

One RJ45 connector is provided for 10/100BaseT Eth ernet communications. By default, the following conditions are set:

∙DHCP = OFF

∙Default IP address: 192.168.0.100

∙Default Netmask: 255.255.255.0

The user can use the default address, or set a different address.

3)2in Phoenix – DC Power Input

One DC Connector is provided for connecting the remote control panel to 12V DC power using the supplied universal AC to DC power supply.

Remote Control Panel User’s Guide ● Rev 00

13

Image 13

Barco RCP-120 manual 4in Phoenix RS32 / IR, Lan, 2in Phoenix DC Power Input

Contents

RCP120 Remote Control Panel User’s Guide Copyright Remote Control Panel User’s Guide Rev Trademarks Company Address Use the Proper Power Cord Power SourceDo Not Remove Covers or Panels Grounding the Product Terms In This Manual and Equipment Marking Description Approved By 09/11 586290 Initial Release Rev Date Table of Contents Universal Power Supply This page intentionally left blank Overview Introduction Application Questions Connectivity Diagram RCP120 Front Panel Remote Control Panel OrientationRCP120 Rear Panel 4in Phoenix RS32 / IR 2in Phoenix DC Power InputLAN Unpacking and Inspection InstallationWhat’s Included in the Box RCP120 Installation Soft Reboot / Web Interface Password Reset RCP120 ConfigurationConnecting to the RCP120 Web Interface Remote Control Panel User’s Guide Rev RCP120 Configuration Network Configuration RCP120 Configuration Web InterfaceStatus Master Controller IP Address Change Admin Password Serial Port 2 Configuration / Baud Rate Serial Port 1 Configuration / Baud RateSerial Port 1 Auto Transmit Update and Reboot / Reset Defaults Button SettingsSeconds Before Default Setting is 0 No Timeout. Used to Delay Between Default Setting is 30 0.3 Seconds. Used to Connecting to the Boot Menu RCP120 Boot MenuOverview RCP120 Boot Menu Interface Discard Changes and Reboot Restore Default SettingsSave Changes and Reboot Selections Not Supported Assign Remote Panels RCP120 FSN Menu Orientation Figure below illustrates the Remote Control Panel Table Remote Control Panel Table Assign Remote Panels Menu Functions Discover Remote Panels Assign Aux Unassign Info Duplicate IP Address Notification No Connection Behavior OperationsDisplay IP/MAC Address and Firmware Version Understanding Button Mapping AUX Output Control Button Color Table Understanding Button Color Working with the RCP120 Remote Control Panel User’s Guide Rev FSN System and Controller Setup Setting up the RCP120 to Control an Aux OutputRCP20 Setup Adding Additional RCP20 Devices Maintenance OperationsUnassign an Aux Output from an RCP20 Working with an Unconnected RCP20 Controlling a Standard Aux Output Controlling an Aux Output with the RCP120 Program Preview Controlling an Aux Output defined as a Mixer Updating Software Software Update OverviewHardware Requirements Via FTP Site Downloading SoftwareRCP20revision #.zip Via Web Site RCP20 Firmware Upload Updating RCP120 Software Remote Control Panel User’s Guide Rev Physical and Electrical Specifications Specifications Agency Specifications Communications SpecificationsPower Connector Connector Specifications Serial Port Figure below illustrates the 4pin Phoenix powe r connector Installing a Power Blade Adapter Universal Power Supply Remote Control Panel User’s Guide Rev Return Material Authorization RMA WarrantyContact Information Barco, Inc Contact InformationSales Contact Information Barco N.V