Buffalo Technology TSXE80TLR5, TS-RXL user manual 119, Dhcp, Network is required for use

Network

Network

	DHCP	If enabled, DHCP will configure your IP settings automatically. A DHCP server on the
		network is required for use.
IP Address Settings	Primary IP Address	If DHCP is disabled, you can enter an IP address manually.
	Subnet Mask	Set a subnet mask.
Click [Modify
Settings] to change	Default Gateway	Specify the IP address for a default gateway..
settings.	Address
* The LAN cable
	Primary DNS	Specify an IP address of the primary DNS server.
connected to LAN
	Server
Port 2 should be
	Secondary DNS	Specify an IP address of the secondary DNS server.
set for Ethernet 2.
	Server
	Wake on LAN	Select [Enable] or [Disable] for [Wake on LAN].
		* TS-XEL series TeraStations do not support Wake on LAN.
EthernetFrameSize	Ethernet Frame	You can improve transmission efficiency by changing the maximum size of data that
Click [Modify	Size	can be sent at a time.
Settings] to change		• [1518 bytes (Default)]:	It is set to 1518 bytes at default.
settings.		• [4102 bytes (Jumbo Frame)]: Transfer at 4102 bytes.
* The LAN cable		• [7422 bytes (Jumbo Frame)]: Transfer at 7422 bytes.
connected to LAN		• [9694 bytes (Jumbo Frame)]: Transfer at 9694 bytes.
Port 2 should be
set for Ethernet 2.
	Network Services	[HTTP]: It is set to [Enable] by default.
		* You cannot open the Web Admin interface from a network for which [Disable] is selected.
		[HTTPS]: It is set to [Enable] by default.
		* You cannot open the Web Admin interface through SSL from a network for which [Disable] is
		selected.
		[SMB]: It is set to [Enable] by default.
		* You cannot access the TeraStation via SMB from a network where [Disable] is selected.
		[AFP]: It is set to [Enable] by default.
		* You cannot connect TeraStation via AFP from a Mac even if you add [AFP] in the shared folder
		settings.
		[FTP]: It is set to [Disable] by default.
		* You cannot connect to the TeraStation via FTP from a Mac, even if you add [FTP] to the shared
		folder settings.To use FTP, change this setting to [Enable].
		[Backup/Replication]: It is set to [Enable] by default.
		* You cannot use the TeraStation as a backup destination from a network connected for which
		[Disable] is selected.
		[NasNavi Detection]: It is set to [Enable] by default.
Network Services		* If disabled, NAS Navigator2 will not be able to detect the TeraStation.
		* NAS Navigator2 detection should be enabled to update firmware, use auto power
		management, or use NS-SHIFT.
		[NFS]: It is set to [Enable] by default.
		* You cannot access the TeraStation from NFS clients if [Disable] is selected.
		[SFTP]: It is set to [Enable] by default.
		* You cannot access the TeraStation via SFTP if [Disable] is selected.
		[WebAccess]: It is set to [Enable] by default.
		* You cannot access the TeraStation via WebAccess feature if [Disable] is selected.
		[TeraSearch]: It is set to [Enable] by default.
		* You cannot use the TeraSearch if [Disable] is selected.
		[Power Interlock]: It is set to [Enable] by default.
		* You cannot use the auto power management if [Disable] is selected.
		* If Ethernet 1 and 2 are both disabled, and the Power Mode Switch is set to AUTO, the
		TeraStation will not turn on. Move the Power Mode Switch to MANUAL to allow the
		TeraStation to power on again.
	Add/Edit SSL Key	Set when updating SSL Server certification and the private key.

TeraStation User Manual 119