Com, Transceiver Requirements | Cabletron Systems SEHI-24, SEHI-22

INSTALLATION REQUIREMENTS/SPECIFICATIONS

2.4COM PORT REQUIREMENTS

The RJ45 COM port supports access to a Local Management Console. The Console port supports a Digital Equipment Corporation, VT 320™ terminal or PC emulation of the VT 320™ terminal. Figure 2-8 shows the pinouts for the RJ45 COM port.

1 2 3 4 5 6 7 8

COM

1. Transmit Data		5.	Signal Ground
2.	Data Set Ready	6.	Data Terminal Ready
3.	Not Used	7.	Not Used
4.	Not Used	8.	Not Used

Figure 2-8. COM Port Pinouts

2.5TRANSCEIVER REQUIREMENTS

When you connect an external network segment, via a transceiver, to the SEHI with an EPIM-A, the following requirements must be met:

•The transceiver or Ethernet Device to which the module will be connected must meet IEEE 802.3 standards, and/or Ethernet Version 1.0 or Version 2.0 standards.

•The Signal Quality Error (SQE) test function on the transceiver must be disabled if you connect it to a repeater or to an Ethernet Version 1.0 device. In addition, some Version 2.0 equipment does not support the SQE test. Devices that do not support SQE test interpret the SQE test pulse as a collision.

Page 2-16

Image 30

Cabletron Systems SEHI-24, SEHI-22, SEHI-32, SEHI-34 manual Com, Transceiver Requirements

Contents

10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper FCC Notice DOC Notice Cabletron SYSTEMS, INC Program License Agreement Cabletron Software Program License Exclusion of Warranty Disclaimer of Liability United States Government Restricted Rights Table of Contents Troubleshooting InstallationConnecting to the Network Local Management Contents Appendix B Twisted Pair Wiring Tables A-1 Using this Manual Chapter Introduction Introduction Getting Help Sehi Overview Polarity Detection and Correction Sehi FeaturesRepeater Functionality Flash EEPROMs Local Management Reset ButtonLanview LEDs Stackable Capabilities Introduction Optional Features Epim Daughter Board Upgrade Kit Rack Mount or Wall Mount HardwareRelated Manuals Cable Specifications HubSTACK Interconnect Cable Requirements Impedance LengthInsertion Loss Jitter Crosstalk DelayTemperature Noise Fiber Optic Budget and Propagation Delay Cable Type Attenuation Maximum Cable Length Installation REQUIREMENTS/SPECIFICATIONS Cable Type ConnectorsThin-Net Network Requirements for the EPIM-C Module Terminators Network Port Specifications AUI Cable Requirements for the EPIM-A and EPIM-X ModulesAUI Cable SEHI-22 and SEHI-24 Network Port Speciﬁcations SEHI-32 and SEHI-34 Network Port Speciﬁcations Pin Champ Connector Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications EPIM-T EPIM-F1 and EPIM-F2 Parameter Typical Worst Worst Case Typical Value Budget EPIM-F3 EPIM-F3 Parameter Typical Minimum Maximum Connector Type EPIM-C EPIM-A and EPIM-X AUI Port EPIM-A and EPIM-X COM Transceiver Requirements General Delay Times Start of PacketsDelay Times JAM Preamble Output Min. Load Max. Load Max Power Fault ProtectionPower Supply Requirements JAM Output Safety Physical Installing the Sehi Unpacking the Sehi Stacking the Sehi Stacking the Sehi Attaching the Strain Relief Bracket Disconnect SEH and Sehi Interconnect Cables At the OUT Port Installing the Sehi in the Rack Rack Mounting the Sehi Wall Mounting the Sehi Free-Standing Installation Shelf or Table-top Installation Installation Connecting the Sehi to the Power Source Connecting the Sehi to the Network Connecting to Network Ports, SEHI-22 and SEHI-24 EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 Connecting a UTP Segment to an EPIM-T EPIM-T Cross-over Switch Connecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C Connecting an AUI Cable to an EPIM-A EPIM-A Connecting an AUI Cable to an EPIM-X Finishing the Installation On Position Toward Back Epim OFF Position Toward Front Chapter Troubleshooting Installation CHECK-OUT Using Lanview PWR CPU RCV Troubleshooting CLNUsing the Reset Button LNK Chapter Local Management Local Management Management Terminal Requirements Console Cable Conﬁguration Management Terminal Connection General Setup Management Terminal Setup ParametersMenu Function Selection Display Setup Setup Local Management Accessing Local Management Sehi Local Management Feature Selection Screen Local Management Using the Local Management Screens Community Name Table Screen Access Community Name Editing the Community Name Field Conﬁguration Screen IP Address Setting the IP Address Default GatewayPort Enable Override SubNet Mask Setting the Subnet Mask Setting the Default Gateway Using the Port Enable Override Exiting the Configuration Screen Trap Table Screen Traps Configuring the Trap TableSnmp Community Name Trap IP Address Exiting the Trap Table Screen Snmp Tools Screen Set OID PrependGet Get Next Step WalkRecall-OID Cycles Getting Individual OIDs Getting the Next OID Setting an OID Viewing Multiple OIDs Walking Through OIDs Stepping Through OIDsCycling Through OIDs Exiting the Snmp Tools Screen Device Statistics Screen Alignment Errors Errors ReceivedCRC Errors Port Admin. Status Update-Freq Enable PortDisable Port Port Seg. Status Using the Enable Port Command Selecting the Appropriate Module/Port Using the Disable Port Command Exiting the Device Statistics Screen Appendix a Twisted Pair Wiring Tables Twisted Pair Wiring Tables A-2 A-3 A-4 From Punch Down To RJ-45 Into Block Wallplate Ofﬁce 10BASE-TDrop Device A-6 A-7 SEHI-32/34 Punch Wall Plate Champ Down Block If Required Ethernet Device Figure A-1. Punch Down Block A-9 Spanish Power Supply CordGerman French