OID Prepend, Set, Get Next | Cabletron Systems SEHI-24, SEHI-22

LOCAL MANAGEMENT

SEHI LOCAL MANAGEMENT

Cabletron SEHI Revision X.XX.XX

SNMP TOOLS

SNMP COMMUNITY NAME: public

OID PREPEND: 1.3.6.1

GET	SET	GETNEXT WALK	RECALL-OID STEP CYCLES REPEAT
F6	F7	F8	F9

RETURN

F10

Figure 6-7. SNMP Tools Screen

The following sections describe SNMP Tools screen ﬁelds and instructions on how to change them.

Community Name

Identiﬁes the community name used as a password to determine access level to the MIB component.

OID Prepend

Speciﬁes the number preﬁx common to all Object Identiﬁers (OIDs) found in the MIBs - 1.3.6.1 is the default preﬁx OID. This is a modiﬁable ﬁeld.

Get

Lets you retrieve MIB objects using SNMP protocol.

Set

Lets users with Read-Write and Super-User access change modiﬁable MIB objects, using SNMP protocol.

Get Next

Displays the OID following the current OID.

Page 6-17

Image 74

Cabletron Systems SEHI-24, SEHI-22, SEHI-32, SEHI-34 manual OID Prepend, Set, Get Next

Contents

10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper FCC Notice DOC Notice Cabletron SYSTEMS, INC Program License Agreement Cabletron Software Program License Exclusion of Warranty Disclaimer of Liability United States Government Restricted Rights Table of Contents Troubleshooting InstallationConnecting to the Network Local Management Contents Appendix B Twisted Pair Wiring Tables A-1 Using this Manual Chapter Introduction Introduction Getting Help Sehi Overview Polarity Detection and Correction Sehi FeaturesRepeater Functionality Flash EEPROMs Local Management Reset ButtonLanview LEDs Stackable Capabilities Introduction Optional Features Epim Related Manuals Daughter Board Upgrade KitRack Mount or Wall Mount Hardware Cable Specifications HubSTACK Interconnect Cable Requirements Impedance LengthInsertion Loss Jitter Crosstalk DelayTemperature Noise Fiber Optic Budget and Propagation Delay Cable Type Attenuation Maximum Cable Length Installation REQUIREMENTS/SPECIFICATIONS Cable Type ConnectorsThin-Net Network Requirements for the EPIM-C Module Terminators AUI Cable Network Port SpecificationsAUI Cable Requirements for the EPIM-A and EPIM-X Modules SEHI-22 and SEHI-24 Network Port Speciﬁcations SEHI-32 and SEHI-34 Network Port Speciﬁcations Pin Champ Connector Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications EPIM-T EPIM-F1 and EPIM-F2 Parameter Typical Worst Worst Case Typical Value Budget EPIM-F3 EPIM-F3 Parameter Typical Minimum Maximum Connector Type EPIM-C EPIM-A and EPIM-X AUI Port EPIM-A and EPIM-X COM Transceiver Requirements General Delay Times Start of PacketsDelay Times JAM Preamble Output Min. Load Max. Load Max Power Fault ProtectionPower Supply Requirements JAM Output Safety Physical Installing the Sehi Unpacking the Sehi Stacking the Sehi Stacking the Sehi Attaching the Strain Relief Bracket Disconnect SEH and Sehi Interconnect Cables At the OUT Port Installing the Sehi in the Rack Rack Mounting the Sehi Wall Mounting the Sehi Free-Standing Installation Shelf or Table-top Installation Installation Connecting the Sehi to the Power Source Connecting the Sehi to the Network Connecting to Network Ports, SEHI-22 and SEHI-24 EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 Connecting a UTP Segment to an EPIM-T EPIM-T Cross-over Switch Connecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C Connecting an AUI Cable to an EPIM-A EPIM-A Connecting an AUI Cable to an EPIM-X Finishing the Installation On Position Toward Back Epim OFF Position Toward Front Chapter Troubleshooting Installation CHECK-OUT Using Lanview PWR CPU RCV Troubleshooting CLNUsing the Reset Button LNK Chapter Local Management Local Management Management Terminal Requirements Console Cable Conﬁguration Management Terminal Connection General Setup Management Terminal Setup ParametersMenu Function Selection Display Setup Setup Local Management Accessing Local Management Sehi Local Management Feature Selection Screen Local Management Using the Local Management Screens Community Name Table Screen Access Community Name Editing the Community Name Field Conﬁguration Screen IP Address Setting the IP Address Default GatewayPort Enable Override SubNet Mask Setting the Subnet Mask Setting the Default Gateway Using the Port Enable Override Exiting the Configuration Screen Trap Table Screen Traps Configuring the Trap TableSnmp Community Name Trap IP Address Exiting the Trap Table Screen Snmp Tools Screen Set OID PrependGet Get Next Step WalkRecall-OID Cycles Getting Individual OIDs Getting the Next OID Setting an OID Viewing Multiple OIDs Cycling Through OIDs Walking Through OIDsStepping Through OIDs Exiting the Snmp Tools Screen Device Statistics Screen Alignment Errors Errors ReceivedCRC Errors Port Admin. Status Update-Freq Enable PortDisable Port Port Seg. Status Using the Enable Port Command Selecting the Appropriate Module/Port Using the Disable Port Command Exiting the Device Statistics Screen Appendix a Twisted Pair Wiring Tables Twisted Pair Wiring Tables A-2 A-3 A-4 Drop Device From Punch Down To RJ-45 Into Block Wallplate Ofﬁce10BASE-T A-6 A-7 SEHI-32/34 Punch Wall Plate Champ Down Block If Required Ethernet Device Figure A-1. Punch Down Block A-9 Spanish Power Supply CordGerman French