EPIM-F1 and EPIM-F2 | Cabletron Systems SEHI-32, SEHI-22, SEHI-24

INSTALLATION REQUIREMENTS/SPECIFICATIONS

2.3.2EPIM-F1 and EPIM-F2

The EPIM-F1 and EPIM-F2 shown in Figure 2-4 support Multimode Fiber Optic cabling. Each EPIM has an internal Cabletron Systems FOT-F™ Fiber Optic Transceiver. The EPIM-F1 is equipped with SMA Connectors and the EPIM-F2 is equipped with ST Connectors. Speciﬁcations for the EPIMs are listed below.

	Figure 2-4. EPIM-F1 and EPIM-F2
Parameter	Typical	Worst	Worst Case Typical
	Value	Case	Budget	Budget
Receive
Sensitivity:	-30.5 dBm	-28.0 dBm	—	—
Peak Input
Power:	-7.6 dBm	-8.2 dBm	—	—
Transmitter Power
50/125 ∝m
fiber:	-13.0 dBm	-15.0 dBm	13.0 dB	17.5 dB
62.5/125 ∝m
fiber:	-10.0 dBm	-12.0 dBm	16.0 dB	20.5 dB
100/140 ∝m
fiber:	-7.0 dBm	-9.0 dBm	19.0 dB	23.5 dB
Error Rate:	Better than 10-10

Note: The transmitter power levels and receive sensitivity levels listed are Peak Power Levels after optical overshoot. A Peak Power Meter must be used to correctly compare the values given above to those measured on any particular port. If Power Levels are being measured with an Average Power Meter, then 3 dBm must be added to the measurement to correctly compare those measured values to the values listed (i.e. -30.5 dBm peak=-33.5 dBm average).

Page 2-11

Image 25

Cabletron Systems SEHI-32, SEHI-22, SEHI-24 EPIM-F1 and EPIM-F2, Parameter Typical Worst Worst Case Typical Value Budget

Contents

10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper DOC Notice FCC Notice Cabletron Software Program License Cabletron SYSTEMS, INC Program License Agreement United States Government Restricted Rights Exclusion of Warranty Disclaimer of Liability Table of Contents Connecting to the Network InstallationTroubleshooting Local Management Contents Appendix B Twisted Pair Wiring Tables A-1 Chapter Introduction Using this Manual Sehi Overview Introduction Getting Help Repeater Functionality Sehi FeaturesPolarity Detection and Correction Flash EEPROMs Lanview LEDs Reset ButtonLocal Management Stackable Capabilities Epim Introduction Optional Features Rack Mount or Wall Mount Hardware Daughter Board Upgrade KitRelated Manuals HubSTACK Interconnect Cable Requirements Cable Specifications Insertion Loss LengthImpedance Jitter Temperature DelayCrosstalk Noise Cable Type Attenuation Maximum Cable Length Fiber Optic Budget and Propagation Delay Installation REQUIREMENTS/SPECIFICATIONS Thin-Net Network Requirements for the EPIM-C Module ConnectorsCable Type Terminators AUI Cable Requirements for the EPIM-A and EPIM-X Modules Network Port SpecificationsAUI Cable SEHI-32 and SEHI-34 Network Port Speciﬁcations SEHI-22 and SEHI-24 Network Port Speciﬁcations Pin Champ Connector EPIM-T Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications Parameter Typical Worst Worst Case Typical Value Budget EPIM-F1 and EPIM-F2 EPIM-F3 EPIM-F3 Parameter Typical Minimum Maximum EPIM-C Connector Type EPIM-A and EPIM-X EPIM-A and EPIM-X AUI Port Transceiver Requirements COM Delay Times JAM Delay Times Start of PacketsGeneral Preamble Power Supply Requirements Fault ProtectionOutput Min. Load Max. Load Max Power JAM Output Physical Safety Unpacking the Sehi Installing the Sehi Stacking the Sehi Stacking the Sehi Disconnect SEH and Sehi Interconnect Cables At the OUT Port Attaching the Strain Relief Bracket Rack Mounting the Sehi Installing the Sehi in the Rack Wall Mounting the Sehi Shelf or Table-top Installation Free-Standing Installation Installation Connecting the Sehi to the Power Source Connecting to Network Ports, SEHI-22 and SEHI-24 Connecting the Sehi to the Network EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 EPIM-T Cross-over Switch Connecting a UTP Segment to an EPIM-T Connecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C EPIM-A Connecting an AUI Cable to an EPIM-A Connecting an AUI Cable to an EPIM-X On Position Toward Back Epim OFF Position Toward Front Finishing the Installation Installation CHECK-OUT Chapter Troubleshooting Using Lanview CPU PWR Using the Reset Button Troubleshooting CLNRCV LNK Chapter Local Management Local Management Management Terminal Requirements Management Terminal Connection Console Cable Conﬁguration Menu Function Selection Display Setup Management Terminal Setup ParametersGeneral Setup Setup Sehi Local Management Local Management Accessing Local Management Feature Selection Screen Community Name Table Screen Local Management Using the Local Management Screens Community Name Access Editing the Community Name Field IP Address Conﬁguration Screen Port Enable Override Default GatewaySetting the IP Address SubNet Mask Setting the Subnet Mask Using the Port Enable Override Setting the Default Gateway Trap Table Screen Exiting the Configuration Screen Snmp Community Name Configuring the Trap TableTraps Trap IP Address Snmp Tools Screen Exiting the Trap Table Screen Get OID PrependSet Get Next Recall-OID WalkStep Cycles Getting the Next OID Getting Individual OIDs Viewing Multiple OIDs Setting an OID Stepping Through OIDs Walking Through OIDsCycling Through OIDs Device Statistics Screen Exiting the Snmp Tools Screen CRC Errors Errors ReceivedAlignment Errors Port Admin. Status Disable Port Enable PortUpdate-Freq Port Seg. Status Selecting the Appropriate Module/Port Using the Enable Port Command Exiting the Device Statistics Screen Using the Disable Port Command Twisted Pair Wiring Tables Appendix a Twisted Pair Wiring Tables A-2 A-3 A-4 10BASE-T From Punch Down To RJ-45 Into Block Wallplate OfﬁceDrop Device A-6 A-7 Champ Down Block If Required Ethernet Device SEHI-32/34 Punch Wall Plate Figure A-1. Punch Down Block A-9 German Power Supply CordSpanish French