Cabletron Systems SEHI-32, SEHI-22, SEHI-24, SEHI-34 instruction

INSTALLATION

3.3CONNECTING THE SEHI TO THE POWER SOURCE

Note: The SEHI has a universal power supply. This allows you to connect the SEHI to power sources from 90 Vac to 264 Vac, 47-63 Hz.

To connect the SEHI to the power source:

1.Plug the power cord into the back panel of the SEHI.

2.Plug the other end of the power cord into a grounded wall outlet.

3.Verify that the PWR LED is on, this indicates that the SEHI is receiving power. After the SEHI runs a self test, the CPU LED blinks green indicating normal operation. If the LED remains red, the processor is faulty.

Page 3-8

Image 41

Cabletron Systems SEHI-32, SEHI-22, SEHI-24, SEHI-34 manual Installation Connecting the Sehi to the Power Source

Contents

10BASE-T Intelligent Stackable HUB USER’S Guide Printed On Recycled Paper DOC Notice FCC Notice Cabletron Software Program License Cabletron SYSTEMS, INC Program License Agreement United States Government Restricted Rights Exclusion of Warranty Disclaimer of Liability Table of Contents Connecting to the Network InstallationTroubleshooting Local Management Contents Appendix B Twisted Pair Wiring Tables A-1 Chapter Introduction Using this Manual Sehi Overview Introduction Getting Help Repeater Functionality Sehi FeaturesPolarity Detection and Correction Flash EEPROMs Lanview LEDs Reset ButtonLocal Management Stackable Capabilities Epim Introduction Optional Features Related Manuals Daughter Board Upgrade KitRack Mount or Wall Mount Hardware HubSTACK Interconnect Cable Requirements Cable Specifications Insertion Loss LengthImpedance Jitter Temperature DelayCrosstalk Noise Cable Type Attenuation Maximum Cable Length Fiber Optic Budget and Propagation Delay Installation REQUIREMENTS/SPECIFICATIONS Thin-Net Network Requirements for the EPIM-C Module ConnectorsCable Type Terminators AUI Cable Network Port SpecificationsAUI Cable Requirements for the EPIM-A and EPIM-X Modules SEHI-32 and SEHI-34 Network Port Speciﬁcations SEHI-22 and SEHI-24 Network Port Speciﬁcations Pin Champ Connector EPIM-T Installation REQUIREMENTS/SPECIFICATIONS Epim Specifications Parameter Typical Worst Worst Case Typical Value Budget EPIM-F1 and EPIM-F2 EPIM-F3 EPIM-F3 Parameter Typical Minimum Maximum EPIM-C Connector Type EPIM-A and EPIM-X EPIM-A and EPIM-X AUI Port Transceiver Requirements COM Delay Times JAM Delay Times Start of PacketsGeneral Preamble Power Supply Requirements Fault ProtectionOutput Min. Load Max. Load Max Power JAM Output Physical Safety Unpacking the Sehi Installing the Sehi Stacking the Sehi Stacking the Sehi Disconnect SEH and Sehi Interconnect Cables At the OUT Port Attaching the Strain Relief Bracket Rack Mounting the Sehi Installing the Sehi in the Rack Wall Mounting the Sehi Shelf or Table-top Installation Free-Standing Installation Installation Connecting the Sehi to the Power Source Connecting to Network Ports, SEHI-22 and SEHI-24 Connecting the Sehi to the Network EPIM-2 Connecting to Network Ports, SEHI-32 and SEHI-34 EPIM-T Cross-over Switch Connecting a UTP Segment to an EPIM-T Connecting to the Network Connecting to the Network Connecting to the Network Connecting a Thin-Net Segment to an EPIM-C EPIM-C EPIM-A Connecting an AUI Cable to an EPIM-A Connecting an AUI Cable to an EPIM-X On Position Toward Back Epim OFF Position Toward Front Finishing the Installation Installation CHECK-OUT Chapter Troubleshooting Using Lanview CPU PWR Using the Reset Button Troubleshooting CLNRCV LNK Chapter Local Management Local Management Management Terminal Requirements Management Terminal Connection Console Cable Conﬁguration Menu Function Selection Display Setup Management Terminal Setup ParametersGeneral Setup Setup Sehi Local Management Local Management Accessing Local Management Feature Selection Screen Community Name Table Screen Local Management Using the Local Management Screens Community Name Access Editing the Community Name Field IP Address Conﬁguration Screen Port Enable Override Default GatewaySetting the IP Address SubNet Mask Setting the Subnet Mask Using the Port Enable Override Setting the Default Gateway Trap Table Screen Exiting the Configuration Screen Snmp Community Name Configuring the Trap TableTraps Trap IP Address Snmp Tools Screen Exiting the Trap Table Screen Get OID PrependSet Get Next Recall-OID WalkStep Cycles Getting the Next OID Getting Individual OIDs Viewing Multiple OIDs Setting an OID Cycling Through OIDs Walking Through OIDsStepping Through OIDs Device Statistics Screen Exiting the Snmp Tools Screen CRC Errors Errors ReceivedAlignment Errors Port Admin. Status Disable Port Enable PortUpdate-Freq Port Seg. Status Selecting the Appropriate Module/Port Using the Enable Port Command Exiting the Device Statistics Screen Using the Disable Port Command Twisted Pair Wiring Tables Appendix a Twisted Pair Wiring Tables A-2 A-3 A-4 Drop Device From Punch Down To RJ-45 Into Block Wallplate Ofﬁce10BASE-T A-6 A-7 Champ Down Block If Required Ethernet Device SEHI-32/34 Punch Wall Plate Figure A-1. Punch Down Block A-9 German Power Supply CordSpanish French