Using the Song Sequencer

6. Use the R-17 (u, i) buttons to move the

 

 

 

 

 

 

Using Panel Record to Rewrite

 

cursor, use the dial or the R-14 (–, +) buttons to

 

 

 

 

 

Song Header Settings

 

change the value at the cursor position, and

 

 

 

then press the R-16 (ENTER) button.

 

The header of each song contains “header settings”, which

 

If you have already specified a range using the locator

 

are settings that were in effect on the Digital Keyboard when

 

 

screen (page E-80), you can copy that range to this

 

recording was performed. You can use a “panel record”

 

 

screen by holding down the L-12 (REPEAT) button.

 

operation to rewrite a song’s header settings with the Digital

 

 

 

 

 

 

 

 

 

Keyboard’s current setup.

 

 

 

 

 

 

 

 

 

The following items are header settings that can be rewritten

 

 

 

 

 

 

 

 

 

using the panel record operation.

 

 

 

 

 

 

 

 

 

Rhythm selection

 

 

 

 

 

 

 

 

 

• Tempo setting

 

 

 

 

 

 

 

 

 

Scale setting

 

 

 

 

 

 

 

 

 

The mixer settings below

 

 

 

 

 

 

 

 

 

 

– All part parameters from A04 through A07 and B01

 

 

 

 

 

 

 

 

 

 

through B16 (Excluding part on/off)

 

 

 

 

 

 

 

 

 

 

– Part parameters from A09 through A16: part on/off,

 

 

 

 

 

 

 

 

 

 

coarse tune, fine tune, scale enable, DSP line

 

 

Recording start point

 

Recording end point

 

 

 

 

 

 

 

– DSP parameters: volume, pan, reverb send

 

 

 

 

 

 

 

 

 

 

7. After specifying the recording start point and

 

Effect settings

 

• Accomp volume

 

end point, press the L-16 (START/STOP) button.

 

• UPPER 1 part tone, UPPER 2 part tone, and LOWER part

 

This starts punch-in playback. You can perform fast

 

 

tone selections

 

 

 

 

 

 

 

forward and fast backward operations during punch-in

 

To perform a panel record operation

 

 

playback using the operations described in step 6

 

 

 

under “To start re-recording from a particular location

 

1. Press the C-4 (SONG SEQUENCER) button to

 

 

during playback (Manual Punch-in)” (page E-76).

 

 

• You can start punch-in playback from one measure

 

 

enter the song sequencer mode.

 

 

prior to the current recording start point by pressing the

 

 

 

 

 

 

L-12 (REPEAT) button which causes the ?

 

 

 

 

 

 

indicator to appear on the display.

 

 

 

 

8. When playback reaches the re-record point you

 

 

 

 

 

 

 

 

 

 

 

 

 

specified, start playing something on the

 

 

 

 

 

keyboard.

 

 

 

 

 

2. Use the dial or R-14 (–, +) buttons to select a

 

Punch-in recording will start automatically when

 

 

 

playback reaches the record start point you specified.

 

 

song area number.

 

 

The C-3 (RECORD) button will light when recording

 

3. Configure panel settings so they reflect the

 

 

starts.

 

 

 

 

 

 

Recording stops and punch-in recording is exited

 

 

settings you want to write as the header

 

 

automatically when the record end point you specified

 

 

 

 

 

 

settings.

 

 

is reached. At this time the C-3 (RECORD) button will

 

 

 

 

 

 

• You can configure the following settings: mixer settings,

 

 

become unlit.

 

 

 

 

 

 

 

If you want to stop recording before the record end

 

 

tempo, system track rhythm, track tone selection, etc.

 

 

point you specified is reached, press the L-16 (START/

 

 

• To change the system track UPPER 1, UPPER 2, and

 

 

STOP) button. Any previously recorded data in the

 

 

LOWER part tones or mixer settings, use the mixer to

 

 

track that comes after the point you stopped punch-in

 

 

change the settings of parts A05 (UPPER 1), A06

 

 

recording will remain in the track.

 

 

(UPPER 2), and A07 (LOWER).

 

When “EOT” (End of Track) is selected for the

 

4. After all of the panels settings are the way you

 

 

recording start point, the start point for punch-in

 

 

 

 

 

want, hold the R-13 (FUNCTION) button as you

 

 

recording is the end of the track.

 

 

 

When “OFF” is selected for the recording end point,

 

 

press the C-17 (MENU) button.

 

 

punch-in recording will not stop automatically because

 

 

• This displays the song sequencer menu.

 

 

no end point is specified. To stop punch-in recording in

 

 

 

 

 

 

this case, press the L-16 (START/STOP) button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E-78