6.Insert the two ISOFIX connectors into the corresponding ISOFIX locking devices, lo- cated on the car seat, between the backrest and the seat (diag. 13). WARNING! Ensure that the two ISOFIX connectors are locked correctly into position, checking that the two (Z) signs are green.
7.Push the child car seat firmly against the backrest of the car seat (diag. 14) to ensure maximum adherence.
HOW TO FIT THE TOP TETHER
The installation of the child car seat is com- plete only by fitting the Top Tether. WARNING! Pease refer to the instructions booklet of the vehicle to identify the locking point of the Top Tether of the child car seat. This locking point is marked by a specific label (diag. 15), and it may be located in the po- sitions indicated in the diagrams 16a – 16b
– 16c – 16d – 16e.
WARNING! Check that the Top Tether is locked with the correct locking device. Do not mistake the locking device of the Top Tether with the ring provided for securing the luggage (diag. 17).
WARNING! Insert the Top Tether between the top part of the backrest of the car seat and the headrest. Never insert the Top Tether above the headrest (diag. 18).
8.After identifying the locking point, connect the hook (DD) of the Top Tether (diag. 19).
9.Adjust the length of the Top Tether belt, pulling the strap firmly to tension it cor- rectly (diag. 20). The belt is tensioned cor- rectly when the indicator located on the strap is green (diag. 21).
10.Roll up the excess strap and fix it with the specific Velcro strap provided (diag. 22).
HOW TO REMOVE THE ISOFIX SYSTEM WARNING! Remove the child from the child car seat before proceeding to the removal of the ISOFIX system.
1.Loosen the Top Tether by pressing the ap- propriate button BB (diag. 23), then release the hook.
2.Roll up the Top Tether strap and fix it with the appropriate Velcro strap (diag. 22).
3.Pull the unlocking handle of the ISOFIX system externally (L) and, while keeping it pulled, detach the child car seat from the backrest of the car seat, until the ISOFIX system is removed completely (diagrams
4.Push the two red buttons inside and relea-
se the connectors from the corresponding ISOFIX locking devices, located on the car seat (diag. 25).
5.Remove from the base of the child car seat the two caps stored in advance, and rein- sert them in the related ISOFIX connectors, paying attention that the two ends are fa- cing inside (diagrams
6.Push the ISOFIX system inside the base of the child car seat, inserting it completely into the base (diag. 27).
FITTING THE CHILD SEAT INTO THE CAR WITH A
1.Place the child car seat on the desired car seat. WARNING! Ensure there are no objects placed between the child car seat and the car seat, or the child car seat and car door.
2.Recline the backrest of the child car seat fully, pulling the lever located under the seat in your direction (Q) (Diag. 28).
3.Pull the car safety belt, sliding it in the spa- ce between the backrest and the base of the child car seat (Diag. 29).
4.Insert the lap section of the
5.Pull out the safety belt from the other side of the child car seat, and fasten it to the seat buckle (Diag. 31).
6.Open the safety belt locking clamp (T), lo- cated on the same side of the seat buckle, by pressing the lever (diag. 32).
7.Insert the diagonal section of the car safety belt into the clamp, and place the diagonal section as shown in diag. 33. When relea- sed, the clamp lever will automatically re- turn to the locked position.
8.Pull the diagonal section of the car safety belt firmly, ensuring that the child car seat adheres correctly to the car seat (diag. 34). If necessary, carry out this operation exer- cising some pressure on the child car seat with your knee.
37
