Cisco Systems 12006, 12406 manual

Chapter 3 Installing the Router

Supplemental Bonding and Grounding Connections

Figure 3-4 Supplemental Bonding and Grounding Port for NEBS

Compliance

GIGABIT ROUTE PROCESSOR

CISCO 12000

GIGABIT SWITCH ROUTER

57744

Use a dual-hole lug to connect to the chassis with two 6.3-mm (M6) screws on the 0.63-inch (16-mm) centers as shown in Figure 3-4and Figure 3-5. The lug can be ordered from Cisco (Part Number 32-0607-01).

Figure 3-5

Cable Lug

2.24

End View

					Ø 0.267

0.48
0.48					2 holes
					2 holes

0.25 0.63 0.37 0.08

All measurements in inches

Crimp area

25527

The dual-hole lug is crimped onto a grounding wire of a wire size and length determined by your router location and facility environment. The crimping tool shown in Figure 3-6is a standard crimping tool obtainable from many sources.

	Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
3-10	OL-11497-03

Image 10

Cisco Systems 12006, 12406 manual Supplemental Bonding and Grounding Port for Nebs Compliance

Contents

Installing the Router Installing a Router Installing the Optional Rack-Mount Brackets Installing the Rack-Mount Brackets OptionalTools and Equipment Required Installing the Optional Rack-Mount Brackets Installing Center-Mount Brackets Optional Lower and Upper Center-Mount Brackets Installing the Optional Center-Mount Brackets Repeat through for both upper center-mount brackets Installing the Chassis in a Rack Power supply OL-11497-03 Installing the Chassis on a Tabletop or Flat Surface Supplemental Bonding and Grounding Connections Supplemental Bonding and Grounding Port for Nebs Compliance Connecting RP and Line Card Cables Crimping the Lug Chassis Cable-Management Bracket Connecting Alarm Card Cables Connecting to the Console and Auxiliary Ports GRP Console and Auxiliary Ports GRP Console DCE and Auxiliary DTE Port Connections GRP Auxiliary Port Signals GRP Console Port SignalsPin Signal Input/Output Description RTS PRP Console and Auxiliary Ports PRP Console and Auxiliary Port Connections PRP Console Port Signals Console Port Pin Signal Input/Output Description PRP Auxiliary Port Signals Installing a Flash Memory CardAuxiliary Port Pin Signal 10 Flash Memory Card Slot Opening Connecting the GRP to an Ethernet Network 11 RJ-45 and MII Ethernet Connections Pin1 Out Input/Output Description Code MDC Pin Out Input/Output Description Code Pin Connecting the PRP to an Ethernet Network Pin Signal 14 Using the Ethernet Port on the PRP Ethernet Port Pin Signal Description PRP Ethernet Connections Crossover Cable Pinout for Connecting Two PRPs Parameter RJ-45 Connecting to an AC Power SourceParameter Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm IOS Software Configuration for the Router Cisco IOS Software Images Conditions to Check Before System Startup Overview of the Boot Process Starting the Router and Observing Initial Conditions OL-11497-03 RP Alphanumeric LED Display Meaning Source RP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH System Configuration Dialogue External Network Interface Locating a Valid Cisco IOS Software Image Manually Booting the SystemDir bootflash Dir slot0 Booting from the Cisco IOS Software Image Command Description Setup Command Router ConfigurationBefore You Begin Global Configuration Mode User Interface Command ModesCisco IOS User Interface User Exec Mode Privileged Exec Mode Subinterface Configuration Mode Interface Configuration ModeROM Monitor Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Passwords Configuring Global ParametersHost Name Configuring Network Interfaces Protocols GRP Ethernet Interfaces PRP Ethernet Interfaces Line Card Interfaces Checking the Software Version Show version CommandRouter# show version Show running Config Command Example Verifying the Running Configuration SettingsRouter# show running-config No service tcp-small-servers Hostname Router Show startup-config Command Saving the Running Configuration Settings to NvramReviewing the Running Configuration Settings Router# copy running-config startup-config No logging trap Using Flash Memory Cards in the RP Installing the Flash Memory Card in a RP Removing the Flash Memory Card from an RP Formatting a Flash Memory Card Router# configure terminal Specify a Boot ImageRouter# format slot0 Flash Memory Console Commands Router# cd slot1 Router# cd bootflash Router# delete slot0info Router# squeeze slot0 Routerconfig# config-reg Ctrl-Z Booting from Flash MemoryRouterconfig# boot system flash devicefilename Copying Files Router# copy tftpfilename bootflashslot0slot1 filename Router# copy tftpmyfile1 slot0myfile1 Copying a Cisco IOS Software Image Router# copy tftpnew.image slot0new.image Copying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Router# show bootvar Copy startup-config slot0 slot1filename Router# copy startup-config slot0myfile2 Router# dir slot0 Copy running-config slot0slot1filename Router# copy running-config slot0myfile2 Router# copy slot0myfile startup-config Copy slot0slot1filename startup-configRouter# copy startup-config running-config If You Need More Information Locked Blocks in Flash Memory Cards Installing the Router If You Need More Information OL-11497-03