GRP Ethernet Interfaces | Cisco Systems 12406, 12006 guide

Chapter 3 Installing the Router

Configuration Changes

•Protocols to be configured

To obtain this information, consult your network administrator. For additional interface configuration information for the RP and each of the line cards installed in your router, refer to the configuration note that shipped with each card.

GRP Ethernet Interfaces

The RJ-45 and MII receptacles on the faceplate of the GRP are IEEE

802.3u-compliant interfaces. These IEEE interfaces provide connectivity to Ethernet networks. You can use either interface, but not both at the same time.

The following configuration dialog example shows the system being configured for an Ethernet interface that will use the IP network layer protocol. (The Ethernet interface does not support external routing functions.) The IP address and subnet mask value below are examples. The actual IP address and subnet mask value would be different.

Configuring interface Ethernet0:

Is this interface in use?: yes

Configure IP on this interface?: yes

IP address for this interface: 3.3.1.1

Number of bits in subnet field: 8

Class A network is 3.0.0.0, 8 subnet bits; mask is 255.888.0.0

Configure CLNS on this interface?: yes

PRP Ethernet Interfaces

The IEEE 802.3 Ethernet interfaces on the PRP allow connections to external Ethernet networks and can transmit data rates of 10 Mbps and 100 Mbps. The transmission speed of the Ethernet ports is auto-sensing by default and is user configurable.

Caution The Ethernet ports are primarily used as Telnet ports into the router, or for booting or accessing Cisco IOS software images over a network to which an Ethernet port is directly connected. Cisco Express Forwarding (CEF) functions are switched off by default for security reasons. Cisco strongly cautions you to consider the security implications of switching on CEF routing functions on these ports.

		Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide

	OL-11497-03			3-59
	OL-11497-03			3-59

Image 59

Cisco Systems 12406, 12006 manual GRP Ethernet Interfaces, PRP Ethernet Interfaces

Contents

Installing the Router Installing a Router Tools and Equipment Required Installing the Rack-Mount Brackets OptionalInstalling the Optional Rack-Mount Brackets Installing the Optional Rack-Mount Brackets Lower and Upper Center-Mount Brackets Installing Center-Mount Brackets Optional Repeat through for both upper center-mount brackets Installing the Optional Center-Mount Brackets Power supply Installing the Chassis in a Rack OL-11497-03 Supplemental Bonding and Grounding Connections Installing the Chassis on a Tabletop or Flat Surface Supplemental Bonding and Grounding Port for Nebs Compliance Crimping the Lug Connecting RP and Line Card Cables Chassis Cable-Management Bracket Connecting Alarm Card Cables GRP Console and Auxiliary Ports Connecting to the Console and Auxiliary Ports GRP Console DCE and Auxiliary DTE Port Connections Pin Signal Input/Output Description GRP Console Port SignalsGRP Auxiliary Port Signals RTS PRP Console and Auxiliary Port Connections PRP Console and Auxiliary Ports Console Port Pin Signal Input/Output Description PRP Console Port Signals Auxiliary Port Pin Signal Installing a Flash Memory CardPRP Auxiliary Port Signals 10 Flash Memory Card Slot Opening 11 RJ-45 and MII Ethernet Connections Connecting the GRP to an Ethernet Network MDC Pin1 Out Input/Output Description Code Pin Pin Out Input/Output Description Code Pin Signal Connecting the PRP to an Ethernet Network 14 Using the Ethernet Port on the PRP PRP Ethernet Connections Ethernet Port Pin Signal Description Crossover Cable Pinout for Connecting Two PRPs Parameter Connecting to an AC Power SourceParameter RJ-45 Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm Cisco IOS Software Images IOS Software Configuration for the Router Conditions to Check Before System Startup Starting the Router and Observing Initial Conditions Overview of the Boot Process OL-11497-03 Display Meaning Source RP Alphanumeric LED RP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH External Network Interface System Configuration Dialogue Dir slot0 Manually Booting the SystemDir bootflash Locating a Valid Cisco IOS Software Image Command Description Booting from the Cisco IOS Software Image Before You Begin Router ConfigurationSetup Command Cisco IOS User Interface User Interface Command ModesGlobal Configuration Mode Privileged Exec Mode User Exec Mode ROM Monitor Mode Interface Configuration ModeSubinterface Configuration Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Host Name Configuring Global ParametersPasswords Protocols Configuring Network Interfaces PRP Ethernet Interfaces GRP Ethernet Interfaces Line Card Interfaces Router# show version Show version CommandChecking the Software Version Router# show running-config Verifying the Running Configuration SettingsShow running Config Command Example No service tcp-small-servers Hostname Router Router# copy running-config startup-config Saving the Running Configuration Settings to NvramReviewing the Running Configuration Settings Show startup-config Command No logging trap Installing the Flash Memory Card in a RP Using Flash Memory Cards in the RP Formatting a Flash Memory Card Removing the Flash Memory Card from an RP Router# format slot0 Specify a Boot ImageRouter# configure terminal Router# cd slot1 Flash Memory Console Commands Router# delete slot0info Router# cd bootflash Router# squeeze slot0 Copying Files Booting from Flash MemoryRouterconfig# boot system flash devicefilename Routerconfig# config-reg Ctrl-Z Router# copy tftpmyfile1 slot0myfile1 Router# copy tftpfilename bootflashslot0slot1 filename Router# copy tftpnew.image slot0new.image Copying a Cisco IOS Software Image Copying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Copy startup-config slot0 slot1filename Router# show bootvar Router# dir slot0 Router# copy startup-config slot0myfile2 Router# copy running-config slot0myfile2 Copy running-config slot0slot1filename Router# copy startup-config running-config Copy slot0slot1filename startup-configRouter# copy slot0myfile startup-config Locked Blocks in Flash Memory Cards If You Need More Information Installing the Router If You Need More Information OL-11497-03