Router Power Combination | Cisco Systems 12006, 12406 manual

Chapter 3 Installing the Router

Connecting to an AC Power Source

Caution The AC-input power supply weighs 14 pounds (6.4 kilograms). Use two hands when handling a power supply.

Warning The AC-input power supply power standby switch should be in the OFF position.

When operating your router on a power source, the power supply bays must have one of the following power combinations installed before operating the router:

Table 3-10	Required Power Combinations

Router Power		Combination

AC power		1	AC-input power supply
		1 power supply blank

		2	AC-input power supplies

DC power		1	DC-input PEM
		1	PEM blank

		2	DC-input PEMs

	Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
3-30	OL-11497-03

Page 30

Image 30

Cisco Systems 12006, 12406 manual Router Power Combination

Contents

Installing the Router Installing a Router Installing the Rack-Mount Brackets Optional Installing the Optional Rack-Mount BracketsTools and Equipment Required Installing the Optional Rack-Mount Brackets Installing Center-Mount Brackets Optional Lower and Upper Center-Mount Brackets Installing the Optional Center-Mount Brackets Repeat through for both upper center-mount brackets Installing the Chassis in a Rack Power supply OL-11497-03 Installing the Chassis on a Tabletop or Flat Surface Supplemental Bonding and Grounding Connections Supplemental Bonding and Grounding Port for Nebs Compliance Connecting RP and Line Card Cables Crimping the Lug Chassis Cable-Management Bracket Connecting Alarm Card Cables Connecting to the Console and Auxiliary Ports GRP Console and Auxiliary Ports GRP Console DCE and Auxiliary DTE Port Connections GRP Console Port Signals GRP Auxiliary Port SignalsPin Signal Input/Output Description RTS PRP Console and Auxiliary Ports PRP Console and Auxiliary Port Connections PRP Console Port Signals Console Port Pin Signal Input/Output Description Installing a Flash Memory Card PRP Auxiliary Port SignalsAuxiliary Port Pin Signal 10 Flash Memory Card Slot Opening Connecting the GRP to an Ethernet Network 11 RJ-45 and MII Ethernet Connections Pin1 Out Input/Output Description Code MDC Pin Out Input/Output Description Code Pin Connecting the PRP to an Ethernet Network Pin Signal 14 Using the Ethernet Port on the PRP Ethernet Port Pin Signal Description PRP Ethernet Connections Crossover Cable Pinout for Connecting Two PRPs Connecting to an AC Power Source Parameter RJ-45Parameter Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm IOS Software Configuration for the Router Cisco IOS Software Images Conditions to Check Before System Startup Overview of the Boot Process Starting the Router and Observing Initial Conditions OL-11497-03 RP Alphanumeric LED Display Meaning Source RP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH System Configuration Dialogue External Network Interface Locating a Valid Cisco IOS Software Image Manually Booting the SystemDir bootflash Dir slot0 Booting from the Cisco IOS Software Image Command Description Router Configuration Setup CommandBefore You Begin User Interface Command Modes Global Configuration ModeCisco IOS User Interface User Exec Mode Privileged Exec Mode Interface Configuration Mode Subinterface Configuration ModeROM Monitor Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Configuring Global Parameters PasswordsHost Name Configuring Network Interfaces Protocols GRP Ethernet Interfaces PRP Ethernet Interfaces Line Card Interfaces Show version Command Checking the Software VersionRouter# show version Verifying the Running Configuration Settings Show running Config Command ExampleRouter# show running-config No service tcp-small-servers Hostname Router Show startup-config Command Saving the Running Configuration Settings to NvramReviewing the Running Configuration Settings Router# copy running-config startup-config No logging trap Using Flash Memory Cards in the RP Installing the Flash Memory Card in a RP Removing the Flash Memory Card from an RP Formatting a Flash Memory Card Specify a Boot Image Router# configure terminalRouter# format slot0 Flash Memory Console Commands Router# cd slot1 Router# cd bootflash Router# delete slot0info Router# squeeze slot0 Routerconfig# config-reg Ctrl-Z Booting from Flash MemoryRouterconfig# boot system flash devicefilename Copying Files Router# copy tftpfilename bootflashslot0slot1 filename Router# copy tftpmyfile1 slot0myfile1 Copying a Cisco IOS Software Image Router# copy tftpnew.image slot0new.image Copying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Router# show bootvar Copy startup-config slot0 slot1filename Router# copy startup-config slot0myfile2 Router# dir slot0 Copy running-config slot0slot1filename Router# copy running-config slot0myfile2 Copy slot0slot1filename startup-config Router# copy slot0myfile startup-configRouter# copy startup-config running-config If You Need More Information Locked Blocks in Flash Memory Cards Installing the Router If You Need More Information OL-11497-03