Cisco Systems CIVS-IPC-2630V manual

Chapter 2 Getting Started

Adjusting the Video Image

or away from the camera. Take care not to pull the lens completely away from the camera.Obtain a sharp picture in both wide-angle and telephoto positions. When the focus is set as desired, use the Allen wrench to tighten the back focus hex screw.

Caution Do not manually adjust the focus or zoom for the IP camera. Attempting to manually do so may damage the IP camera lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

Figure 2-13 Adjusting the Camera Lens on the 2630 IP Dome

1

2

1Rotation wheel

2Panning lock screw

3Tilt lock screws (2)

4Back focus hex screws (3)

3

4

Step 4 Remove the analog monitor cable from the analog video output port.

Step 5 Replace the privacy shield by squeezing it to fit inside the four tabs on the camera unit.

Make sure to adjust the privacy shield inside the dome and trim ring assembly so that it does not block the lens from capturing video.

Step 6 Align the tab on the dome assembly with the opening in the base plate, press the dome assembly into place, and securing the three TORX screws

	Cisco Video Surveillance 2630 IP Dome User Guide
2-18	OL-24130-02

Image 30

Cisco Systems CIVS-IPC-2630V manual Adjusting the Camera Lens on the 2630 IP Dome

Contents

Cisco Video Surveillance 2630 IP Dome User Guide Americas Headquarters Cisco Video Surveillance 2630 IP Dome User Guide N T E N T S Iii Snmp Window Overview OrganizationVii Viii Features Features, IP Camera Overview, Physical Details, Package Contents, IP Camera Overview Physical Details Top of the 2630 IP Dome Overview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2630 IP Dome Package Contents Getting Started Before You Begin Installing the Cisco Video Surveillance 2630 IP Dome Preparing for InstallationPreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Procedure Mounting with a Conduit Base Attaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base See -1 on Attaching the Camera to the Base Plate Cisco Video Surveillance 2630 IP Dome User Guide Mounting with a Pendant Attaching the Privacy Shield and Dome OL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate Performing the Initial Setup of the IP Camera 12 Attaching the Privacy Shield and Dome Protocol//ipaddress Https//203.70.212.521024 Accessing the IP Camera WindowsHttps//192.168.0.100 Http//203.70.212.52 Adjusting the Video Image Http//203.70.212.521024 13 Adjusting the Camera Lens on the 2630 IP Dome Cleaning the IP Camera Powering the IP Camera On or OffResetting the IP Camera Reset Type Procedure Remarks OL-24130-02 Configuring and Managing the IP Camera Configuration Overview Configuration Item Explanation Guidelines for Use Reference See the Privacy Region See the Alarm I/O PortsSee the Audio Window section See the Focus/Zoom Window Navigating the Configuration Windows Snmp Device Settings Setup WindowsBasic Setup Window Option Description Option Description Advanced Setup Window Network Settings Option Bonjour Option Description IP Filter Window QoS Eapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window Administrator User List Maintenance Window Firmware Window Audio/Video Windows Video Window Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for Settings MPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video stream Video Adjustment PAL/50 Hz Options Day/Night Vision Option Description Audio Window Controls section onDuplex Talk and Listen Choose Simplex Talk Only , Half Duplex Talk or Listen , or Privacy Region WindowFocus/Zoom Window Full Duplex Talk and Listen Security Windows Initialization WindowInitialization Window, Complexity Window, Complexity Window Users Window section on Applications Windows Mail/FTP/HTTP Window Primary Smtp Server Described in the Basic Setup Window section onMail Setup Secondary Smtp Server Secondary FTP Mail BodyPrimary FTP Http Notification Motion Detection Window System-provided-name-value-pairs is the event information Event Window Clear button Event ScheduleNew Schedule Trigger Event Mail/FTP/HTTP Window section on Attachment Snmp Window Alarm Output Settings Alarm I/O Ports WindowAlarm Input Settings Manual Control Settings Status Windows System WindowSystem Status Audio Setting Audio/Video Window Network Window Syslog & Log Window Local Log Sys Log Server Log List Message ExplanationSystem log messages Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messages Video Log Window Smtp log messages Delete button Delete All button OL-24130-02 Viewing Video through the Home Window Overview Home Window Overview Home Window Digital zoom controls Home Window ControlsControl Description Audio controls IP camera controls Snapshot controlsSave For related information, see the Video Window section on Accessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing the Mjpeg Stream Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing Dual Streams H.264 + Mjpeg Accessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section on OL-24130-02 D E IN-1 IN-2 DSCP, for QoS Dual streaming IN-3 Sdram IN-4 LED IN-5 Options Overview IN-6 IN-7 IN-8