Cisco-Modem-Mgmt-Mib, Nas | Cisco Systems Dial NMS manual

Task 3—Using MRTG to Monitor and Graph Traffic Loads

About Selecting Dial OIDs

Table 14 Circuit Utilization OIDs (continued)

Variable		Base MIB and OID	Description

Time in use		CISCO-POP-MGMT-MIB	The time for each DS0.
		1.3.6.1.4.1.9.10.19.1.1.1.1.8

PPP calls		CISCO-POP-MGMT-MIB	The number of active PPP calls.
		1.3.6.1.4.1.9.10.19.1.1.5

DS0 high		CISCO-POP-MGMT-MIB	The maximum number of DS0s ever used
water mark		1.3.6.1.4.1.9.10.19.1.1.8	simultaneously.
		1.3.6.1.4.1.9.10.19.1.1.8

Table 15 Modem Information OIDs

Variable	Base MIB and OID		Description

Modems	CISCO-MODEM-MGMT-MIB		The number of modems currently available to
available	1.3.6.1.4.1.9.9.47.1.1.7		take calls.
	1.3.6.1.4.1.9.9.47.1.1.7

Average call	CISCO-MODEM-MGMT-MIB		The average call duration for each modem in the
duration	1.3.6.1.4.1.9.9.47.1.3.1.1.9		NAS.
	1.3.6.1.4.1.9.9.47.1.3.1.1.9

No answers	CISCO-MODEM-MGMT-MIB		The number of calls not answered by a modem.
	1.3.6.1.4.1.9.9.47.1.3.3.1.1

Failed Train	CISCO-MODEM-MGMT-MIB		The number of modem calls that failed to train
	1.3.6.1.4.1.9.9.47.1.3.3.1.2		up.
	1.3.6.1.4.1.9.9.47.1.3.3.1.2
			It’s normal behavior for most modems to not
			have a 100 percent success rate.

Successful	CISCO-MODEM-MGMT-MIB		The number of modem calls that successfully
train	1.3.6.1.4.1.9.9.47.1.3.3.1.3		trained up.
	1.3.6.1.4.1.9.9.47.1.3.3.1.3
			It’s normal for most modems to not have a 100
			percent success rate.

TX speed	CISCO-MODEM-MGMT-MIB		The current transmit speed (TX) of all the
	1.3.6.1.4.1.9.9.47.1.3.1.1.14		modems in the NAS.
	1.3.6.1.4.1.9.9.47.1.3.1.1.14
			If a modem does not have an active call, zero is
			returned.

RX speed	CISCO-MODEM-MGMT-MIB		The current receive speed (RX) of all the
	1.3.6.1.4.1.9.9.47.1.3.1.1.15		modems in the NAS.
	1.3.6.1.4.1.9.9.47.1.3.1.1.15
			If a modem does not have an active call, zero is
			returned.

Basic Dial NMS Implementation Guide

##

Image 55

Cisco Systems Dial NMS manual Cisco-Modem-Mgmt-Mib, Nas

Contents

Basic Dial NMS Implementation Guide Basic Dial NMS Implementation Guide Scope What is SNMPv1? What is SNMPv2?Dial NMS Service Definition Audience Enabling Snmp Task 3-Using Mrtg to Monitor and Graph Traffic LoadsTask 5-Setting Up a Web Portal for the Dial NMS Task 1-Enabling Snmp in a Cisco IOS Device Using CiscoView Task 6-Managing IP Addresses by Using DNSTask 7-Using HP OpenView to Create the Snmp Framework Task 8-Using CiscoWorks 2000 Resource Manager Essentials Contents Basic Dial NMS Implementation Guide Audience PurposeScope Convention Description ConventionsBold Technical References and Support Related Documentation and Sites Internetworking Solutions Guides Cisco Connection Online Documentation Feedback Documentation CD-ROMAcknowledgements UCD-SNMP About Snmp Managed devices What are the Basic Components of SNMP?Site Description Snmp Technology TAC Page -Network NMS What are Snmp MIBs? Vines SNMPv1 and ASN1 Data Types What is SNMPv1? SNMPv1 Protocol Operations What is SNMPv2? SNMPv2 and SMI About Snmp Management About Snmp Security Page Introduction to the Case Study Network Design for a Dial NMS Case Study Benefits of a Dial NMS THEnet Dial NMS Planning QuestionnaireNetwork Design Questions Answers Query tools MrtgCustom-based AAA Accounting tools and database Dial NMS Service Definition Show interface accounting Show versionShow running Show modem version Show snmp group ` show access-lists` show modem operational-status ` show modem connect-speeds Network Topology Network Topology for One POP Cisco AS5800 access servers Hardware Purpose Hardware Requirements101 50,000 5000 Lines / 1288 = 3.88 chassis AS5800s OIDs that are useful for operating a dial network Software RequirementsSoftware and Management Systems Purpose Uses CLI-based Snmp freeware to explore the Snmp MIBs Configuration Design Parameters Community Strings Purpose Network Name Assigned IP Subnet DescriptionNOC Snmp DEF Implementation and Operation TasksSupport Contact Phone T1 Dial-in Number Circuit ID Contract ABCPage CISCO-POP-MGMT-MIB OLD-CISCO-CHASSIS Dial Related System Management MIB II / InterfacesRFC1213-MIB Call-counters CommandEquivalent Cisco IOS Show controllers t1 Show caller Variable DescriptionShow modem Connect-speeds Show caller user Show caller ip ` UCD-SNMP About Enabling Snmp Enabling Snmp Command Purpose Conditions This command enables 14+ other commands for distinctTypes of Snmp traps. Edit this command list to include only Changes, environmental variables, and critical devicePage UCD-SNMP About Using UCD-SNMP Exploring Snmp MIBs for Dial Netwo rks Installing UCD-SNMP and Downloading Cisco MIBs Step Serial1/0/00 propPointToPointSerial Setting Up Snmp Commander About Snmp Commander Snmp Commander Tool Basic Dial NMS Implementation Guide Page About Mrtg Task 3-Using Mrtg to Monitor and Graph Traffic Loads Base MIB and OID Description About Selecting Dial OIDsCISCO-POP-MGMT-MIB NAS CISCO-MODEM-MGMT-MIB How to Inspect and Interpret Data Daily Graph DS0s and PPP Sessions in Use Monthly Graph DS0s and PPP Sessions in Use Configuration file used to create these graphs is posted at Interface Type Syntax Example Creating and Editing a Configuration File Example # purpose DS0s and Analog # purpose cpmISDNNoResource and cpmModemNoResource # purpose activeDS0s and cvpdnSessionTotal Crontab from any directory Sending Mrtg Graphs to a Web Server Mrtg Graphs Viewed by Using a Web Browser Page About Syslog Message Type Description Syslog Message Severity Level About Modem Call Records About NTP Web-Based MCR Viewer Enabling NTP on a Cisco IOS Device Travis-nas-01show ntp association Setting Up an NTP Client Server Problem Solution Troubleshooting the NTP ClientNtpq -p command Enables logging up to the debug level all eight levels Console errors or logging console warningsSpecifies the IP address of the syslog server This example, only the fourth T1 of a T3 card is shown Configuring the Syslog Daemon Daemon is not running, no ID is returned Aurora/etc -tail -f /var/log/router.log Inspecting Syslog Messages in t he Log File Views logs on a File//var/log/router.log Local host Generic URL Syntax Description ExamplePage Utility Function About a Web Portal Utility Function Building a Device Linker Web Device Linker Management Function Formula Example C2511-oob#clear line tty Troubleshooting a Cisco 2511 Console Connection Uses the AAA facility as an authentication method About Http Access to the CLIUsing Http to Access CLI Commands Enables the router to function as an Http server Formula Example Post the Html page that you created in to a web server Cisco IOS CLI Commander Output for the Show Caller Command Click on a CLI command and view the command output in a web About Managing IP Addresses Task 6-Managing IP Addresses by Using DNS Nrcmd zone 101.21.172.in-addr.arpa. listRR Using Cisco Network Registrar CLI Command s Opt/nwreg2/usrbin/nrcmd zone 101.21.172.in-addr.arpa. listRR Nrcmd zone the.net. addRR bobslake-nas-02 a Run the script by using the -b option Using a Batch File to Make Changes to a DNS ConfigurationFollowing output appears Creating an IP Tracker Web Creating a Primary Forward Zone IP Tracker Web Host = doc-oob-03.the.net How to Create a Reverse DNS Zone Page About HP OpenView Task 7-Using HP OpenView to Create Snmp Framework Last message Initialization complete Exit status Verifying the Snmp Configuration Object manager name snmpCollect State Click Add and Apply to submit the entries Snmp Configuration Loopback IP Address and Community Strings Performing an Snmp Demand Poll About Snmp Demand Polls Field Description Select Network Connectivity Poll Node Field Returned Value Description Testing Snmp Get RequestsConfirms the interfaces were successfully pinged You can identify the software version running on the device Verifying that Snmp Traps Are Received Troubleshooting Snmp and a Demand Poll Traps in the All Events Browser Available Interfaces and Ports for a Cisco AS5800 Unmanaging the Dial Ports Creating and Adjustin g Maps Choose Off For This Submap About Discovery FiltersGo to View Select Automatic Layout TheNetNodes TheNet Node List AS5800-1, AS5800-2 Setting Up and Editing a Discover y Filter Constituent parts Restart the netmon daemon by entering the following commands Using the Hpov CLI to Enter a Device into the DatabasePage CiscoWorks 2000 Documentation Set -A collection About CiscoWorks 2000 RMEReference CiscoWorks 2000 TAC Support Page -Provides links to Select Inventory Import from Local NMS Importing Devices from Hpov and Popul ating the Databases Devices are imported and a status summary appears Click Next Verifying that Device Polling is Turned On To accept the default settings, click Finish Status of the Devices Polling the Devices Select one or more devices Select All in the Views windowInspect the available elements for the devices Select All Devices Backing up Cisco IOS ConfigurationsSelect one or more devices from the list that appears Go to Monitor CiscoView Using CiscoViewSelect and view different system components Available Modems in the Cisco AS5800 Dial Shelf Page Http AAANTP Snmp Fcaps DNSUCD-SNMP FTP Ovw& command Ovstop commandNTP NMS FAQManaged devices Management Message types and commands MIBs Incident tracking NOC POP Touch command Troubleshooting HP OpenView Index Basic Dial NMS Implementation Guide