Cisco Systems MDS 9100 Series specs

Chapter 1 Product Overview

Supported SFP Transceivers

Combination Fibre Channel/Gigabit Ethernet SFP Transceivers

The combination Fibre Channel/Gigabit Ethernet SFP transceivers from Cisco Systems are available in SWL or LWL versions for the Cisco MDS 9140 Switch and the Cisco MDS 9120 Switch. Both versions are 1-Gbps and 2-Gbps capable.

The combination SFP transceivers from Cisco Systems have LC connectors and comply with 1-Gbps and 2-Gbps Fibre Channel as defined in FC-PI 10.0 2 and Gigabit Ethernet as defined in IEEE 802.3z.

Transmission ranges are as follows:

•Long wavelength: Up to 6.2 miles (10 km) on 9-micron single mode fiber

•Short wavelength: Up to 328 yards (300 m) on 50-micron multi-mode fiber

•Short wavelength: Up to 164 yards (150 m) on 62.5-micron multi-mode fiber For transceiver specifications, see Appendix C, “Cable and Port Specifications.”

CWDM Combination Fibre Channel/Gigabit Ethernet SFP Transceivers

All Fibre Channel and Gigabit Ethernet ports in the Cisco MDS 9100 Series support CWDM SFP transceivers.

The Cisco CWDM SFP transceivers have LC connectors and support both Gigabit Ethernet and Fibre Channel (1-Gbps / 2-Gbps). They match the wavelength plan of Cisco CWDM GBICs and Cisco CWDM optical add/drop multiplexers (OADMs).

CWDM SFP transceivers can be used in two ways:

•CWDM transmission can send and receive up to eight laser wavelengths carrying different signals simultaneously on the same optical fiber, using an OADM.

•ELWL signals can transmit over longer distances than LWL SFP transceivers.

There are eight different “colors” of CWDM SFP transceivers, one for each fixed wavelength. The fiber optic cables from the CWDM SFP transceivers must be connected to an OADM, which combines the wavelengths of the different outgoing signals into one composite send signal, and separates the received transmissions into the different wavelengths and sends them to the corresponding CWDM SFP transceiver.

For detailed transceiver specifications, see Appendix C, “Cable and Port Specifications.”

	Cisco MDS 9100 Series Hardware Installation Guide
1-14	OL-16187-01

Image 28

Cisco Systems MDS 9100 Series manual Combination Fibre Channel/Gigabit Ethernet SFP Transceivers

Contents

Cisco MDS 9100 Series Hardware Installation Guide Americas Headquarters Cisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Changed Feature Description Release Where Documented Switch Installing the Cisco MDSSwitch Port Cisco MDS 9124 Switch Specific Cisco MDS Description of the Cisco MDS 31a Installation Clearance Jumper power Jumper power cord available for Not releaseShelf Bracket Allows single-user installation Specific Kit Installation in a Telco rack Organization AudienceChapter Title Description Document Conventions Chapter Title Description Preface Regulatory Compliance and Safety Information Hardware InstallationRelated Documentation Release Notes Command-Line Interface Troubleshooting and ReferenceInstallation and Configuration Note Cisco MDS 9000 Family SSM Configuration Note Xiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 Switch Cisco MDS 9124 Switch Cisco MDS 9140 Switch Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Cisco MDS 9120 Switch Power Supplies Fan Modules Cisco MDS 9100 Series Ports Ports on the Cisco MDS 9134 SwitchPorts Port Group 6shows the Cisco MDS 9134 ports Ports on the Cisco MDS 9124 Switch Cisco MDS 9124 Ports Switch LEDs Fan module status LED 10 Cisco MDS 9124 Switch LEDs LED Status Description Supported SFP Transceivers Fibre Channel SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series Installation Options PreinstallationThis section includes the following information Installation Guidelines Unpacking and Inspecting the Switch Required Equipment Installing the Switch in a Cabinet or Rack To 36-inch slider rails To 30-inch slider railsQuantity Per kit Front-Facing Installation Description Quantity 96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Grounding the Switch Lug Starting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Removing Power Supplies Removing and Installing Power SuppliesInstalling Power Supplies Removing and Installing Fan Modules Locate the fan module in the back of the switchTo remove the existing fan module, follow these steps Slide the seating tabs toward the center of the fan module OL-16187-01 Installing a Fan Module 25shows the Cisco MDS 9134 fan module Verifying the Fan Module OL-16187-01 Connecting the Console Port Preparing for Network Connections Connecting the Console Port to a PC Connecting the Console Cable Connecting the 10/100 Ethernet Management Port Connecting a Modem to a Console Port Connecting to a Fibre Channel Port Removing and Installing SFP Transceivers Installing an SFP Transceiver SFP Transceiver with Mylar Tab Latch Removing an SFP Transceiver Removing and Installing Cables into SFP Transceivers Installing a Cable into an SFP Transceiver Connecting the LC-Type Cable to a Fibre Channel Port Removing a Cable from an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 General Requirements for Cabinets and Racks Cabinet and Rack RequirementsThis appendix includes the following information Requirements Specific to Perforated Cabinets Reference Perforated Cabinet Cisco MDS 9000 Family Telco and EIA Shelf Bracket Requirements Specific to Solid-Walled CabinetsRequirements Specific to Standard Open Racks Requirements Specific to Telco Racks Rack-Mounting Guidelines Rack Type MDS EIA 4-post45 lb 30 lb 15 lb Telco 2 post Before Installing the Shelf Brackets Installing the Shelf Bracket Kit into a Two-Post Telco RackRequired Equipment Quantity Part Description Cisco MDS 9100 Series Hardware Installation Guide Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Switch on the Shelf Brackets Statement Removing the Shelf Bracket Kit Optional OL-16187-01 Switch Specifications Description Specification Power Specifications General Power Supply Specifications AC-Input Power Supply SpecificationPower watts BTU/hr Amps AC-Input Heat Diss 85 VAC 110 VAC 220 VAC SFP Transceiver Specifications Connection Guidelines for AC-Powered SystemsCisco Fibre Channel SFP Transceivers Part Number Description Type Connector type Wavelength 850 nm 1310 nm Fiber type Description Short wavelength Long wavelength General Specifications for Cisco GE/FC SFP Transceivers Parameter Symbol Min Max UnitCisco Gigabit Ethernet/Fibre Channel Transceivers Gbps Ethernet SFP Cisco Cwdm SFP Transceivers Part Number DescriptionAdd/drop multiplexer for four Cwdm wavelengths Add/drop multiplexer for eight Cwdm wavelengths General Specifications for Cisco Cwdm SFP Transceivers Description Color Parameter Symbol Minimum Typical Maximum Units Optical Specifications for Cisco Cwdm SFP TransceiversParameter Symbol Min Typical Max Units X2 Transceiver Specifications Product Number DescriptionModal Core Size Bandwidth Maximum Cabling X2 Product Number Cable Type Microns MHz/km Distance Modal Bandwidth Maximum Cabling X2 Product NumberTransmit and Receive X2 Product Number Wavelength nm OL-16187-01 Cable and Port Specifications Cables and Adapters Console Port Pin SignalConsole Port Pinouts Signal RJ-45 Pins DB-9 Pin Mgmt 10/100 Ethernet PortRJ-45 to DB-25 Console RJ-45 to DB-9 Console Power Cords Supported Power Cords and PlugsNot used Jumper Power Cord Figure C-3 300-W Power Supply Plugs C15 C14 Site Planning and Maintenance Records Site Preparation Checklist Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4