Parameter Symbol Min Max Unit | Cisco Systems MDS 9100 Series

Appendix B Technical Specifications

SFP Transceiver Specifications

1. Approximate; actual distance may vary depending on fiber quality and other factors.

Environmental and Electrical Specifications for Cisco Fibre Channel SFP Transceivers

Table B-9provides the maximum environmental and electrical ratings for Cisco Fibre Channel SFP transceivers.

Table B-9 Maximum Environmental and Electrical Ratings for Cisco Fibre Channel SFP Transceivers

Parameter	Symbol				Min.	Max.	Unit

Storage temperature1	T	S			-40	85	°C
		S

Case temperature1, 2	T	C			0	70	°C
		C

Relative humidity1,	RH				5	95	%
Module supply voltage1,	V		CC	T,R	3.1	3.5	V
			CC

1.Absolute maximum ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short period of time. See Reliability Data Sheet for specific reliability performance.

2.Functional performance is not intended, device reliability is not implied, and damage to the device may occur over an extended period of time between absolute maximum ratings and the recommended operating conditions.

Cisco Gigabit Ethernet/Fibre Channel Transceivers

Table B-10lists the combination Gigabit Ethernet/Fibre Channel (GE/FC) SFP transceivers available through Cisco Systems for the Cisco MDS 9140 Switch and the Cisco MDS 9120 Switch.

Table B-10 Cisco Gigabit Ethernet / Fibre Channel SFP Transceivers

Part Number	Description	Type

DS-SFP-FCGE-SW	1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre	Short wavelength
	Channel–short wavelength SFP

DS-SFP-FCGE-LW	1-Gbps Ethernet and 1-Gbps/2-Gbps Fibre	Long wavelength
	Channel–long wavelength SFP

DS-SFP-GE-T	1-Gbps Ethernet SFP

General Specifications for Cisco GE/FC SFP Transceivers

Table B-11lists general specifications for Cisco combination Gigabit Ethernet/Fibre Channel SFP transceivers.

Note The cable distances provided are for 2-Gbps.

Cisco MDS 9100 Series Hardware Installation Guide

	B-6	OL-16187-01

Image 88

Cisco Systems MDS 9100 Series manual Cisco Gigabit Ethernet/Fibre Channel Transceivers, Parameter Symbol Min Max Unit

Contents

Cisco MDS 9100 Series Hardware Installation Guide Americas Headquarters Cisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Changed Feature Description Release Where Documented Switch Installing the Cisco MDSSwitch Port Cisco MDS 9124 Switch Specific Cisco MDS Description of the Cisco MDS 31a Installation Clearance Jumper power Jumper power cord available for Not releaseShelf Bracket Allows single-user installation Specific Kit Installation in a Telco rack Organization AudienceChapter Title Description Document Conventions Chapter Title Description Preface Regulatory Compliance and Safety Information Hardware InstallationRelated Documentation Release Notes Command-Line Interface Troubleshooting and ReferenceInstallation and Configuration Note Cisco MDS 9000 Family SSM Configuration Note Xiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 Switch Cisco MDS 9124 Switch Cisco MDS 9140 Switch Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Cisco MDS 9120 Switch Power Supplies Fan Modules Cisco MDS 9100 Series Ports Ports on the Cisco MDS 9134 SwitchPorts Port Group 6shows the Cisco MDS 9134 ports Ports on the Cisco MDS 9124 Switch Cisco MDS 9124 Ports Switch LEDs Fan module status LED 10 Cisco MDS 9124 Switch LEDs LED Status Description Supported SFP Transceivers Fibre Channel SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series Installation Options PreinstallationThis section includes the following information Installation Guidelines Unpacking and Inspecting the Switch Required Equipment Installing the Switch in a Cabinet or Rack To 36-inch slider rails To 30-inch slider railsQuantity Per kit Front-Facing Installation Description Quantity 96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Grounding the Switch Lug Starting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Removing Power Supplies Removing and Installing Power SuppliesInstalling Power Supplies Removing and Installing Fan Modules Locate the fan module in the back of the switchTo remove the existing fan module, follow these steps Slide the seating tabs toward the center of the fan module OL-16187-01 Installing a Fan Module 25shows the Cisco MDS 9134 fan module Verifying the Fan Module OL-16187-01 Connecting the Console Port Preparing for Network Connections Connecting the Console Port to a PC Connecting the Console Cable Connecting the 10/100 Ethernet Management Port Connecting a Modem to a Console Port Connecting to a Fibre Channel Port Removing and Installing SFP Transceivers Installing an SFP Transceiver SFP Transceiver with Mylar Tab Latch Removing an SFP Transceiver Removing and Installing Cables into SFP Transceivers Installing a Cable into an SFP Transceiver Connecting the LC-Type Cable to a Fibre Channel Port Removing a Cable from an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 General Requirements for Cabinets and Racks Cabinet and Rack RequirementsThis appendix includes the following information Requirements Specific to Perforated Cabinets Reference Perforated Cabinet Cisco MDS 9000 Family Telco and EIA Shelf Bracket Requirements Specific to Solid-Walled CabinetsRequirements Specific to Standard Open Racks Requirements Specific to Telco Racks Rack-Mounting Guidelines Rack Type MDS EIA 4-post45 lb 30 lb 15 lb Telco 2 post Before Installing the Shelf Brackets Installing the Shelf Bracket Kit into a Two-Post Telco RackRequired Equipment Quantity Part Description Cisco MDS 9100 Series Hardware Installation Guide Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Switch on the Shelf Brackets Statement Removing the Shelf Bracket Kit Optional OL-16187-01 Switch Specifications Description Specification Power Specifications General Power Supply Specifications AC-Input Power Supply SpecificationPower watts BTU/hr Amps AC-Input Heat Diss 85 VAC 110 VAC 220 VAC SFP Transceiver Specifications Connection Guidelines for AC-Powered SystemsCisco Fibre Channel SFP Transceivers Part Number Description Type Connector type Wavelength 850 nm 1310 nm Fiber type Description Short wavelength Long wavelength General Specifications for Cisco GE/FC SFP Transceivers Parameter Symbol Min Max UnitCisco Gigabit Ethernet/Fibre Channel Transceivers Gbps Ethernet SFP Cisco Cwdm SFP Transceivers Part Number DescriptionAdd/drop multiplexer for four Cwdm wavelengths Add/drop multiplexer for eight Cwdm wavelengths General Specifications for Cisco Cwdm SFP Transceivers Description Color Parameter Symbol Minimum Typical Maximum Units Optical Specifications for Cisco Cwdm SFP TransceiversParameter Symbol Min Typical Max Units X2 Transceiver Specifications Product Number DescriptionModal Core Size Bandwidth Maximum Cabling X2 Product Number Cable Type Microns MHz/km Distance Modal Bandwidth Maximum Cabling X2 Product NumberTransmit and Receive X2 Product Number Wavelength nm OL-16187-01 Cable and Port Specifications Cables and Adapters Console Port Pin SignalConsole Port Pinouts Signal RJ-45 Pins DB-9 Pin Mgmt 10/100 Ethernet PortRJ-45 to DB-25 Console RJ-45 to DB-9 Console Power Cords Supported Power Cords and PlugsNot used Jumper Power Cord Figure C-3 300-W Power Supply Plugs C15 C14 Site Planning and Maintenance Records Site Preparation Checklist Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4