Cisco Systems MDS 9100 Series specs

Appendix A Cabinet and Rack Installation

Cisco MDS 9000 Family Telco and EIA Shelf Bracket

To install the shelf brackets in a telco rack, follow these steps:

Step 1 Position a shelf bracket inside a rack-mounting rail as shown in Figure A-1and align the screw holes at the front of the shelf bracket with the holes in the rack-mounting rail. Then attach the shelf bracket to the rack-mounting rail using a minimum of four 12-24 or 10-24 screws.

Note The bottom hole of the shelf bracket should align with the bottom hole of a rack unit on the rack-mounting rail (the hole immediately above the 1/2-in. spacing).

Step 2 Repeat with the other shelf bracket.

Step 3 Verify that the shelf brackets are at the same height (using the level or tape measure as desired). Step 4 Attach the crossbar to the rear of the shelf brackets as shown in Figure A-1, using the 10-32 screws.

Cisco MDS 9100 Series Hardware Installation Guide

	A-6	OL-16187-01

Image 78

Cisco Systems manual Cisco MDS 9100 Series Hardware Installation Guide

Contents

Cisco MDS 9100 Series Hardware Installation Guide Americas Headquarters Cisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Switch Port Cisco MDS 9124 Switch Specific Changed Feature Description Release Where DocumentedSwitch Installing the Cisco MDS Cisco MDS Description of the Cisco MDS 31a Shelf Bracket Allows single-user installation Specific Installation ClearanceJumper power Jumper power cord available for Not release Kit Installation in a Telco rack Audience OrganizationChapter Title Description Document Conventions Chapter Title Description Preface Related Documentation Regulatory Compliance and Safety InformationHardware Installation Release Notes Installation and Configuration Note Command-Line InterfaceTroubleshooting and Reference Cisco MDS 9000 Family SSM Configuration Note Xiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 Switch Cisco MDS 9124 Switch Cisco MDS 9140 Switch Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Cisco MDS 9120 Switch Power Supplies Fan Modules Ports on the Cisco MDS 9134 Switch Cisco MDS 9100 Series PortsPorts Port Group 6shows the Cisco MDS 9134 ports Ports on the Cisco MDS 9124 Switch Cisco MDS 9124 Ports Switch LEDs Fan module status LED 10 Cisco MDS 9124 Switch LEDs LED Status Description Supported SFP Transceivers Fibre Channel SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series Preinstallation Installation OptionsThis section includes the following information Installation Guidelines Unpacking and Inspecting the Switch Required Equipment Quantity Installing the Switch in a Cabinet or RackTo 36-inch slider rails To 30-inch slider rails Per kit Front-Facing Installation Description Quantity 96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Grounding the Switch Lug Starting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Removing and Installing Power Supplies Removing Power SuppliesInstalling Power Supplies To remove the existing fan module, follow these steps Removing and Installing Fan ModulesLocate the fan module in the back of the switch Slide the seating tabs toward the center of the fan module OL-16187-01 Installing a Fan Module 25shows the Cisco MDS 9134 fan module Verifying the Fan Module OL-16187-01 Connecting the Console Port Preparing for Network Connections Connecting the Console Port to a PC Connecting the Console Cable Connecting the 10/100 Ethernet Management Port Connecting a Modem to a Console Port Connecting to a Fibre Channel Port Removing and Installing SFP Transceivers Installing an SFP Transceiver SFP Transceiver with Mylar Tab Latch Removing an SFP Transceiver Removing and Installing Cables into SFP Transceivers Installing a Cable into an SFP Transceiver Connecting the LC-Type Cable to a Fibre Channel Port Removing a Cable from an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 Cabinet and Rack Requirements General Requirements for Cabinets and RacksThis appendix includes the following information Requirements Specific to Perforated Cabinets Reference Perforated Cabinet Requirements Specific to Standard Open Racks Cisco MDS 9000 Family Telco and EIA Shelf BracketRequirements Specific to Solid-Walled Cabinets Requirements Specific to Telco Racks 45 lb 30 lb 15 lb Rack-Mounting GuidelinesRack Type MDS EIA 4-post Telco 2 post Required Equipment Before Installing the Shelf BracketsInstalling the Shelf Bracket Kit into a Two-Post Telco Rack Quantity Part Description Cisco MDS 9100 Series Hardware Installation Guide Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Switch on the Shelf Brackets Statement Removing the Shelf Bracket Kit Optional OL-16187-01 Switch Specifications Description Specification Power Specifications Power watts BTU/hr Amps General Power Supply SpecificationsAC-Input Power Supply Specification AC-Input Heat Diss 85 VAC 110 VAC 220 VAC Cisco Fibre Channel SFP Transceivers SFP Transceiver SpecificationsConnection Guidelines for AC-Powered Systems Part Number Description Type Connector type Wavelength 850 nm 1310 nm Fiber type Description Short wavelength Long wavelength Cisco Gigabit Ethernet/Fibre Channel Transceivers General Specifications for Cisco GE/FC SFP TransceiversParameter Symbol Min Max Unit Gbps Ethernet SFP Add/drop multiplexer for four Cwdm wavelengths Cisco Cwdm SFP TransceiversPart Number Description Add/drop multiplexer for eight Cwdm wavelengths General Specifications for Cisco Cwdm SFP Transceivers Description Color Optical Specifications for Cisco Cwdm SFP Transceivers Parameter Symbol Minimum Typical Maximum UnitsParameter Symbol Min Typical Max Units Modal Core Size Bandwidth Maximum Cabling X2 Product Number X2 Transceiver SpecificationsProduct Number Description Cable Type Microns MHz/km Distance Transmit and Receive X2 Product Number ModalBandwidth Maximum Cabling X2 Product Number Wavelength nm OL-16187-01 Cable and Port Specifications Cables and Adapters Pin Signal Console PortConsole Port Pinouts RJ-45 to DB-25 Console Signal RJ-45 Pins DB-9 PinMgmt 10/100 Ethernet Port RJ-45 to DB-9 Console Supported Power Cords and Plugs Power CordsNot used Jumper Power Cord Figure C-3 300-W Power Supply Plugs C15 C14 Site Planning and Maintenance Records Site Preparation Checklist Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4