113430 | Cisco Systems MDS 9100 Series manual

Chapter 2 Installing the Cisco MDS 9100 Series

Installing the Switch in a Cabinet with Insufficient Front Clearance

Figure 2-12 Attaching the Cisco MDS 9100 Series Switch (Rear-Facing) to the Cabinet

Front cabinet

mounting

rails

Rear cabinet

mounting

rails

a.

113430

b.Repeat for the front rack-mount bracket on the other side of the switch.

If you are installing the optional cable guides, place the cable guides in front of the front rack-mount brackets, and then pass the screws through the cable guides, front rack-mount brackets, and rear mounting rail. You can install one or both cable guides; if installing a single cable guide, it can be installed on either side.

Installing a Cisco MDS 9134 Switch or a Cisco MDS 9124 Switch Rear-Facing into Cabinet

To install a Cisco MDS 9134 Switch or a Cisco MDS 9124 Switch rear-facing into a cabinet using the rack-mount kit provided with the switch (for cabinets with insufficient front-facing clearance), follow these steps:

Step 1 Install the notched slider rails in the rack:

		Cisco MDS 9100 Series Hardware Installation Guide
		Cisco MDS 9100 Series Hardware Installation Guide
	OL-16187-01			2-17
	OL-16187-01			2-17

Image 45

Cisco Systems MDS 9100 Series manual 113430

Contents

Americas Headquarters Cisco MDS 9100 Series Hardware Installation Guide Cisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Switch Installing the Cisco MDS Changed Feature Description Release Where DocumentedSwitch Port Cisco MDS 9124 Switch Specific Cisco MDS Description of the Cisco MDS 31a Jumper power Jumper power cord available for Not release Installation ClearanceShelf Bracket Allows single-user installation Specific Kit Installation in a Telco rack Audience OrganizationChapter Title Description Chapter Title Description Document Conventions Preface Hardware Installation Regulatory Compliance and Safety InformationRelated Documentation Release Notes Troubleshooting and Reference Command-Line InterfaceInstallation and Configuration Note Cisco MDS 9000 Family SSM Configuration Note Xiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 Switch Cisco MDS 9140 Switch Cisco MDS 9124 Switch Cisco MDS 9120 Switch Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Fan Modules Power Supplies Ports on the Cisco MDS 9134 Switch Cisco MDS 9100 Series PortsPorts Port Group 6shows the Cisco MDS 9134 ports Cisco MDS 9124 Ports Ports on the Cisco MDS 9124 Switch Fan module status LED Switch LEDs 10 Cisco MDS 9124 Switch LEDs Status Description LED Fibre Channel SFP Transceivers Supported SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series Preinstallation Installation OptionsThis section includes the following information Installation Guidelines Required Equipment Unpacking and Inspecting the Switch To 36-inch slider rails To 30-inch slider rails Installing the Switch in a Cabinet or RackQuantity Per kit Description Quantity Front-Facing Installation 96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Lug Grounding the Switch Starting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Removing and Installing Power Supplies Removing Power SuppliesInstalling Power Supplies Locate the fan module in the back of the switch Removing and Installing Fan ModulesTo remove the existing fan module, follow these steps Slide the seating tabs toward the center of the fan module OL-16187-01 25shows the Cisco MDS 9134 fan module Installing a Fan Module Verifying the Fan Module OL-16187-01 Preparing for Network Connections Connecting the Console Port Connecting the Console Cable Connecting the Console Port to a PC Connecting a Modem to a Console Port Connecting the 10/100 Ethernet Management Port Removing and Installing SFP Transceivers Connecting to a Fibre Channel Port SFP Transceiver with Mylar Tab Latch Installing an SFP Transceiver Removing an SFP Transceiver Installing a Cable into an SFP Transceiver Removing and Installing Cables into SFP Transceivers Removing a Cable from an SFP Transceiver Connecting the LC-Type Cable to a Fibre Channel Port Maintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 Cabinet and Rack Requirements General Requirements for Cabinets and RacksThis appendix includes the following information Reference Perforated Cabinet Requirements Specific to Perforated Cabinets Requirements Specific to Solid-Walled Cabinets Cisco MDS 9000 Family Telco and EIA Shelf BracketRequirements Specific to Standard Open Racks Requirements Specific to Telco Racks Rack Type MDS EIA 4-post Rack-Mounting Guidelines45 lb 30 lb 15 lb Telco 2 post Installing the Shelf Bracket Kit into a Two-Post Telco Rack Before Installing the Shelf BracketsRequired Equipment Quantity Part Description Cisco MDS 9100 Series Hardware Installation Guide Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Shelf Bracket Kit into a Four-Post EIA Rack Statement Installing the Switch on the Shelf Brackets Removing the Shelf Bracket Kit Optional OL-16187-01 Description Specification Switch Specifications Power Specifications AC-Input Power Supply Specification General Power Supply SpecificationsPower watts BTU/hr Amps AC-Input Heat Diss 85 VAC 110 VAC 220 VAC Connection Guidelines for AC-Powered Systems SFP Transceiver SpecificationsCisco Fibre Channel SFP Transceivers Part Number Description Type Description Short wavelength Long wavelength Connector type Wavelength 850 nm 1310 nm Fiber type Parameter Symbol Min Max Unit General Specifications for Cisco GE/FC SFP TransceiversCisco Gigabit Ethernet/Fibre Channel Transceivers Gbps Ethernet SFP Part Number Description Cisco Cwdm SFP TransceiversAdd/drop multiplexer for four Cwdm wavelengths Add/drop multiplexer for eight Cwdm wavelengths Description Color General Specifications for Cisco Cwdm SFP Transceivers Optical Specifications for Cisco Cwdm SFP Transceivers Parameter Symbol Minimum Typical Maximum UnitsParameter Symbol Min Typical Max Units Product Number Description X2 Transceiver SpecificationsModal Core Size Bandwidth Maximum Cabling X2 Product Number Cable Type Microns MHz/km Distance Bandwidth Maximum Cabling X2 Product Number ModalTransmit and Receive X2 Product Number Wavelength nm OL-16187-01 Cables and Adapters Cable and Port Specifications Pin Signal Console PortConsole Port Pinouts Mgmt 10/100 Ethernet Port Signal RJ-45 Pins DB-9 PinRJ-45 to DB-25 Console RJ-45 to DB-9 Console Supported Power Cords and Plugs Power CordsNot used Figure C-3 300-W Power Supply Plugs Jumper Power Cord C15 C14 Site Preparation Checklist Site Planning and Maintenance Records Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4