Cisco Cwdm SFP Transceivers | Cisco Systems MDS 9100 Series guide

Appendix B Technical Specifications

SFP Transceiver Specifications

Table B-11 General Specifications for Cisco Gigabit Ethernet/Fibre Channel SFP Transceivers

Description	Short wavelength		Long wavelength

Connector type	LC		LC

Wavelength	850 nm		1310 nm

Fiber type	MMF		SMF

Core size	50 microns	62.5 microns	9/125 microns

Cable distance1	300 m	150 m	10 km
Transmit power	-1.5 to -9.5 dBm		-3 to -9.5 dBm

1. Approximate; actual distance may vary depending on fiber quality and other factors.

Environmental and Electrical Specifications for Cisco GE/FC SFP Transceivers

Table B-12provides the maximum environmental and electrical ratings for Cisco GE/FC SFP transceivers.

Table B-12 Maximum Environmental and Electrical Ratings for Cisco GE/FC SFP Transceivers

Parameter	Symbol				Min.	Max.	Unit

Storage temperature1	T	S			-40	100	°C
		S

Case temperature1, 2	T	C			0	85	°C
		C

Relative humidity1	RH				5	95	%
Module supply voltage1	V		CC	T,R	3.1	3.5	V
			CC

1.Absolute maximum ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short period of time. See Reliability Data Sheet for specific reliability performance.

2.Functional performance is not intended, device reliability is not implied, and damage to the device may occur over an extended period of time between absolute maximum ratings and the recommended operating conditions.

Cisco CWDM SFP Transceivers

Table B-13lists the CWDM SFP transceivers available through Cisco Systems. These SFP transceivers are supported by the Cisco MDS 9140 and Cisco MDS 9120 switch.

Table B-13 Cisco CWDM SFP Transceivers

Part Number	Description

DS-CWDM-xxxx	Gigabit Ethernet and 1-Gbps/2-Gbps/4-Gbps Fibre Channel SFP LC interface
	xxxx where xxxx = 1470, 1490, 1510, 1530, 1550, 1570, 1590, or 1610 nm.

DS-CWDM-MUX-4	Add/drop multiplexer for four CWDM wavelengths.

DS-CWDM-MUX-8	Add/drop multiplexer for eight CWDM wavelengths.

DS-CWDMCHASSIS	Two slot chassis for CWDM add/drop multiplexers.

Cisco MDS 9100 Series Hardware Installation Guide

	OL-16187-01	B-7

Image 89

Cisco Systems MDS 9100 Series manual Cisco Cwdm SFP Transceivers, Part Number Description

Contents

Americas Headquarters Cisco MDS 9100 Series Hardware Installation Guide Cisco MDS 9100 Series Hardware Installation Guide N T E N T S Preinstallation Cabinet and Rack Requirements A-1 Cables and Adapters C-1 Console Port C-2 Switch Installing the Cisco MDS Changed Feature Description Release Where DocumentedSwitch Port Cisco MDS 9124 Switch Specific Cisco MDS Description of the Cisco MDS 31a Jumper power Jumper power cord available for Not release Installation ClearanceShelf Bracket Allows single-user installation Specific Kit Installation in a Telco rack Chapter Title Description AudienceOrganization Chapter Title Description Document Conventions Preface Hardware Installation Regulatory Compliance and Safety InformationRelated Documentation Release Notes Troubleshooting and Reference Command-Line InterfaceInstallation and Configuration Note Cisco MDS 9000 Family SSM Configuration Note Xiv Product Overview Cisco MDS 9100 Series Multilayer Fabric Switches Cisco MDS 9134 Switch Cisco MDS 9134 Switch Cisco MDS 9140 Switch Cisco MDS 9124 Switch Cisco MDS 9120 Switch Cisco MDS Fibre Channel Bladeswitch for IBM BladeCenter Fan Modules Power Supplies Ports Port Group Ports on the Cisco MDS 9134 SwitchCisco MDS 9100 Series Ports 6shows the Cisco MDS 9134 ports Cisco MDS 9124 Ports Ports on the Cisco MDS 9124 Switch Fan module status LED Switch LEDs 10 Cisco MDS 9124 Switch LEDs Status Description LED Fibre Channel SFP Transceivers Supported SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP Transceivers Installing the Cisco MDS 9100 Series This section includes the following information PreinstallationInstallation Options Installation Guidelines Required Equipment Unpacking and Inspecting the Switch To 36-inch slider rails To 30-inch slider rails Installing the Switch in a Cabinet or RackQuantity Per kit Description Quantity Front-Facing Installation 96616 Installing the Slider Rails Sliding the Cisco MDS 9100 Series onto the Slider Rails 182460 Attaching the Switch to the Rack Cisco MDS 9100 Series Hardware Installation Guide Front rack-mount bracket Bracket Series Front cabinet Mounting rails Rear cabinet mounting Rails Front cabinet Mounting Rails Rear cabinet 113430 182462 Rear cabinet Mounting Rails Front cabinet 182466 182464 270195 Lug Grounding the Switch Starting Up the Switch Installing the Cisco MDS 9100 Series Starting Up the Switch Removing and Installing Components Power module Fan Module Power modules Fan modules Installing Power Supplies Removing and Installing Power SuppliesRemoving Power Supplies Locate the fan module in the back of the switch Removing and Installing Fan ModulesTo remove the existing fan module, follow these steps Slide the seating tabs toward the center of the fan module OL-16187-01 25shows the Cisco MDS 9134 fan module Installing a Fan Module Verifying the Fan Module OL-16187-01 Preparing for Network Connections Connecting the Console Port Connecting the Console Cable Connecting the Console Port to a PC Connecting a Modem to a Console Port Connecting the 10/100 Ethernet Management Port Removing and Installing SFP Transceivers Connecting to a Fibre Channel Port SFP Transceiver with Mylar Tab Latch Installing an SFP Transceiver Removing an SFP Transceiver Installing a Cable into an SFP Transceiver Removing and Installing Cables into SFP Transceivers Removing a Cable from an SFP Transceiver Connecting the LC-Type Cable to a Fibre Channel Port Maintaining SFP Transceivers and Fiber-Optic Cables OL-16187-01 This appendix includes the following information Cabinet and Rack RequirementsGeneral Requirements for Cabinets and Racks Reference Perforated Cabinet Requirements Specific to Perforated Cabinets Requirements Specific to Solid-Walled Cabinets Cisco MDS 9000 Family Telco and EIA Shelf BracketRequirements Specific to Standard Open Racks Requirements Specific to Telco Racks Rack Type MDS EIA 4-post Rack-Mounting Guidelines45 lb 30 lb 15 lb Telco 2 post Installing the Shelf Bracket Kit into a Two-Post Telco Rack Before Installing the Shelf BracketsRequired Equipment Quantity Part Description Cisco MDS 9100 Series Hardware Installation Guide Figure A-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Shelf Bracket Kit into a Four-Post EIA Rack Statement Installing the Switch on the Shelf Brackets Removing the Shelf Bracket Kit Optional OL-16187-01 Description Specification Switch Specifications Power Specifications AC-Input Power Supply Specification General Power Supply SpecificationsPower watts BTU/hr Amps AC-Input Heat Diss 85 VAC 110 VAC 220 VAC Connection Guidelines for AC-Powered Systems SFP Transceiver SpecificationsCisco Fibre Channel SFP Transceivers Part Number Description Type Description Short wavelength Long wavelength Connector type Wavelength 850 nm 1310 nm Fiber type Parameter Symbol Min Max Unit General Specifications for Cisco GE/FC SFP TransceiversCisco Gigabit Ethernet/Fibre Channel Transceivers Gbps Ethernet SFP Part Number Description Cisco Cwdm SFP TransceiversAdd/drop multiplexer for four Cwdm wavelengths Add/drop multiplexer for eight Cwdm wavelengths Description Color General Specifications for Cisco Cwdm SFP Transceivers Parameter Symbol Min Typical Max Units Optical Specifications for Cisco Cwdm SFP TransceiversParameter Symbol Minimum Typical Maximum Units Product Number Description X2 Transceiver SpecificationsModal Core Size Bandwidth Maximum Cabling X2 Product Number Cable Type Microns MHz/km Distance Bandwidth Maximum Cabling X2 Product Number ModalTransmit and Receive X2 Product Number Wavelength nm OL-16187-01 Cables and Adapters Cable and Port Specifications Console Port Pinouts Pin SignalConsole Port Mgmt 10/100 Ethernet Port Signal RJ-45 Pins DB-9 PinRJ-45 to DB-25 Console RJ-45 to DB-9 Console Not used Supported Power Cords and PlugsPower Cords Figure C-3 300-W Power Supply Plugs Jumper Power Cord C15 C14 Site Preparation Checklist Site Planning and Maintenance Records Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Network Information D E IN-2 IN-3 IN-4