3A1582Rev1.6 | Cooper Bussmann BU-945U-E 802.11 DSSS specification

Cooper Bussmann Wireless Ethernet & Device Server BU-945U-E 802.11 DSSS User Manual

Figure 7

When Jperf screen appears select Client Mode, enter in IP address of the Server PC; leave Port as default and press Run Iperf button. The test will run again and the Bandwidth (Throughput) display will show results of the test.

Note: Jperf runs using Java technology and depending on PC setup further installation of Java software may be required.

3A1582Rev1.6

www.cooperbussmann.com/BussmannWirelessResources

77

Image 77

Cooper Bussmann BU-945U-E 802.11 DSSS user manual 3A1582Rev1.6

Contents

Read Retain Phone 800 a.m 500 p.m. Central, M-F 636 Fax 636 Cooper Bussmann Application EngineeringFCC Notice Cooper Bussmann Important NoticeGNU Free Documentation License Contents Network Topology BU-945U-E 802.11 630mW max powerAccess Point vs Client 3A1582Rev1.6 Bridge vs. Router Getting Started Quickly General Antenna Installation Plant and Factory Installations Bench test and Demo System SetupLine-of-sight installations Antennas Omni-directional Antennas Installation tips Serial Connections Power SupplyDirectional Antennas RS232 Serial Port RS485 Serial Port DB9 Connector Pinouts 3A1582Rev1.6 Discrete Digital Input/Output Start-up 802.11 900 MHz Channels Selecting a ChannelLED Indication 3A1582Rev1.6 Data Throughput Based on Repeater Hops Radio Throughput Accessing Configuration for the First Time Configuring the Unit for the First TimeDefault Configuration Enter the username user and default password user Power up the BU-945U-E moduleMethod 1 Set PC to same network as BU-945U-E For local addresses 3A1582Rev1.6 Quick Start Quick Start Configuration Network Configuration Wireless ports will have the same IP address Dhcp Server Configuration, Default is uncheckedConfigured Essid of the client Save Changes and Reset Encryption keys must not be all zeros, i.e Security Menu 3A1582Rev1.6 Normal Operation Radio ConfigurationTransparent Bridge Operation Router Operation Signal quality, etc Bands Default is AutoDrop back to non-bursting mode Access point Radio Mode BU-945U-E Only Supports the 802.11 Standard Dhcp Client ConfigurationDefault distance is 20km Channel Selection Spanning Tree Algorithm / Redundancy Dhcp Server ConfigurationDNS Server Configuration Multiple AP Repeater Mesh Network 3A1582Rev1.6 Site B WDS Configuration Example Extending range using WDS Example Adding Redundancy Example Roaming with WDS Access Points 3A1582Rev1.6 Example WDS Routed Network Mouse, to highlight the entire row STP Routing RulesWDS Connections Information at a later time Wireless Message FilteringSpecifies a destination host 3A1582Rev1.6 Utilize the radio link. All other devices are blocked MAC Address Filter ConfigurationIP Address Filter Configuration ARP Filter Configuration RS-232 PPP Server Serial Port Configuration Serial Gateway Modbus Modbus RTU to TCP Serial Gateway Server/Client/Multicast Serial Menu Modbus TCP to RTU Gateway Multicast Pipe Manager Port on the Client, i.e., Scada, DCS, etc Digital Input/OutputMulticast Group IP Address To be the same on all communicating Multicast devices Modbus I/O Transfer 3A1582Rev1.6 Modbus TCP Configuration on I/O Transfer Menu Module Information Webpage Fields Module Information ConfigurationModbus TCP Client Mappings on I/O Transfer Menu System Tools Remote Configuration Extending a Wired Network Configuration ExamplesSetting a BU-945U-E to Factory Default Settings LAN B Configuration Client 1 ConfigurationClient 2 Configuration Extending Range of a Network with a Repeater Hop Access Point ConfigurationClient Configuration Boot Status LED Indication during Start-up Diagnostics ChartLED Indicator Condition Meaning RED Continuously Connectivity Diagnostic Information AvailableConnectivity Parameters Site Survey Network Traffic Analysis Statistics 9999 Both Reset module enter Ffff to reset module Internal Diagnostic Modbus RegistersConnection Information 5014 STA Only Statistic Registers Ping Testing Radio PathsUtilities 3A1582Rev1.6 Arp Ipconfig Route General Power SupplyRadio Transceiver Serial Ports Input / Output status System Parameters Appendix a Firmware Upgrades Web-Based Upgrade CSMA/CA ACKCSMA/CD Dhcp ISN IeeeIPX-SPX NAT SNRNIC SSL VPN VoIPWAN WEP DBm to mW Conversion Iperf Applications InstallationMaterials 3A1582Rev1.6 JPerf Application 3A1582Rev1.6 Terms and Conditions Preamble 3A1582Rev1.6 No Warranty 3A1582Rev1.6 Customer Assistance