Psrr OB | Cypress CY8CNP102B, CY8CNP102E specs

PRELIMINARY CY8CNP102B, CY8CNP102E

DC Analog Output Buffer Specifications

Table 9. 3.3V DC Analog Output Buffer Specifications (CY8CNP102B)

Symbol	Description	Min	Typ	Max	Units
VOSOB	Input Offset Voltage (Absolute Value)	–	3	12	mV
TCVOSOB	Average Input Offset Voltage Drift	–	+6	–	μV/°C
VCMOB	Common-Mode Input Voltage Range	0.5	-	Vcc - 1.0	V
ROUTOB	Output Resistance
	Power = Low	–	–	10	Ω
	Power = High	–	–	10	Ω

VOHIGHOB	High Output Voltage Swing
	(Load = 1KΩ to Vcc/2)
	Power = Low	0.5 x Vcc + 1.0	–	–	V
	Power = High	0.5 x Vcc + 1.0	–	–	V

VOLOWOB	Low Output Voltage Swing
	(Load = 1KΩ to Vcc/2)
	Power = Low	–	–	0.5 x Vcc - 1.0	V
	Power = High	–	–	0.5 x Vcc - 1.0	V

ISOB	Supply Current Including Bias Cell
	(No Load)
	Power = Low	–	0.8	1	mA
	Power = High	–	2.0	5	mA

PSRROB	Supply Voltage Rejection Ratio	60	64	–	dB

Document #: 001-43991 Rev. *D

Page 13 of 38

[+] Feedback

Page 13

Image 13

Cypress CY8CNP102B, CY8CNP102E manual Psrr OB

Contents

Overview Features Logic Block Diagram Gpio PinoutsENW NVA1 NVWNVA2 ENA1 PSoC NV Core PSoC NV Functional OverviewNvSRAM Data Memory NvSRAM Operation Programmable Analog System Programmable Digital SystemAdditional System Resources PSoC Designer Software Subsystems Development ToolsEsigner Hardware Tools Designing with User ModulesUser Module and Source Code Development Flows Parts per million Cypress nvSRAM user ModuleMicrohenry Picosecond Microsecond Samples per second 3V Operation Operating TemperatureAbsolute Maximum Ratings ESD DC Electrical Characteristics Psrroa Cmrroa Psrr OB Capacitor Unit Value Switch Cap DC Analog Reference SpecificationsAgnd = BandGap1 Agnd = 1.6 x BandGap1 Resistor Unit Value Continuous Time PORLEV10 = 00b Vdd Value for Ppor Trip negative ramp Vdd Value for Ppor Trip positive rampPORLEV10 = 00b Ppor Hysteresis PORLEV10 = 00b Input Low Voltage During Programming or Verify Supply Current During Programming or VerifyDriving internal pull During Programming or Verify Down resistor DC24M AC Electrical Characteristics Gpio Operating Frequency 12.3 MHz Normal Strong Mode TRiseS Power Up Recall DurationStore Cycle Duration 12.5 Low Voltage Trigger Level Bwoa Spim CrcprsSpis Bwob Data Out Delay from Falling Edge of Sclk 0V ≤ Vcc ≤ Data Set up Time to Falling Edge of SclkSetup Time for a Repeated Start Condition Data Hold Time Data Setup Time 5V Operation High Output Level Vcc Capacitive Load on Pins as Input Pin dependent. Temp = 25oCCombined IOH budget Input Low Level 75 to Gross tested to 1 μA Input Capacitance Port 0 Analog Pins Input Leakage Current Port 0 Analog PinsLow power comparator LPC reference voltage range Vcc Average Input Offset Voltage Drift Psrrob PORLEV10 = 10b Ppor Hysteresis PORLEV10 = 10b Vdd Value for Ppor Trip negative rampVM20 = 011b VM20 = 100b Verify Output Low Voltage During Programming orBlock MHz Trimmed for 5V operation Using factory trim valuesSee on Internal Main Oscillator Frequency for 6 MHz Gpio Operating Frequency MHz Normal Strong Mode TRiseFVcc = 4.75V to TFallF Maximum Frequency 49.2 MHz 75V ≤ Vcc ≤ MHz due to 2 Over clocking Maximum Input Clock Frequency 24.6 MHz 75V ≤ Vcc ≤ CRC ModeSions Transmitter Maximum Input Clock Frequency 24.6 MHz Vcc ≥ 4.75V, 2 Stop Bits MHz due to 8 Over clocking 49.2 Data Out Delay from Falling Edge of Sclk 75V ≤ Vcc ≤ A b l e Switching Waveforms L e c t External Crystal Oscillator Startup Timing Diagram Ordering Information Part Numbering NomenclatureCY8CNP102B-AXI CY8CNP102E-AXI Thermal Impedance Package DiagramsTqfp 81 oC/W Pyrs Document HistoryGVCH/PYRS Worldwide Sales and Design Support Products PSoC Solutions Sales, Solutions, and Legal InformationUSB

PSRROB