5V Operation | Cypress CY8CNP102E, CY8CNP102B specification

PRELIMINARY CY8CNP102B, CY8CNP102E

5V Operation

Absolute Maximum Ratings

Table 22. 5V Absolute Maximum Ratings (CY8CNP102E)

Symbol	Description	Min	Typ	Max	Units	Notes
T	Storage Temperature	-55	25	+100	oC	Higher storage temperatures
STG						reduce data retention time.
						reduce data retention time.
						Recommended storage
						temperature is ± 25oC. Extended
						duration storage temperatures
						above 65oC degrade reliability.
T	Ambient Temperature with	-40	–	+85	oC
A	Power Applied
	Power Applied

Vcc	Supply Voltage on Vcc	-0.5	–	+6.0	V
	Relative to Vss
VIO	DC Input Voltage	Vss - 0.5	–	Vcc + 0.5	V
VIOZ	DC Voltage Applied to	Vss - 0.5	–	Vcc + 0.5	V
	Tri-state
IMIO	Maximum Current into any	-25	–	+50	mA
	Port Pin
IMAIO	Maximum Current into any	-50	–	+50	mA
	Port Pin Configured as
	Analog Driver
ESD	Electro Static Discharge	2000	–	–	V	Human Body Model ESD.
	Voltage
LU	Latch-up Current	–	–	200	mA

Operating Temperature

Table 23. 5V Operating Temperature (CY8CNP102E)

Symbol	Description	Min	Typ	Max	Units	Notes
T	Ambient Temperature	-40	–	+85	oC
A
T	Junction Temperature	-40	–	+100	oC
J

Document #: 001-43991 Rev. *D

Page 22 of 38

[+] Feedback

Image 22

Cypress CY8CNP102E, CY8CNP102B manual 5V Operation

Contents

Features Overview Logic Block Diagram Gpio PinoutsENW NVA2 NVWNVA1 ENA1 NvSRAM Data Memory PSoC NV Functional OverviewPSoC NV Core NvSRAM Operation Programmable Analog System Programmable Digital SystemAdditional System Resources PSoC Designer Software Subsystems Development ToolsEsigner Hardware Tools Designing with User ModulesUser Module and Source Code Development Flows Microhenry Picosecond Microsecond Cypress nvSRAM user ModuleParts per million Samples per second Absolute Maximum Ratings Operating Temperature3V Operation ESD DC Electrical Characteristics Cmrroa Psrroa Psrr OB Agnd = BandGap1 Agnd = 1.6 x BandGap1 DC Analog Reference SpecificationsCapacitor Unit Value Switch Cap Resistor Unit Value Continuous Time PORLEV10 = 00b Ppor Hysteresis Vdd Value for Ppor Trip positive rampPORLEV10 = 00b Vdd Value for Ppor Trip negative ramp PORLEV10 = 00b Driving internal pull Supply Current During Programming or VerifyInput Low Voltage During Programming or Verify During Programming or Verify Down resistor AC Electrical Characteristics DC24M Store Cycle Duration 12.5 Power Up Recall DurationGpio Operating Frequency 12.3 MHz Normal Strong Mode TRiseS Low Voltage Trigger Level Bwoa Spis CrcprsSpim Bwob Setup Time for a Repeated Start Condition Data Set up Time to Falling Edge of SclkData Out Delay from Falling Edge of Sclk 0V ≤ Vcc ≤ Data Hold Time Data Setup Time 5V Operation Combined IOH budget Capacitive Load on Pins as Input Pin dependent. Temp = 25oCHigh Output Level Vcc Input Low Level 75 to Low power comparator LPC reference voltage range Vcc Input Leakage Current Port 0 Analog PinsGross tested to 1 μA Input Capacitance Port 0 Analog Pins Average Input Offset Voltage Drift Psrrob VM20 = 011b PORLEV10 = 10b Vdd Value for Ppor Trip negative rampPORLEV10 = 10b Ppor Hysteresis VM20 = 100b Verify Output Low Voltage During Programming orBlock See on Using factory trim valuesMHz Trimmed for 5V operation Internal Main Oscillator Frequency for 6 MHz Vcc = 4.75V to MHz Normal Strong Mode TRiseFGpio Operating Frequency TFallF Maximum Frequency 49.2 MHz 75V ≤ Vcc ≤ Sions Transmitter Maximum Input Clock Frequency 24.6 MHz Maximum Input Clock Frequency 24.6 MHz 75V ≤ Vcc ≤ CRC ModeMHz due to 2 Over clocking Vcc ≥ 4.75V, 2 Stop Bits MHz due to 8 Over clocking 49.2 Data Out Delay from Falling Edge of Sclk 75V ≤ Vcc ≤ Switching Waveforms A b l e External Crystal Oscillator Startup Timing Diagram L e c t CY8CNP102B-AXI Part Numbering NomenclatureOrdering Information CY8CNP102E-AXI Tqfp Package DiagramsThermal Impedance 81 oC/W Pyrs Document HistoryGVCH/PYRS Worldwide Sales and Design Support Products PSoC Solutions Sales, Solutions, and Legal InformationUSB