Boot Settings screen, Network Settings screen | Dell M630 specs

Menu Item	Description

Capacity	Displays the total capacity of the hard drive. The field is undefined for
	removable media devices such as optical drives.
Port J	Sets the drive type of the selected device. For Embedded SATA settings
	in ATA mode, set this field to Auto to enable BIOS support. Set it to OFF
	to turn off BIOS support.
	For AHCI mode or RAID mode, BIOS always enables support.
Model	Displays the drive model of the selected device.
Drive Type	Displays the type of drive attached to the SATA port.
Capacity	Displays the total capacity of the hard drive. The field is undefined for
	removable media devices such as optical drives.

Boot Settings screen

You can use the Boot Settings screen to set the Boot mode to either BIOS or UEFI. It also allows you to specify the boot order.

You can view the Boot Settings screen by clicking System Setup Main Menu → System BIOS → Boot Settings.

Menu Item	Description

Boot Mode	Enables you to set the boot mode of the system.
	CAUTION: Switching the boot mode may prevent the system from
	booting if the operating system is not installed in the same boot
	mode.
	NOTE: Setting this field to UEFI disables the BIOS Boot Settings
	menu. Setting this field to BIOS disables the UEFI Boot Settings
	menu.
	If the operating system supports UEFI, you can set this option to UEFI.
	Setting this field to BIOS allows compatibility with non-UEFI operating
	systems. By default, the Boot Mode option is set to BIOS.
Boot Sequence Retry	Enables or disables the Boot Sequence Retry feature. If this field is
	enabled and the system fails to boot, the system reattempts the boot
	sequence after 30 seconds. By default, the Boot Sequence Retry option
	is set to Enabled.
Hard-Disk Failover	Specifies which devices in the Hard-Disk Drive Sequence are attempted
	in the boot sequence. When the option is Disabled, only the first hard
	disk device in the list is attempted to boot. When set to Enabled, all hard
	disk devices are attempted in order, as listed in the Hard-Disk Drive
	Sequence. This option is not enabled for UEFI Boot Mode.
Boot Option Settings	Configures the boot sequence and the boot devices.

Network Settings screen

You can use the Network Settings screen to modify PXE device settings. Network Settings are only available in UEFI boot mode. BIOS does not control network settings in the BIOS boot mode. For BIOS boot mode, the network settings are handled by the network controllers option ROM.

You can view the Network Settings screen by clicking System Setup Main Menu → System BIOS → Network Settings.

23

Image 23

Dell M630 owner manual Boot Settings screen, Network Settings screen

Contents

Dell PowerEdge M630 Page Contents Installing and removing blade components Troubleshooting your system Technical specifications 107 Getting help 112 Using System Diagnostics 102Jumpers and connectors 104 About your system Front-panel features and indicators Hard-drive/SSD indicator patterns Using USB diskette or USB DVD/CD drives Hard-drive/SSD indicators IDRAC Direct LED indicator codes IDRAC Direct LED indicator Documentation matrix Quick Resource Locator Setting up and configuring the iDRAC IP address Setting up your system Logging in to iDRAC Installing the operating system Page Navigation keys About System Setup System Bios screen Entering System SetupSystem Setup Main Menu System Memory screen System Information screen ATS Processor Settings screen Sata Settings screen Post Page Network Settings screen Boot Settings screen Integrated Devices screen 4GB Serial Communication screen C1E System Profile Settings screen System Security Settings screen Secure Boot Custom Policy Settings screen Miscellaneous Settings screen Boot Manager main menu About Boot ManagerAbout Dell Lifecycle Controller Changing the boot order Entering Boot Manager Assigning a system and/or setup password Choosing the system boot mode Using your system password to secure your system Embedded systems management Operating with a setup password enabledIDRAC Settings utility Entering the iDRAC Settings utility After working inside your system Safety instructionsRecommended tools Before working inside your system Removing the blade Removing and installing a blade Blade cover O connector cover Removing or installing the blade Installing a blade Removing the system cover Removing and installing the system cover Installing the system cover Inside the blade Inside the blade Removing the cooling shroud Cooling shroud Removing a processor/DIMM blank Installing the cooling shroudProcessor/DIMM blank Removing and installing a processor/DIMM blank Installing a processor/DIMM blank Lrdimm System memory Processor General memory module installation guidelines Advanced ECC Lockstep Mode-specific guidelines Sample memory configurations Memory configurations two processors Removing memory modules Removing the memory module Installing memory modules Module mezzanine cards Mezzanine card installation guidelines Removing the mezzanine card Removing and installing the mezzanine card Idsdm card optional Installing the mezzanine card Replacing an SD card Replacing an SD card Internal USB key Replacing the internal USB key Removing the Idsdm card Removing and installing the Idsdm card Installing the Idsdm card Removing the rSPI card RSPI card optional Replacing the SD vFlash card Installing the rSPI cardSD vFlash card Removing the Network Daughter Card Network Daughter Card NDC Processors Installing the Network Daughter Card Removing a processor Installing and removing a heat sink Processor shield opening and closing lever sequence Installing and removing a processor Installing a processorPage Applying thermal grease on the top of the processor Hard-drive/SSD bay numbering Hard drive/SSD installation guidelinesHard drives/SSDs Removing a hard drive/SSD Removing and installing a hard drive/SSD Removing a hard-drive/SSD blank Installing a hard drive/SSD Hard-drive/SSD blank Release latch Installing a hard-drive/SSD blank Hard drive/SSD Removing a 1.8 inch SSD from a 1.8 inch SSD carrier Removing the hard-drive/SSD cage Installing a 1.8 inch SSD in a 1.8 inch SSD carrier Hard-drive/SSD cage Screw Guide pin Removing the hard-drive/SSD backplane Installing the hard-drive/SSD cageHard-drive/SSD backplane Page Removing and installing the 1.8 inch x4 SSD backplane Removing the system board Installing the hard-drive/SSD backplaneSystem board Page Hex nut screw System board Screw Installing the system board Restoring the Service Tag using Easy Restore Trusted Platform Module Entering the system Service Tag using System Setup Re-enabling the TPM for BitLocker users Replacing the Nvram backup battery Nvram backup battery Replacing the Nvram backup battery Removing the PCIe extender/storage controller card Storage controller card/PCIe extender cardPage Installing the PCIe extender/storage controller card Troubleshooting your system Troubleshooting hard drives Troubleshooting USB devices Troubleshooting Solid State Drives Troubleshooting processors Troubleshooting an internal SD card Troubleshooting the Nvram backup battery Troubleshooting the blade system board Alert messages Diagnostic messagesSystem messages Running the Embedded System Diagnostics Dell Embedded System DiagnosticsWhen to use the Embedded System Diagnostics System diagnostic controls Running embedded system diagnostics from an external media System board jumper settings Jumpers and connectors CPU1 System board connectors Disabling a forgotten password Technical specifications USB Per ISO 14644-1 with a 95% upper confidence 110 Enclosure can be installed with blade Documentation feedback Locating your system Service TagContacting Dell 113