1.2.2 For VigorPro 5500G

 

 

LED

 

 

Status

 

 

Explanation

 

 

 

 

 

 

 

 

 

 

ACT (Activity)

 

 

Blinking

 

The router is powered on and running normally.

 

 

 

 

 

Off

 

The router is powered off.

 

 

Virus

 

 

On

 

The anti-virus function is enabled.

 

 

 

 

 

(Yellow)

 

 

 

 

 

IDP (Intrusion Detection and

 

On

 

The anti-intrusion function is enabled.

 

 

Prevention)

 

 

(Yellow)

 

 

 

 

 

DMZ

 

 

On

 

DMZ Host is specified in certain site.

 

 

Monitor

 

 

On

 

LAN traffic monitor is active.

 

 

VPN

 

 

On

 

The VPN tunnel is launched.

 

 

 

 

 

Off

 

The VPN tunnel is closed.

 

 

QoS

 

 

On

 

The QoS function is active.

 

 

 

 

 

 

 

 

 

 

WLAN

 

 

On

 

Wireless access point is ready.

 

 

 

 

 

Blinking

 

Ethernet packets are transmitting over wireless LAN.

 

 

 

 

 

Off

 

The WLAN function is inactive.

 

 

LED on Connector

 

 

 

 

 

 

 

 

 

10

 

On

 

The port is connected with 10Mbps.

 

 

WAN

(left LED)

 

Off

 

The port is disconnected.

 

 

 

 

Blinking

 

The data is transmitting.

 

 

 

 

 

 

 

 

 

100

 

On

 

The port is connected with 100Mbps.

 

 

 

(right LED)

 

Off

 

The port is disconnected.

 

 

 

 

 

Blinking

 

The data is transmitting.

 

 

LAN/Monitor

100

 

On

 

The port is connected with 100Mbps.

 

 

LAN

(left LED)

 

Off

 

The port is disconnected.

 

 

 

 

 

Blinking

 

The data is transmitting.

 

 

 

1000

 

On

 

The port is connected with 1000Mbps.

 

 

 

(right LED)

 

Off

 

The port is disconnected.

 

 

 

 

 

Blinking

 

The data is transmitting.

 

Interface

 

Description

 

RST

 

Restore the default settings.

 

(Factory Reset)

 

Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for

 

 

 

 

 

more than 5 seconds. When you see the ACT LED begins to blink rapidly than

 

 

 

 

 

usual, release the button. Then the router will restart with the factory default

 

 

 

 

 

configuration.

 

WAN(1/2)

 

Connecter for remote networked devices.

 

LAN/Monitor

 

Connecter for local networked devices.

 

LAN (1-4)

 

Connecter for local networked devices.

 

 

 

 

 

Connecter for a power cord with 100-240VAC (inlet).

 

 

 

 

 

 

 

 

 

 

 

Power Switch. “1” is ON; “0” is OFF.

 

 

 

 

 

 

 

 

 

 

 

 

 

VigorPro5500 Series User’s Guide

3

Page 11
Image 11
Draytek 5500 Series manual For VigorPro 5500G, Wlan