DreamGEAR MSK 33 manual

Contents

RF output	23
Headphone connection	23
Modem / RS232 interface	23
Scart socket	23
Socket TS PARALLEL (optional)	23
MEASUREMENT POSSIBILITIES	24
Level measurement	24
Maximal input level	24
SAT OPERATION	25
Sat menu	25
Entry of the transponder frequency from 00,000 MHz to16,000 MHz	25
Setting of the LNB voltage supply:	26
Selecting the LO frequency	26
Entering the transponder frequency:	26
SCAN	27
Calling up menu LNB-CONTROL	27
Switch-over of ANALOG digit. DVBS	27
Calling up the menu SAT MEASURE	27
LNB control menu	28
22 kHz control signal	28
14 V LNB supply voltage	28
18 V LNB supply voltage	28
LNB current draw	28
Checking the LNB supply voltage of a satellite receiver	29
Calling up the DiSEqC/V SEC menu	29
DiSEqC menu	30
RX assessment	30
Transmitting and receiving a DiSEqC command (TX + RX)	30
Sending a DiSEqC command (TX)	30
Entry of the hex numbers	30
RX display field	30
Submenu for entering DiSEqC commands	31
Entry	31
TX display field	31
Display field A	31
Display field B	31
Entering and transmitting a DiSEqC command	32
Simple DiSEqC	32
UFOmicro DiSEqC menu	33
General information	33
Display fields	33
RX field	33
Status field	33
Receiver field	34
TX field	34
Operating the menus	34
Installation of a UFOµ unit EXU 544 in conjunction with the MSK 33	35

5

Image 5

DreamGEAR MSK 33 manual Checking the LNB supply voltage of a satellite receiver

Contents

Operating manual Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107 Explanation of symbols General safety informationImportant Notes Validity of this manual Connections Safety InstructionsProper use Mechanical loadbearing capacity Functions Functions Function Functions overviewReturn path LP DVB-S DVB-S/C/T Front panel Displays, Operating Elements and Connections Rear panel Mains connection Mains switch DC socket Option / XLR-socketHeadphone connection TS parallel Option 10 AUX Side view MSK Observing angle of the on screen display Frequently recurring softkeys Operating ConceptScreen Menu selection General information for operationMain menu Accu CAP % I=0.00 a Mains voltage / mains switch Place of installation of the MSKOn/Off switch Safety fuse DC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat menu Sat Operation Entering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency Bargraph Level range Comment Display Switch-over of Analog digit. DvbsIII Calling up menu LNB-CONTROL LNB control menu KHz control signalLNB supply voltage LNB current draw DiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu TX display field Submenu for entering DiSEqC commandsDisplay field a Display field B Data burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC General information UFOmicro DiSEqC menuDisplay fields RX 0 E2 10 1390 Tx+rx CommandOperating the menus Modus Sat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Initial ANALOG-menu Level-dependent acoustic signalCalling up the sound subcarrier Menu Video polarity Second Anlaog menu Setting of the de-emphasis Audio carrier settingSat subcarrier menu Selecting the subcarrier recep Audio carrier table for reception type Audio carrier tables for the satellite reception 27.500 SR Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels TV menu TV OperationC10 210.25MHz A65.0dBµV Rf chan LNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Selecting the standard Analogue menuAudio carrier table for TV reception Selecting the audio carriers Measuring the current level Measuring the min./max. levelSelecting the colour standards PAL, Secam and Ntsc Measuring audio carrier spacing Mode TV Digital menuSelecting demodulation for DVB-C measurement Selecting channel bandwidths DVB-T optional Return path if menu Return Path if Menu Audio carrier table for if reception Analog menu Measurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu Measuring the min/max level FM Measure ALL Decoder operation AV MenuDecoder operation baseband Video input Video output Mpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit Screen Menu Screen setup Setting the time Click button Setting the dateSystem Menu Calls up the SYS TEM menu Saving the unit settings Saving and calling up unit settingsCalling up saved settings Copy Menu Printing out all measurements in Sat mode Printing out all measurements in TV mode Spectr Mode Menu Enlarging the videotext Text MenuHolding the videotext Original videotext size Horizontal zoom Reducing the video signal Horizontal zoom -Enlarging the video signalScope Menu Video scope menu Selecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime DiSEqC Scope Position and triggering of the DiSEqC signalSaving function Shot Cont Marker Span Spectral MenuMark Ana Marker dig Marker ana Cross-polarisation measurement on signals in SAT operation Measurement of digital signals in Sat operationZoom marker Max off Measurement of the bit error rate BER Constellation diagram for Qpsk DVB-SConst Menu Colour representation of I/Q value pairs Frontend locked Measurement of signal noise ratio SNRCarrier offset Selecting the code rate Selecting the symbol rate symbol-clockInverting /not inverting a constellation diagram Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-C Zoom Inverting /not inverting constellation diagram Examples for QAM constellation diagram Const Menu Measurement of bit error rate BER Constellation diagram DVB-T optionalMeasurement of signal noise ration SNR Carrier mode Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSK Track MVG10 Downstream measurement Upstream measurementMSK33 MVG10 RGB MSK33 Cable system With return path capable amplifiers Display of the check point Auto Measure Connection cable for modem / RS InterfacesModem / RS 232 interface Setting local echo Setting baud rateSetting hardware handshake Modem/RS232 menu TTY mode Code PasswordAnsi mode Log-in procedure Requesting help Example for logging-in in Ansi mode Interfaces List of the command abbreviations STU Loading and saving predefined settingsSTU RET LDU Maintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbon Command overview framing byte Overview of DiSEqC commandsCommand overview address byte Technical Appendix Reset Reset DiSEqC minicontroller Command overview command byte Command overview data byte DiSEqC commands for Kathrein matricesCommand for Kathrein matrix 9xx-series Command for Kathrein matrix EXR Channel and frequency table standard B/G frequency in MHz Channel tablesVHF-CCIR UHF-CCIR USB/OSB ESB VHF UHF Channel and frequency table standard Lfrequency in MHz VII Channel and frequency table standard D/K frequency in MHzViii XII Channel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socket Assignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software 9986498/0206 ZWT Subject to alterations