Loading and saving predefined settings, Stu, Ldu

Interfaces

Loading and saving predefined settings

STU	Saving of the current unit setting under a user-defined programme position number from 00-99.
	Entry:	Action:
	STU <RET>	You are asked for the programme position, under which the unit set-
		ting should be saved.
	STU 34 <RET>	Current setting is saved on the programme position 34.
LDU	Loading the setting by the	identified programme position number 00-99.
	Entry:	Action:
	LDU <RET>	You are asked for the programme position, from which the setting
		should be downloaded.
	LDU 34 <RET>	The setting is loaded from programme position 34.

Page 95

Image 95

DreamGEAR MSK 33 manual Loading and saving predefined settings, Stu Ret, Ldu Ret

Contents

Operating manual Page Preface Contents Checking the LNB supply voltage of a satellite receiver Selecting the colour standards PAL, Secam and Ntsc Mpeg transport stream interface TS-Parallel, Lvds optional Measuring an audio signal via the AV socket Scart Measurement of analogue signals in Sat operation 100 113 107 Validity of this manual General safety informationExplanation of symbols Important Notes Mechanical loadbearing capacity Safety InstructionsConnections Proper use Functions Functions DVB-S DVB-S/C/T Functions overviewFunction Return path LP Front panel Displays, Operating Elements and Connections TS parallel Option 10 AUX Mains connection Mains switch DC socket Option / XLR-socketRear panel Headphone connection Side view MSK Observing angle of the on screen display Frequently recurring softkeys Operating ConceptScreen Accu CAP % I=0.00 a General information for operationMenu selection Main menu Safety fuse Place of installation of the MSKMains voltage / mains switch On/Off switch DC socket option Accumulator and Battery OperationAccumulator operation Connections Maximal input level Measurement PossibilitiesLevel measurement Sat menu Sat Operation Entering the transponder frequency Setting of the LNB voltage supplySelecting the LO frequency Calling up menu LNB-CONTROL Switch-over of Analog digit. DvbsBargraph Level range Comment Display III LNB current draw KHz control signalLNB control menu LNB supply voltage DiSEqC Checking the LNB supply voltage of a satellite receiverCalling up the DiSEqC/V SEC menu DiSEqC menu Display field B Submenu for entering DiSEqC commandsTX display field Display field a Data burst Tone burst Example Entering and transmitting a DiSEqC commandSimple DiSEqC RX 0 E2 10 UFOmicro DiSEqC menuGeneral information Display fields Modus Tx+rx Command1390 Operating the menus Sat Operation Entering the hex numbers Sending a V-SEC command TXSEC menu Menu Level-dependent acoustic signalInitial ANALOG-menu Calling up the sound subcarrier Video polarity Second Anlaog menu Selecting the subcarrier recep Audio carrier settingSetting of the de-emphasis Sat subcarrier menu Audio carrier table for reception type Audio carrier tables for the satellite reception 27.500 SR Digital MeasurementsSAT Digital menu Level measurement Digital Min./Max. levels Rf chan TV OperationTV menu C10 210.25MHz A65.0dBµV LNB U= 0.0 V I= 0 mA TV control menuTV-DiSEqC /VSEC menu Selecting the audio carriers Analogue menuSelecting the standard Audio carrier table for TV reception Measuring audio carrier spacing Measuring the min./max. levelMeasuring the current level Selecting the colour standards PAL, Secam and Ntsc Mode TV Digital menuSelecting demodulation for DVB-C measurement Selecting channel bandwidths DVB-T optional Return path if menu Return Path if Menu Audio carrier table for if reception Analog menu Measurement of the current level Measurement of the min./max. levelMeasurement of the audio carrier spacing If RP Digital Menu QAM64 modeEntering symbol rate Radio Analog menu Radio OperationRadio menu Measuring the min/max level FM Measure ALL Video output AV MenuDecoder operation Decoder operation baseband Video input Mpeg transport stream interface TS-Parallel, Lvds optional Breaking voltageRGB operation 3sat KiKa Phoenix Mpeg Decoder Menu OptionalPAT 08 Offset 0.0 dB Setting MenuUnit Screen Menu Screen setup Calls up the SYS TEM menu Setting the dateSetting the time Click button System Menu Copy Menu Saving and calling up unit settingsSaving the unit settings Calling up saved settings Printing out all measurements in Sat mode Printing out all measurements in TV mode Spectr Mode Menu Original videotext size Text MenuEnlarging the videotext Holding the videotext Video scope menu Horizontal zoom -Enlarging the video signalHorizontal zoom Reducing the video signal Scope Menu Selecting the video line Measurement of the amplitude of the video signalMeasurement of video signals via the AV socket Scart Pos Audio ScopeTime Shot Cont Position and triggering of the DiSEqC signalDiSEqC Scope Saving function Ana Spectral MenuMarker Span Mark Marker dig Marker ana Max off Measurement of digital signals in Sat operationCross-polarisation measurement on signals in SAT operation Zoom marker Colour representation of I/Q value pairs Constellation diagram for Qpsk DVB-SMeasurement of the bit error rate BER Const Menu Frontend locked Measurement of signal noise ratio SNRCarrier offset Selecting the code rate Selecting the symbol rate symbol-clockInverting /not inverting a constellation diagram Examples for Qpsk constellation diagrams Measurement of modulation error rate MER Constellation diagram for QAM DVB-C Zoom Inverting /not inverting constellation diagram Examples for QAM constellation diagram Const Menu Carrier mode Constellation diagram DVB-T optionalMeasurement of bit error rate BER Measurement of signal noise ration SNR Hierarchy Code rate Guard Invers Frontend locked Channel display Impulse response representation Echo representation optional Measuring principle Broadband Cable Analysis Measuring System MSK Track MVG10 RGB MSK33 Upstream measurementDownstream measurement MSK33 MVG10 Cable system With return path capable amplifiers Display of the check point Auto Measure Connection cable for modem / RS InterfacesModem / RS 232 interface Modem/RS232 menu Setting baud rateSetting local echo Setting hardware handshake Log-in procedure Code PasswordTTY mode Ansi mode Requesting help Example for logging-in in Ansi mode Interfaces List of the command abbreviations LDU Loading and saving predefined settingsSTU STU RET Maintenance, Storage and Customer Service Ribbon exchange Printer paper-exchanging the ribbon Technical Appendix Overview of DiSEqC commandsCommand overview framing byte Command overview address byte Reset Reset DiSEqC minicontroller Command overview command byte Command for Kathrein matrix EXR DiSEqC commands for Kathrein matricesCommand overview data byte Command for Kathrein matrix 9xx-series USB/OSB ESB Channel tablesChannel and frequency table standard B/G frequency in MHz VHF-CCIR UHF-CCIR VHF UHF Channel and frequency table standard Lfrequency in MHz XII Channel and frequency table standard D/K frequency in MHzVII Viii Channel and frequency table standard I frequency in MHz Channel and frequency table standard M/N frequency in MHz Channel and frequency table standard M/Nfrequency in MHz Power supply Technical DataTechnical data MER SNRQpsk BER Assignment of the Scart socket AccessoriesScope of delivery TXD RXD RTS CTS DSR GND DCD DTR Assignment of RS232 socket Assignment of socket TS Parallel optional Unit variants General notes Downloading New MSK33 Operating Software 9986498/0206 ZWT Subject to alterations

Interfaces

Loading and saving predefined settings

STU

STU <RET>

LDU

LDU <RET>