Eagle Electronics Cuda 240 S/GPS specification

Trail point

Present position arrow

Navigate trail, plotter views: at left boater is heading straight toward trail point 3. Center, when the point is reached, Arrival Alarm goes off and the steering arrow points toward next trail point. At right, boater has reached point 3 and has turned northeast to follow trail to point 4.

(Flashing trail line is turned off for clarity.

Navigate trail, navigation page (compass rose) views: at left, boater is northbound heading straight toward trail point 3; bearing arrow shows the trail point straight ahead. At right, driver has reached trail point 3 and must turn northeast to follow the trail. Arrival alarm goes off and bearing arrow swings around to say turn right (northeast), to- ward the next waypoint, trail point 4. The Cuda 240 now shows naviga- tion information to point 4, which is 0.43 miles away.

Navigate a Back Trail (backtrack, or reverse)

1.Press MENUMENU↓ to MY TRAILSENT.

2.Press ↓↓ to enter the Saved Trail list, then use ↑ or ↓ to select the desired Trail NameENT.

96

Image 102

Eagle Electronics Cuda 240 S/GPS manual Navigate a Back Trail backtrack, or reverse, Trail point Present position arrow

Contents

Cuda 240 S/GPS Eagle Electronics Box Catoosa, OK USA Table of Contents Sec Sonar Troubleshooting Sec Basic GPS Operations GPS Quick Reference Sec System & GPS Setup Options 105 Sec Supplemental Material 125 127 Section Read Me First General Current drain GPS How Your Sonar Works How Your GPS Works Introduction to GPS and Waas Page How to use this manual typographical conventions Arrow Keys Menu Commands KeyboardInstructions = Menu Sequences Transducer Installation Preparations Shoot-through hull installations Transom installationTrolling motor installations Selecting a Transducer Location How low should you go? Deadrise less than Strakes PadGood location Poor location Location Poor angle Shoot-thru-hull vs. Transom Mounting Transom Transducer centerline Hull bottom Transom Transducer Assembly and Mounting Dot Washers RatchetsMetal Nut washer Rubber Bolt Transom Bottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation Internal tooth washer TMB-S bracket Bolt Nut Flat washer Transducer Orientation and Fish Arches Partial fish arches Transducer aimed Too far backFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Hulls With Floatation Materials Testing Determines Best Location True bottom Second bottom Manual range settingTransducer location High speed Trolling speed Shoot-thru-hull Installation Spread epoxy here Sand this surface Power and Cable Connections In-Dash Installation Mounting the Sonar Unit In-Dash or Bracket Bracket Installation Cut along this line 107.5 82.7 156 Millimeter Inch Screw hole Power/transducer cable Cable slot Ratchet RearBracket front Portable Sonar Installation Installing the BatteriesDepress ratchets to Release Swivel base Page Tie nylon cord here Suction Cup Bolt Nut Washer Transducer Cup Hull Transducer Section Basic Sonar Operation Memory MenusMain Menu Main Menu Commands Sonar Menu Commands Pages Page Basic Sonar Quick Reference Sonar Operations Bait school Fish Arches Thermocline With fish To adjust sensitivity Fish Symbols vs. Full Sonar Chart To Restore Factory Settings Other Free Training Aids Page ASP Advanced Signal Processing To change the ASP level Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarms ENT To adjust and turn on the shallow alarm Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarmsent To turn off the alarm, press MENUMENU↓ to Alarmsent ↓ toPress MENUMENU↓ to Alarmsent ↓ to Sonar Alarmsent Press ↑ or ↓ until the depth is correct, then press ENT To turn the fish alarm on Chart Speed Depth Cursor Depth Range Automatic Cursor line Depth box To switch to Manual Depth Range To turn Auto Depth Range on again Fish I.D. Fish Symbols & Depths Grayline To turn the Fish I.D. feature onFishTrack To turn on FishTrack HyperScroll To turn off displayed data To change displayed data font size Ping Speed & HyperScroll Reset Options To change Ping SpeedTo turn off HyperScroll Sensitivity & Auto Sensitivity To adjust sensitivity in auto mode To adjust sensitivity in manual modeTo turn Auto Sensitivity back on Set Keel Offset Tip To change the chart mode color scheme Sonar Color ModeSonar Page & Sonar Chart Display Options Full Sonar Chart Split Zoom Sonar Chart Digital Data/Chart Sonar Simulator To adjust the Surface Clarity level Surface Clarity Zoom Pan To switch the zoomZoom & Zoom Bar To turn on the Zoom BarPage Unit operates only in demo mode Unit wont turn onUnit freezes, locks up, or operates erratically No fish arches when the Fish I.D. feature is off Noise Page Section Basic GPS Operations Keyboard Power/lights on and off Main Menu Main Menu Sonar Pages Satellite StatusPage Navigation Page Position Plotter Page GPS Quick Reference Viewing the Plotter Zoom & Cursor Arrow Keys Selecting Any Plotter Item With the CursorNavigate to Cursor Position on Plotter Cancel Navigation Find Your Current Position Find Distance From Current Position To Another Location Create a Waypoint Find Distance From Point to PointWaypoints Create Waypoint at Current Position Create Waypoint on Plotter Create Waypoint by Entering a Position Delete a Waypoint Create Waypoint by Average PositionCreate Waypoint by by Projecting a Position Select a Waypoint Find a WaypointEdit a Waypoint Waypoint Name To Find on Plotterent Navigate To a Waypoint Set Man Overboard MOB Waypoint Navigate Back to MOB Waypoint Trails Creating and Saving a Trail Visible Symbol Active symbol To Save a Trail Display a Saved Trail To turn off trail displayTo turn on trail display Navigate a Trail Edit a Trail Name Visual Trailing Navigate a Trail forwardPage Navigate a Back Trail backtrack, or reverse Trail point Present position arrow Icons Create Icon on Plotter Create Icon at Current Position Delete an Icon Routes Navigate to an IconCreate and Save a Route Page Delete a Route Edit a Route Navigate a Route Navigate a Route in Reverse Utilities Section System & GPS Setup Options Alarms Important Alarm Notes Auto Satellite Search Press MENUMENU↓ to GPS Setupent Coordinate System Selection To setup Loran TD To configure a map fix Map Fix Customize Position Customize Page DisplaysGPS Simulator Customize Plotter or Navigation Simulating Trail or Route Navigation Initialize GPS Hide GPS FeaturesPress MENUMENU↓ to GPS Setupentent Plotter Auto Zoom Plotter Orientation Overlay Data To select data for display Depth Water temp Distance to destination Pop-up Help Screen Contrast and Brightness To access the Screen menu, press MenumenuentPress MENUMENU↓ to GPS SETUPENT↓ to Position Pinningent Press Exitexit to return to the previous Set Language Set Local Time Show Waas Alarm Press MENUMENU↓ to GPS SETUPENT↓ to Show Waas AlarmSoftware Version Information Sounds and Alarm Sound Styles Track Smoothing Trail OptionsGeneral Trail Options Update Trail Option Delete All Trails Delete Trail New TrailSpecific Trail Options Units of Measure Supplemental Material FCC Compliance 126 Index Page Eagle Databases License Agreement Databases Limited Warranty Eagle Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-free Accessory Ordering Information for all countries Visit our web site