HyperScroll | Eagle Electronics Cuda 240 S/GPS specs

If you have two signals of equal size, one with gray and the other with- out, then the target with gray is the stronger signal. This helps distin- guish weeds from trees on the bottom, or fish from structure.

Grayline is adjustable. Experiment with your unit to find the Grayline setting that's best for you.

At left, Sonar Page menu with Grayline command selected.

At right, the Grayline control bar.

To adjust the Grayline level:

1.From the Sonar Page, press MENU↓ to GRAYLINEENT.

2.The Grayline Control Bar appears. Press ↓ to decrease Grayline; press ↑ to increase Grayline.

3.When it's set at the desired level, press EXIT.

HyperScroll

See the entry on Ping Speed, which controls the HyperScroll feature.

Noise Rejection

See the entry on Advanced Signal Processing in this section.

Overlay Data

To change the digital data shown on top of the sonar page:

1.Press MENU↓ to OVERLAY DATAENT.

2.Press ↓ or ↑ to select Data TypeENT.

52

Image 58

Eagle Electronics Cuda 240 S/GPS manual HyperScroll

Contents

Cuda 240 S/GPS Eagle Electronics Box Catoosa, OK USA Table of Contents Sec Sonar Troubleshooting Sec Basic GPS Operations GPS Quick Reference Sec System & GPS Setup Options 105 Sec Supplemental Material 125 127 Section Read Me First General Current drain GPS How Your Sonar Works How Your GPS Works Introduction to GPS and Waas Page How to use this manual typographical conventions Arrow Keys Keyboard Menu CommandsInstructions = Menu Sequences Transducer Installation Preparations Shoot-through hull installations Transom installationTrolling motor installations Selecting a Transducer Location Deadrise less than Strakes Pad How low should you go?Good location Poor location Location Poor angle Shoot-thru-hull vs. Transom Mounting Transom Transducer centerline Hull bottom Transom Transducer Assembly and Mounting Dot Washers RatchetsMetal Nut washer Rubber Bolt Transom Bottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation Internal tooth washer TMB-S bracket Bolt Nut Flat washer Partial fish arches Transducer aimed Too far back Transducer Orientation and Fish ArchesFull fish arch Proper transducer angle SHOOT-THRU-HULL Preparation Hulls With Floatation Materials True bottom Second bottom Manual range setting Testing Determines Best LocationTransducer location High speed Trolling speed Shoot-thru-hull Installation Spread epoxy here Sand this surface Power and Cable Connections In-Dash Installation Mounting the Sonar Unit In-Dash or Bracket Bracket Installation Cut along this line 107.5 82.7 156 Millimeter Inch Ratchet Rear Screw hole Power/transducer cable Cable slotBracket front Installing the Batteries Portable Sonar InstallationDepress ratchets to Release Swivel base Page Tie nylon cord here Suction Cup Bolt Nut Washer Transducer Cup Hull Transducer Section Basic Sonar Operation Menus MemoryMain Menu Main Menu Commands Sonar Menu Commands Pages Page Basic Sonar Quick Reference Sonar Operations Bait school Fish Arches Thermocline With fish To adjust sensitivity Fish Symbols vs. Full Sonar Chart To Restore Factory Settings Other Free Training Aids Page ASP Advanced Signal Processing To change the ASP level Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarms ENT To adjust and turn on the shallow alarm Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarmsent To turn off the alarm, press MENUMENU↓ to Alarmsent ↓ toPress MENUMENU↓ to Alarmsent ↓ to Sonar Alarmsent Press ↑ or ↓ until the depth is correct, then press ENT To turn the fish alarm on Chart Speed Depth Cursor Depth Range Automatic Cursor line Depth box To switch to Manual Depth Range To turn Auto Depth Range on again Fish I.D. Fish Symbols & Depths Grayline To turn the Fish I.D. feature onFishTrack To turn on FishTrack HyperScroll To turn off displayed data To change displayed data font size Ping Speed & HyperScroll To change Ping Speed Reset OptionsTo turn off HyperScroll Sensitivity & Auto Sensitivity To adjust sensitivity in manual mode To adjust sensitivity in auto modeTo turn Auto Sensitivity back on Set Keel Offset Tip To change the chart mode color scheme Sonar Color ModeSonar Page & Sonar Chart Display Options Full Sonar Chart Split Zoom Sonar Chart Digital Data/Chart Sonar Simulator To adjust the Surface Clarity level Surface Clarity Zoom Pan To switch the zoomZoom & Zoom Bar To turn on the Zoom BarPage Unit wont turn on Unit operates only in demo modeUnit freezes, locks up, or operates erratically No fish arches when the Fish I.D. feature is off Noise Page Section Basic GPS Operations Keyboard Power/lights on and off Main Menu Main Menu Sonar Pages Satellite StatusPage Navigation Page Position Plotter Page GPS Quick Reference Selecting Any Plotter Item With the Cursor Viewing the Plotter Zoom & Cursor Arrow KeysNavigate to Cursor Position on Plotter Cancel Navigation Find Your Current Position Find Distance From Current Position To Another Location Create a Waypoint Find Distance From Point to PointWaypoints Create Waypoint at Current Position Create Waypoint on Plotter Create Waypoint by Entering a Position Create Waypoint by Average Position Delete a WaypointCreate Waypoint by by Projecting a Position Select a Waypoint Find a WaypointEdit a Waypoint Waypoint Name To Find on Plotterent Navigate To a Waypoint Set Man Overboard MOB Waypoint Navigate Back to MOB Waypoint Trails Creating and Saving a Trail Visible Symbol Active symbol To Save a Trail To turn off trail display Display a Saved TrailTo turn on trail display Navigate a Trail Edit a Trail Name Visual Trailing Navigate a Trail forwardPage Navigate a Back Trail backtrack, or reverse Trail point Present position arrow Icons Create Icon on Plotter Create Icon at Current Position Delete an Icon Navigate to an Icon RoutesCreate and Save a Route Page Delete a Route Edit a Route Navigate a Route Navigate a Route in Reverse Utilities Section System & GPS Setup Options Alarms Important Alarm Notes Auto Satellite Search Press MENUMENU↓ to GPS Setupent Coordinate System Selection To setup Loran TD To configure a map fix Map Fix Customize Position Customize Page DisplaysGPS Simulator Customize Plotter or Navigation Simulating Trail or Route Navigation Initialize GPS Hide GPS FeaturesPress MENUMENU↓ to GPS Setupentent Plotter Auto Zoom Plotter Orientation Overlay Data To select data for display Depth Water temp Distance to destination Pop-up Help Screen Contrast and Brightness To access the Screen menu, press MenumenuentPress MENUMENU↓ to GPS SETUPENT↓ to Position Pinningent Press Exitexit to return to the previous Set Language Set Local Time Press MENUMENU↓ to GPS SETUPENT↓ to Show Waas Alarm Show Waas AlarmSoftware Version Information Sounds and Alarm Sound Styles Trail Options Track SmoothingGeneral Trail Options Update Trail Option Delete All Trails New Trail Delete TrailSpecific Trail Options Units of Measure Supplemental Material FCC Compliance 126 Index Page Eagle Databases License Agreement Databases Limited Warranty Eagle Electronics Full ONE-YEAR Warranty How to Obtain Service… Not toll-free Accessory Ordering Information for all countries Visit our web site