Track Smoothing, Trail Options | Eagle Electronics Cuda 240 S/GPS

To set Alarm Sounds: Press ↓ to ALARM SOUNDS. With the option high- lighted, press ENT to check it (turn on) and uncheck it (turn off). After the option is set, press EXITEXIT to return to the page display.

To set Alarm Volume: Press ↓ to VOLUME. Press → or ← to move the bar. The left end of the scale is low volume; the right end is high volume. Af- ter the option is set, press EXITEXIT to return to the page display.

To set Alarm Style: Press ↓ to ALARM STYLEENT. Press ↑ or ↓ to change the style, then press ENT. After the option is set, press EXITEXIT to return to the page display.

Track Smoothing

This is a factory setting on the GPS Setup menu that should always be left on. When stopped or traveling at slow speeds (such as walking or trolling), Track Smoothing prevents wandering of trails, the steering arrow, compass rose and a plotter display in track-up mode.

Track Smoothing option, turned on.

Trail Options

There are several options you can use with trails. Some affect all trails, other options can be applied to a particular trail. You can change the way trails are updated, you can display or hide trails, create a new trail, delete a trail, etc.

General Trail Options

To access the Trails Menu:

Press MENUMENU↓ to MY TRAILSENT.

121

Image 127

Eagle Electronics Cuda 240 S/GPS manual Track Smoothing, General Trail Options

Contents

Cuda 240 S/GPS Eagle Electronics Box Catoosa, OK USA Table of Contents GPS Quick Reference Sec Sonar Troubleshooting Sec Basic GPS Operations Sec System & GPS Setup Options 105 127 Sec Supplemental Material 125 Section Read Me First Current drain General GPS How Your GPS Works How Your Sonar Works Introduction to GPS and Waas Page Arrow Keys How to use this manual typographical conventions Keyboard Menu CommandsInstructions = Menu Sequences Preparations Transducer Installation Selecting a Transducer Location Transom installationTrolling motor installations Shoot-through hull installations Deadrise less than Strakes Pad How low should you go?Good location Poor location Location Poor angle Transom Transducer centerline Hull bottom Shoot-thru-hull vs. Transom Mounting Dot Transom Transducer Assembly and Mounting Bolt RatchetsMetal Nut washer Rubber Washers Bottom Hull Flat-bottom hull Deep-vee hull Transom Internal tooth washer TMB-S bracket Bolt Nut Flat washer Trolling Motor Bracket Installation Partial fish arches Transducer aimed Too far back Transducer Orientation and Fish ArchesFull fish arch Proper transducer angle Hulls With Floatation Materials SHOOT-THRU-HULL Preparation True bottom Second bottom Manual range setting Testing Determines Best LocationTransducer location High speed Trolling speed Shoot-thru-hull Installation Spread epoxy here Sand this surface Power and Cable Connections Mounting the Sonar Unit In-Dash or Bracket In-Dash Installation Cut along this line Bracket Installation Millimeter Inch 107.5 82.7 156 Ratchet Rear Screw hole Power/transducer cable Cable slotBracket front Installing the Batteries Portable Sonar InstallationDepress ratchets to Release Swivel base Page Cup Bolt Nut Washer Transducer Tie nylon cord here Suction Hull Transducer Cup Section Basic Sonar Operation Menus MemoryMain Menu Main Menu Commands Sonar Menu Commands Pages Page Basic Sonar Quick Reference Bait school Fish Arches Thermocline With fish Sonar Operations To adjust sensitivity To Restore Factory Settings Fish Symbols vs. Full Sonar Chart Other Free Training Aids Page To change the ASP level ASP Advanced Signal Processing To adjust and turn on the shallow alarm Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarms ENT Press ↑ or ↓ until the depth is correct, then press ENT To turn off the alarm, press MENUMENU↓ to Alarmsent ↓ toPress MENUMENU↓ to Alarmsent ↓ to Sonar Alarmsent Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarmsent To turn the fish alarm on Depth Cursor Chart Speed Cursor line Depth box Depth Range Automatic To turn Auto Depth Range on again To switch to Manual Depth Range Fish I.D. Fish Symbols & Depths To turn on FishTrack To turn the Fish I.D. feature onFishTrack Grayline HyperScroll To change displayed data font size To turn off displayed data Ping Speed & HyperScroll To change Ping Speed Reset OptionsTo turn off HyperScroll Sensitivity & Auto Sensitivity To adjust sensitivity in manual mode To adjust sensitivity in auto modeTo turn Auto Sensitivity back on Tip Set Keel Offset Full Sonar Chart Sonar Color ModeSonar Page & Sonar Chart Display Options To change the chart mode color scheme Digital Data/Chart Split Zoom Sonar Chart Sonar Simulator Surface Clarity To adjust the Surface Clarity level To turn on the Zoom Bar To switch the zoomZoom & Zoom Bar Zoom PanPage Unit wont turn on Unit operates only in demo modeUnit freezes, locks up, or operates erratically No fish arches when the Fish I.D. feature is off Noise Page Keyboard Section Basic GPS Operations Main Menu Power/lights on and off Main Menu Satellite Status Sonar PagesPage Navigation Page Position Plotter Page GPS Quick Reference Selecting Any Plotter Item With the Cursor Viewing the Plotter Zoom & Cursor Arrow KeysNavigate to Cursor Position on Plotter Cancel Navigation Find Distance From Current Position To Another Location Find Your Current Position Create Waypoint at Current Position Find Distance From Point to PointWaypoints Create a Waypoint Create Waypoint by Entering a Position Create Waypoint on Plotter Create Waypoint by Average Position Delete a WaypointCreate Waypoint by by Projecting a Position Waypoint Name Find a WaypointEdit a Waypoint Select a Waypoint To Find on Plotterent Navigate To a Waypoint Navigate Back to MOB Waypoint Set Man Overboard MOB Waypoint Creating and Saving a Trail Trails To Save a Trail Visible Symbol Active symbol To turn off trail display Display a Saved TrailTo turn on trail display Edit a Trail Name Navigate a Trail Navigate a Trail forward Visual TrailingPage Trail point Present position arrow Navigate a Back Trail backtrack, or reverse Create Icon on Plotter Icons Delete an Icon Create Icon at Current Position Navigate to an Icon RoutesCreate and Save a Route Page Delete a Route Navigate a Route Edit a Route Navigate a Route in Reverse Utilities Alarms Section System & GPS Setup Options Auto Satellite Search Important Alarm Notes Coordinate System Selection Press MENUMENU↓ to GPS Setupent To setup Loran TD Map Fix To configure a map fix Customize Plotter or Navigation Customize Page DisplaysGPS Simulator Customize Position Simulating Trail or Route Navigation Plotter Auto Zoom Hide GPS FeaturesPress MENUMENU↓ to GPS Setupentent Initialize GPS Overlay Data Plotter Orientation To select data for display Depth Water temp Distance to destination Pop-up Help Press Exitexit to return to the previous To access the Screen menu, press MenumenuentPress MENUMENU↓ to GPS SETUPENT↓ to Position Pinningent Screen Contrast and Brightness Set Local Time Set Language Press MENUMENU↓ to GPS SETUPENT↓ to Show Waas Alarm Show Waas AlarmSoftware Version Information Sounds and Alarm Sound Styles Trail Options Track SmoothingGeneral Trail Options Delete All Trails Update Trail Option New Trail Delete TrailSpecific Trail Options Units of Measure Supplemental Material FCC Compliance 126 Index Page Eagle Databases License Agreement Databases Limited Warranty Eagle Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service… Accessory Ordering Information for all countries Visit our web site