FishTrack, Grayline | Eagle Electronics Cuda 240 S/GPS specification

To turn the Fish I.D. feature on:

1.From the Sonar Page, press MENU↓ to SONAR FEATURESENT.

2.Press ↓ to FISH ID SYMBOLSENTEXITEXIT.

To turn off Fish I.D., repeat these instructions.

FishTrack

The FishTrack feature shows the depth of a fish symbol when it ap- pears on the display. This lets you accurately gauge the depth of tar- gets. This feature is available only when the Fish I.D. feature is on. The default setting for FishTrack is off.

To turn on FishTrack:

(Note: These instructions will turn on FishTrack and Fish I.D. at the same time.)

1.From the Sonar Page, press MENU↓ to SONAR FEATURESENT.

2.Press ↓ to FISH ID DEPTHSENTEXITEXIT.

To turn off FishTrack, repeat these instructions. Turning off FishTrack in this manner will not turn off Fish I.D. symbols.

Symbols with

FishTrack depths

Sonar Features menu with Fish I.D. Depths selected. When the check box to the left is checked, the feature is on. At right, Sonar Page show- ing Fish I.D. symbols and FishTrack depths turned on.

Grayline

Grayline lets you distinguish between strong and weak echoes. It "paints" gray on targets that are stronger than a preset value. This al- lows you to tell the difference between a hard and soft bottom. For ex- ample, a soft, muddy or weedy bottom returns a weaker signal which is shown with a narrow or no gray line. a hard bottom returns a strong signal which causes a wide gray line.

51

Image 57

Eagle Electronics Cuda 240 S/GPS manual FishTrack, Grayline, To turn the Fish I.D. feature on, To turn on FishTrack

Contents

Cuda 240 S/GPS Eagle Electronics Box Catoosa, OK USA Table of Contents GPS Quick Reference Sec Sonar Troubleshooting Sec Basic GPS Operations Sec System & GPS Setup Options 105 127 Sec Supplemental Material 125 Section Read Me First Current drain General GPS How Your GPS Works How Your Sonar Works Introduction to GPS and Waas Page Arrow Keys How to use this manual typographical conventions Menu Commands KeyboardInstructions = Menu Sequences Preparations Transducer Installation Trolling motor installations Transom installationShoot-through hull installations Selecting a Transducer Location How low should you go? Deadrise less than Strakes PadGood location Poor location Location Poor angle Transom Transducer centerline Hull bottom Shoot-thru-hull vs. Transom Mounting Dot Transom Transducer Assembly and Mounting Metal Nut washer Rubber RatchetsWashers Bolt Bottom Hull Flat-bottom hull Deep-vee hull Transom Internal tooth washer TMB-S bracket Bolt Nut Flat washer Trolling Motor Bracket Installation Transducer Orientation and Fish Arches Partial fish arches Transducer aimed Too far backFull fish arch Proper transducer angle Hulls With Floatation Materials SHOOT-THRU-HULL Preparation Testing Determines Best Location True bottom Second bottom Manual range settingTransducer location High speed Trolling speed Shoot-thru-hull Installation Spread epoxy here Sand this surface Power and Cable Connections Mounting the Sonar Unit In-Dash or Bracket In-Dash Installation Cut along this line Bracket Installation Millimeter Inch 107.5 82.7 156 Screw hole Power/transducer cable Cable slot Ratchet RearBracket front Portable Sonar Installation Installing the BatteriesDepress ratchets to Release Swivel base Page Cup Bolt Nut Washer Transducer Tie nylon cord here Suction Hull Transducer Cup Section Basic Sonar Operation Memory MenusMain Menu Main Menu Commands Sonar Menu Commands Pages Page Basic Sonar Quick Reference Bait school Fish Arches Thermocline With fish Sonar Operations To adjust sensitivity To Restore Factory Settings Fish Symbols vs. Full Sonar Chart Other Free Training Aids Page To change the ASP level ASP Advanced Signal Processing To adjust and turn on the shallow alarm Press MENUMENU↓ to ALARMSENT↓ to Sonar Alarms ENT Press MENUMENU↓ to Alarmsent ↓ to Sonar Alarmsent To turn off the alarm, press MENUMENU↓ to Alarmsent ↓ toPress MENUMENU↓ to ALARMSENT↓ to Sonar Alarmsent Press ↑ or ↓ until the depth is correct, then press ENT To turn the fish alarm on Depth Cursor Chart Speed Cursor line Depth box Depth Range Automatic To turn Auto Depth Range on again To switch to Manual Depth Range Fish I.D. Fish Symbols & Depths FishTrack To turn the Fish I.D. feature onGrayline To turn on FishTrack HyperScroll To change displayed data font size To turn off displayed data Ping Speed & HyperScroll Reset Options To change Ping SpeedTo turn off HyperScroll Sensitivity & Auto Sensitivity To adjust sensitivity in auto mode To adjust sensitivity in manual modeTo turn Auto Sensitivity back on Tip Set Keel Offset Sonar Page & Sonar Chart Display Options Sonar Color ModeTo change the chart mode color scheme Full Sonar Chart Digital Data/Chart Split Zoom Sonar Chart Sonar Simulator Surface Clarity To adjust the Surface Clarity level Zoom & Zoom Bar To switch the zoomZoom Pan To turn on the Zoom BarPage Unit operates only in demo mode Unit wont turn onUnit freezes, locks up, or operates erratically No fish arches when the Fish I.D. feature is off Noise Page Keyboard Section Basic GPS Operations Main Menu Power/lights on and off Main Menu Satellite Status Sonar PagesPage Navigation Page Position Plotter Page GPS Quick Reference Viewing the Plotter Zoom & Cursor Arrow Keys Selecting Any Plotter Item With the CursorNavigate to Cursor Position on Plotter Cancel Navigation Find Distance From Current Position To Another Location Find Your Current Position Waypoints Find Distance From Point to PointCreate a Waypoint Create Waypoint at Current Position Create Waypoint by Entering a Position Create Waypoint on Plotter Delete a Waypoint Create Waypoint by Average PositionCreate Waypoint by by Projecting a Position Edit a Waypoint Find a WaypointSelect a Waypoint Waypoint Name To Find on Plotterent Navigate To a Waypoint Navigate Back to MOB Waypoint Set Man Overboard MOB Waypoint Creating and Saving a Trail Trails To Save a Trail Visible Symbol Active symbol Display a Saved Trail To turn off trail displayTo turn on trail display Edit a Trail Name Navigate a Trail Navigate a Trail forward Visual TrailingPage Trail point Present position arrow Navigate a Back Trail backtrack, or reverse Create Icon on Plotter Icons Delete an Icon Create Icon at Current Position Routes Navigate to an IconCreate and Save a Route Page Delete a Route Navigate a Route Edit a Route Navigate a Route in Reverse Utilities Alarms Section System & GPS Setup Options Auto Satellite Search Important Alarm Notes Coordinate System Selection Press MENUMENU↓ to GPS Setupent To setup Loran TD Map Fix To configure a map fix GPS Simulator Customize Page DisplaysCustomize Position Customize Plotter or Navigation Simulating Trail or Route Navigation Press MENUMENU↓ to GPS Setupentent Hide GPS FeaturesInitialize GPS Plotter Auto Zoom Overlay Data Plotter Orientation To select data for display Depth Water temp Distance to destination Pop-up Help Press MENUMENU↓ to GPS SETUPENT↓ to Position Pinningent To access the Screen menu, press MenumenuentScreen Contrast and Brightness Press Exitexit to return to the previous Set Local Time Set Language Show Waas Alarm Press MENUMENU↓ to GPS SETUPENT↓ to Show Waas AlarmSoftware Version Information Sounds and Alarm Sound Styles Track Smoothing Trail OptionsGeneral Trail Options Delete All Trails Update Trail Option Delete Trail New TrailSpecific Trail Options Units of Measure Supplemental Material FCC Compliance 126 Index Page Eagle Databases License Agreement Databases Limited Warranty Eagle Electronics Full ONE-YEAR Warranty Not toll-free How to Obtain Service… Accessory Ordering Information for all countries Visit our web site