Oxymitter 4000

Instruction Manual

IB-106-340 Rev. 3.0 December 2003

SECTION 5

STARTUP AND OPERATION

OF OXYMITTER 4000 WITH MEMBRANE KEYPAD

5-1 POWER UP

c.

Error

a.

Startup Display

 

If there is an error condition at startup, one

 

of the diagnostics LEDs will be blinking.

 

 

 

 

When power is applied to the probe, the cell

 

Refer Section 7, TROUBLESHOOTING, to

 

heater turns on. It takes approximately one

 

determine the cause of the error. Clear the

 

half hour for the cell to heat to operating

 

error, cycle power, and the operating dis-

 

temperature. This condition is indicated by

 

play should return.

 

the top four LEDs (DIAGNOSTIC ALARMS)

d.

Keypad

 

on the membrane keypad (Figure 5-1).

 

Starting with the CALIBRATION LED, the

 

The five membrane keys on the membrane

 

LEDs light in ascending order until all four

 

 

 

keypad are only used during calibration to

 

LEDs are on. At this point, all four turn off

 

 

 

adjust the high and low gas and to initiate

 

and the cycle starts again. This ramp cycle

 

 

 

the calibration sequence (Figure 5-2).

 

continues until the cell is up to operating

 

 

temperature.

 

 

b.

5-2

GENERAL OPERATION

Operating Display

a.

Overview

 

The ramp cycle turns into a cycle where the

 

 

 

 

diagnostic LEDs light in sequence from the

 

Ensure the Oxymitter 4000 is at normal op-

 

top to the bottom, one at a time. After the

 

eration. The diagnostic LEDs will display the

 

bottom LED turns on, the sequence starts

 

operating cycle. All other LEDs should be

 

again at the top with the HEATER T/C LED.

 

off.

HEATER T/C

 

HEATER T/C

 

DIAGNOSTIC

HEATER

SW2

ALARMS

O2 CELL

ON

 

 

CALIBRATION

 

CALIBRATION RECOMMENDED

HEATER

O2 CELL

CALIBRATION

TEST

POINTS

INC INC

HIGH LOW

GAS GAS

DEC DEC

O2 CELL mV +

O2 CELL mv - HEATER T/C + HEATER T/C -

CAL

TEST GAS +

PROCESS -

% O2

TP1 TP2 TP3 TP4

TP5 TP6

J1 RED YEL GRN ORG

1

2

3

4

1

2

3

4

LIGHTING SEQUENCE DURING WARM-UP

(STARTUP DISPLAY)

HEATER T/C

HEATER

O2 CELL

CALIBRATION

1

2

3

4

1

2

3

4

LIGHTING SEQUENCE DURING NORMAL OPERATION

(OPERATING DISPLAY)

22220056

Figure 5-1. Startup and Normal Operation

Rosemount Analytical Inc. A Division of Emerson Process Management

Startup and Operation with Keypad 5-1

Page 87
Image 87
Emerson 4000 manual Power UP, General Operation

4000 specifications

The Emerson 4000 is a state-of-the-art automation platform designed to enhance industrial processes and improve operational efficiency. This advanced system is recognized for its unparalleled reliability and flexibility, making it suitable for various industries such as oil and gas, chemicals, pharmaceuticals, and power generation.

One of the standout features of the Emerson 4000 is its robust architecture that comprises distributed control systems (DCS) and a comprehensive suite of software applications. This integration allows for real-time monitoring and control of complex processes, ensuring that operators have access to crucial data for informed decision-making. The system supports a wide range of field devices and protocols, facilitating seamless connectivity across various platforms.

The Emerson 4000 employs innovative technologies that elevate its performance. It incorporates advanced analytics and machine learning capabilities, which enable predictive maintenance and reduce downtime. By analyzing historical data and identifying patterns, the system can forecast potential failures, allowing operators to address issues before they escalate. This leads to increased uptime and significant cost savings.

Another key characteristic of the Emerson 4000 is its user-friendly interface. The intuitive design ensures that operators can navigate the system with ease, reducing training time and enhancing productivity. The customizable dashboards provide real-time insights and facilitate quick access to critical information, allowing teams to respond to changes in the process swiftly.

Security is also a cornerstone of the Emerson 4000 platform. The system includes multiple layers of cybersecurity measures to safeguard sensitive data and maintain the integrity of operations. This is crucial in today’s environment, where cyber threats are a significant concern for industrial facilities.

In addition, the Emerson 4000 excels in scalability. It can be easily expanded to accommodate the growing needs of a business without compromising performance. Whether an organization is looking to integrate additional processes or expand its operations geographically, the Emerson 4000 is designed to adapt and grow alongside the business.

Overall, the Emerson 4000 stands out as a powerful tool for industrial automation. Its combination of reliability, advanced technology, user-friendliness, security, and scalability makes it an ideal choice for organizations seeking to optimize their operations and drive efficiency in an increasingly competitive landscape.