Ordering Information, Code Options | Emerson 54e pH/ORP manual

MODEL 54e pH/ORP	SECTION 1.0
	DESCRIPTION AND SPECIFICATIONS

1.4 ORDERING INFORMATION

The Model 54e pH/ORP Microprocessor Analyzer is housed in a rugged, NEMA 4X (IP65) epoxy- painted cast aluminum enclosure. Standard features include a back-lit dot-matrix liquid crystal display, sensor diagnostics, dual isolated outputs, and four relays. The analyzer can measure pH or ORP as configured by the user. For ISE capability, please consult the factory.

MODEL

54e pH/ORP MICROPROCESSOR ANALYZER

	CODE		OPTIONS
	01		115/230 VAC, 50/60 Hz Power
	02		24 VDC Power


	CODE		OPTIONS
	09		HART Communications Protocol
	20		Controller Outputs - PID and TPC
	54e pH/ORP		-01	-20	EXAMPLE
	54e pH/ORP		-01	-20	EXAMPLE

ACCESSORIES

PART NO. DESCRIPTION

2002577 Wall and two inch pipe mounting kit

23545-00 Panel mounting kit

23554-00 Cable glands, kit (Qty 5 of PG 13.5)

9240048-00 Stainless steel tag (specify marking)

4

Image 10

Emerson 54e pH/ORP instruction manual Ordering Information, Code Options, Part NO. Description

Contents

PH/ORP Hart Analyzer/Controller Model 54e pH/ORP Essential Instructions Electrical Shock HazardPage Model 54E PH/ORP Microprocessor Analyzer Description and SpecificationsSection Title List of Tables Appendix TitleTable No Title Table of Contents List of Figures About This Document General Description Section Description and SpecificationsDescription of Controls Relative Humidity 95%, non condensing Alarms Specifications Physical Specifications GeneralPower Current Outputs Analyzer Specifications @ 25C Recommended Sensors Code Options Ordering InformationPart NO. Description Locating the Controller Section InstallationMechanical Installation Unpacking and Inspection Panel Mounting Analog Output Wiring Section WiringPower Input Wiring Alarm Relay Output Wiring 454EPH02 PH Sensor Compatibility PH Sensor WiringTions will Result in Controller MALFUNC- Tion 454EPH01 Cable Dressing Final Electrical Check Wiring to Model Section Calibration Introduction Adjust temp 25.1 C Hold Mode OffTemperature Calibration Buffer 1 -- Wait Autocal bufferAutomatic TWO-POINT Calibration Use the arrow keys to select the correct buffer Auto buffer cal doneCalibration Notes Pt calibration done Calibrate pointPt 04.00pH 25C Manual TWO-POINT Calibration Standardize 7.01 pH SINGLE-POINT pH Calibration Output trim Temperature Compensation OptionsTemp comp Auto 59.16 mV/pH Output trim Hold ModeTrim Outputs Section Software Configuration PH Settings List Ranges Factory Settings User Settings Diagnostics Section Outline of Menu Levels Simulate tests Alarm High 14.00pHChanging Alarm Setpoints Setpoint 07.00 pH Setpoint + 06.90 pH Setpoint 7.00 pH4mA 0.00 pH 20mA 2.00 pH Changing Output Setpoints PID only MA 0.00 pH 20 mA 14.00 pH Output 1 12.00 mA OutputOutput MA +00.00 pH Testing Outputs and Alarms Alarm setpoints Output setpointsTest output Test alarm Simulated tests Test alarm 1 Open Test alarm 1 Open Display right AL2 Measure pH Display contrast Timeout On Security Caution Changing Output Parameters Control ModeDisplay Output Control Parameters Range 4-20 mAl Fault 22.00 mARange 4-20 mA Hold feature setup Fault 22.00mAOutput 2 control Output 2 setup Hold Disable feature Alarm 3 control AlarmsInterval timer Hysteresis 0.01 pH Delay 0 sec Alarm LowSetpoint 0.01 pH Delay 0 sec Relay Default None Time period 30 sec Relay default NoneSetpoint +07.00 pH URV 2.00 pH Timeout 3600 sec Alarm FaultFeed limit Disable Alarm 4 Setup Recovery 600 sec Timer DisableOn time 120 sec Interval Timer Examples Diagnostics Off DiagnosticsZero offset 60 mV Autocal Standard DiagnosticsAuto Calibration Setup Stabilize pH 0.01 pH Stabilize time 10 sec Auto Calibration Setup Standard Buffers Continuous Sensor Diagnostics Section Theory of Operation Typical set points Interval TimerSee .8 for instructions on chang- ing these setpoints Alarm Relays Time Proportional Control TPC Mode Code Normal Mode Analog Outputs Condition Definitions Controller Mode PriorityController Mode Priority Chart Action Definitions PID Control PID Control Mode CombinationsPID Control Code Measurement and Set Point Feedback Control Proportional Gain Plus Integral Reset Proportional Mode GainControl Loop Adjustment and Tuning Process Reaction Curve Method Process Reaction Curve PID Control Password Protection Section Special Procedures and FeaturesLevel 1 3 Password Privileges Custom Curve Configuring SecuritySecurity Lock all Temp coeff +.000 Solution Temperature CompensationSensor iso 07.00 pH Operate iso +07.00 pH Section Troubleshooting Troubleshooting is easy as 1, 2, 3… Diagnostic Messages Diagnostic Messages Description of problem Quick Troubleshooting Guide Symptom Action Diagnostic Variables Theoretical pH vs. Millivolt Values at 25C 77F Troubleshooting Procedure Troubleshooting GuidelinesTemperature Compensation Circuit Ohms Ambient Temperature Preamp in a junction box Figure Preamplifier Troubleshooting ProcedureController preamp check Figure Junction Box Preamplifier Check Troubleshooting Guide No Power Coated glass electrode Clean with soft cloth and clean water Password protected Replacement Parts Part Number Description Section Return of Material Warranty RepairNON-WARRANTY Repair General Appendix a ORP Configuration Quick Startup ORP Table A-1. ORP Settings List Item Choices ORP Settings User Settings Choices ORP Settings User Settings Diagnostics Section Output setpoints Simulated tests Standardize 400 mV ORP Calibration Return of Materials Request Sensor or Circuit Board only Warranty Return of Material Specifications subject to change without notice