Outline of Menu Levels | Emerson 54e pH/ORP instruction

MODEL 54e pH/ORP	SECTION 5.0
	SOFTWARE CONFIGURATION

Accessing Calibrate, Program and Configure Menus. Operating configuration changes are made at the levels shown in Figure 5-1. Pressing any key from the main dis- play will access the main menu (top left). Refer to Appendix A for ORP measurements.

Level 1 Calibrate. To access calibration selections from the main menu, with the cursor on "Calibrate" press Enter (F4). All buffer calibration, pH standardization and tem- perature adjustments are made at this level (refer to Section 4.0 for these procedures).

Level 2 Program. To access the program level from the main menu, place the cursor over "Program" with the down arrow key. Then press Enter (F4). From the program level menu, changes can be made to the alarm setpoints and the output setpoints.

Level 3 Configure. To access the configure level from the main menu place cursor over "Program" and Enter (F4), then place cursor over "Configure" and Enter (F4). This level contains advanced selections, such as alarms, diag- nostics, autocal and others.

Blank

Out 2

R1

GI

In

AL2

AL3

FIGURE 5-1. Outline of Menu Levels

25

Image 31

Emerson 54e pH/ORP instruction manual Outline of Menu Levels

Contents

Model 54e pH/ORP PH/ORP Hart Analyzer/Controller Electrical Shock Hazard Essential InstructionsPage Model 54E PH/ORP Microprocessor Analyzer Description and SpecificationsSection Title List of Tables Appendix TitleTable No Title About This Document Table of Contents List of Figures General Description Section Description and SpecificationsDescription of Controls Current Outputs Specifications Physical Specifications GeneralPower Relative Humidity 95%, non condensing Alarms Recommended Sensors Analyzer Specifications @ 25C Code Options Ordering InformationPart NO. Description Unpacking and Inspection Section InstallationMechanical Installation Locating the Controller Panel Mounting Alarm Relay Output Wiring Section WiringPower Input Wiring Analog Output Wiring 454EPH02 PH Sensor Compatibility PH Sensor WiringTions will Result in Controller MALFUNC- Tion 454EPH01 Cable Dressing Final Electrical Check Wiring to Model Introduction Section Calibration Adjust temp 25.1 C Hold Mode OffTemperature Calibration Buffer 1 -- Wait Autocal bufferAutomatic TWO-POINT Calibration Use the arrow keys to select the correct buffer Auto buffer cal doneCalibration Notes Manual TWO-POINT Calibration Calibrate pointPt 04.00pH 25C Pt calibration done SINGLE-POINT pH Calibration Standardize 7.01 pH 59.16 mV/pH Temperature Compensation OptionsTemp comp Auto Output trim Output trim Hold ModeTrim Outputs PH Settings List Section Software Configuration Ranges Factory Settings User Settings Diagnostics Section Outline of Menu Levels Setpoint 07.00 pH Alarm High 14.00pHChanging Alarm Setpoints Simulate tests Changing Output Setpoints PID only Setpoint 7.00 pH4mA 0.00 pH 20mA 2.00 pH Setpoint + 06.90 pH MA +00.00 pH OutputOutput MA 0.00 pH 20 mA 14.00 pH Output 1 12.00 mA Simulated tests Alarm setpoints Output setpointsTest output Test alarm Testing Outputs and Alarms Test alarm 1 Open Test alarm 1 Open Measure pH Display right AL2 Security Caution Display contrast Timeout On Output Control Parameters Control ModeDisplay Changing Output Parameters Range 4-20 mAl Fault 22.00 mARange 4-20 mA Hold Disable feature Fault 22.00mAOutput 2 control Output 2 setup Hold feature setup Alarm 3 control AlarmsInterval timer Relay Default None Alarm LowSetpoint 0.01 pH Delay 0 sec Hysteresis 0.01 pH Delay 0 sec URV 2.00 pH Relay default NoneSetpoint +07.00 pH Time period 30 sec Alarm 4 Setup Alarm FaultFeed limit Disable Timeout 3600 sec Recovery 600 sec Timer DisableOn time 120 sec Interval Timer Examples Diagnostics Off DiagnosticsZero offset 60 mV Stabilize pH 0.01 pH Stabilize time 10 sec DiagnosticsAuto Calibration Setup Autocal Standard Standard Buffers Auto Calibration Setup Section Theory of Operation Continuous Sensor Diagnostics Typical set points Interval TimerSee .8 for instructions on chang- ing these setpoints Time Proportional Control TPC Mode Code Alarm Relays Analog Outputs Normal Mode Action Definitions Controller Mode PriorityController Mode Priority Chart Condition Definitions Measurement and Set Point Feedback Control PID Control Mode CombinationsPID Control Code PID Control Proportional Gain Plus Integral Reset Proportional Mode GainControl Loop Adjustment and Tuning Process Reaction Curve Process Reaction Curve Method PID Control Password Protection Section Special Procedures and FeaturesLevel 1 3 Password Privileges Lock all Configuring SecuritySecurity Custom Curve Temp coeff +.000 Solution Temperature CompensationSensor iso 07.00 pH Operate iso +07.00 pH Troubleshooting is easy as 1, 2, 3… Section Troubleshooting Diagnostic Messages Description of problem Diagnostic Messages Symptom Action Quick Troubleshooting Guide Diagnostic Variables Theoretical pH vs. Millivolt Values at 25C 77F Ohms Ambient Temperature Troubleshooting GuidelinesTemperature Compensation Circuit Troubleshooting Procedure Preamp in a junction box Figure Preamplifier Troubleshooting ProcedureController preamp check Figure Junction Box Preamplifier Check No Power Troubleshooting Guide Coated glass electrode Clean with soft cloth and clean water Password protected Part Number Description Replacement Parts General Warranty RepairNON-WARRANTY Repair Section Return of Material Quick Startup ORP Appendix a ORP Configuration Item Choices ORP Settings User Settings Table A-1. ORP Settings List Diagnostics Section Choices ORP Settings User Settings Simulated tests Output setpoints ORP Calibration Standardize 400 mV Sensor or Circuit Board only Return of Materials Request Return of Material Warranty Specifications subject to change without notice