Emerson 54e pH/ORP instruction manual Section Software Configuration, PH Settings List

MODEL 54e pH/ORP	SECTION 5.0
	SOFTWARE CONFIGURATION

SECTION 5.0

SOFTWARE CONFIGURATION

This section contains the following:

•An introduction to using the configuration process

•A List of Settings for the controller

•Step-by-step instructions and explanations for each parameter on the List

INTRODUCTION TO CONFIGURATION

The controller arrives from the factory configured and ready to operate as a pH controller. Refer to Appendix A for ORP meas- urements.

Figure 5-1 is an outline of the menu structure. Before attempting any changes refer to the parameter setup list shown in Table 5-1. This table presents a brief description and the possible options.

The factory setting is listed with a space for the user setting. It is recommended that the list be carefully reviewed before any changes are made.

On initial configuration, it is recommended that the parameters be entered in the order shown on the worksheet. This will reduce the chance of accidentally omitting a needed parameter.

TABLE 5-1. pH Settings List

ITEM		CHOICES	FACTORY SETTINGS		USER SETTINGS
PROGRAM LEVEL (Sections 5.1 - 5.3)
A. Alarm Setpoints (Section 5.2)
1. Alarm 1 (low action)		0 - 14 pH		0.00 pH	_______
2. Alarm 2 (high action)		0 - 14 pH		14.00 pH	_______
3. Alarm 3 (high action)		0 - 14 pH		14.00 pH	_______
B. Output Setpoints (Section 5.1, 5.3)
1.	Output 1: 4 mA	0 - 14 pH		0.00 pH	_______
2.	Output 1: 20 mA	0 - 14 pH		14.00 pH	_______
3.	Output 2: 4 mA	–15 - 130°C		0.0°C	_______
4.	Output 2: 20 mA	–15 - 130°C		100.0°C	_______
CONFIGURE LEVEL (Sections 5.5-5.9)
A. Display (Section 5.5)
1.	Measurement type	pH/ORP/Redox		pH	_______
2. pH Resolution		0.01 pH/0.1 pH		0.01 pH
3. Temperature Units		°C/°F		°C	_______
4.	Output 1 Units	mA/% (of full scale)		mA	_______
5.	Output 2 Units	mA/% (of full scale)		mA	_______
6.	Language	English/Français/Español/Deutsch/Italiano		English	_______
7.	Main display lower left	See Section 5.5		Alarm 1 Setpoint	_______
8.	Main display lower right	See Section 5.5		Alarm 2 Setpoint	_______
9.	Display contrast	0-9 (9 darkest)		5	_______
10. Test Timeout		On/Off		On	_______
11. Timeout Value		1-60 min		10 min	_______
B. Outputs (Section 5.6)
1.	Output 1 Control
	(a) Output 1 Measurement	Process/Temp/Glass Imp/Ref Imp		Process (pH)	_______
	(b) Output1 Control Mode	Normal/PID		Normal	_______
2a. Output 1 Setup (Normal)
	(a) Current Range	4-20 mA/0-20 mA		4-20 mA	_______
	(b) Dampening	0-299 Sec		0 Sec	_______
	(c) Hold Mode	Last value/Fixed value		Last value	_______
	(d) Fixed Hold Value (if (c) Fixed)	0-22 mA		21 mA	_______
	(e) Fault value	0-22 mA		22 mA	_______

22Continued on the following page