Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks VH-2402S manual Remote Management via the Console Port, In-Band Connections

Models: VH-2402S

1 110

Download 110 pages 48.8 Kb

Page 10

When attaching to a PC, set terminal emulation type to VT100, specify the port used by your PC (i.e., COM 1~4), and then set communications to 8 data bits, 1 stop bit, no parity, and 19200 bps (for initial configuration).

Also be sure to set flow control to “none.” (Refer to “Configuring the Serial Port” on page 19 for a complete description of configuration options.)

Remote Management via the Console Port

Configure the Switch Site

Connect the Management Module’s DB9 serial port to the modem’s serial port using standard cabling. For most modems which use a 25-pin port, you will have to provide an RS232 cable with a 9-pin connector on one end and a 25-pin connector on the other end. Set the modem at the switch’s site to force auto-answer mode. The following is a sample initialization string: “ATQ1S0=1&D0&K0&W” as defined below:

Q1 : Inhibit result codes to DTE

S0=1 : Auto answer on first ring

D0 : Don’t care DTR

K0 : Disables DTE/DCE flow control

W: Write command to modem memory

Configure the Remote Site

At the remote site, connect the PC’s COM port (COM 1~4) to the modem’s serial port. Set terminal emulation type to VT100, specify the port used by your PC (i.e., COM 1~4), and then set communications to 8 data bits, 1 stop bit, no parity, 19200 bps and no flow control.

In-Band Connections

Prior to accessing the Management Module via a network connection, you must first configure it with a valid IP address, subnet mask, and default gateway using an out-of-band connection or the BootP protocol.

Telnet Connection

Prior to accessing the Management Module via an in-band Telnet connection, you must first configure it with a valid IP address, subnet mask, and default gateway using an out-of-band connection or BootP protocol. After configuring the switch’s IP parameters, you can access the on-board configuration program from anywhere within the attached network.

Use the Network Configuration menu to specify the maximum number of simultaneous Telnet sessions that are supported by the system.

2 Management Overview

VH-2402S

Image 10

Enterasys Networks VH-2402S manual Remote Management via the Console Port, In-Band Connections, Configure the Switch Site

Contents

Fast Ethernet Switch Management GuidePage 9033645-01 9033645-01 Table of Contents Snmp Management Appendix A. Spanning Tree ConceptsIndex Vi Table of Contents VH-2402S Required Connections Configuration OptionsManagement Overview Console Port Out-of-Band ConnectionsRemote Management via the Console Port Configure the Switch SiteConfigure the Remote Site In-Band ConnectionsIn-Band Network Connection Management Overview VH-2402S VH-2402S User Interface OverviewUser Access Factory Defaults Factory Default SettingsGvrp Main Menu Selection DescriptionDisplays/configures extended bridge capabilities provided by System Information Menu System Information MenuDisplaying System Information System InformationDisplaying Switch Version and Module Information Switch InformationManagement Setup Menu Management Setup MenuChanging the Network Configuration Network ConfigurationIP Configuration IP ConfigurationIP Connectivity Test Ping IP Connectivity TestHttp Configuration 10. Http ConfigurationConfiguring the Serial Port 11. Serial Port Configuration12. Snmp Configuration Assigning Snmp ParametersConfiguring Community Names 13. Snmp CommunitiesConfiguring IP Trap Managers 14. IP Trap ManagersConsole Login Configuration 15. Console Login ConfigurationUsing Tftp Protocol to Download Over the Network Downloading System SoftwareSaving the System Configuration Parameter DescriptionConfiguring Management Access 18. Management ConfigurationConfiguring the Switch 19. Device Control MenuNot implemented in the current firmware release Configuring Port Parameters 20. Port ConfigurationViewing the Current Port Configuration 21. Port InformationUsing the Spanning Tree Algorithm 22. Spanning Tree Configuration Configuring Bridge STADevice with the lowest MAC address will then Configuring STA for Ports or Modules 24. Spanning Tree Port ConfigurationViewing the Current Spanning Tree Configuration 25. Spanning Tree InformationDisplaying the Current Bridge STA 26. Bridge STA InformationDisplaying the Current STA for Ports or Modules 27. Spanning Tree Port InformationRules defining port status are Using a Mirror Port for Analysis 28. Mirror Port ConfigurationConfiguring Port Trunks 29. Port Trunking Configuration Igmp Multicast Filtering Configuring Igmp 30. Igmp ConfigurationConfiguring Broadcast Storm Control 31. Broadcast Storm Control ConfigurationConfiguring Bridge MIB Extensions 32. Extended Bridge ConfigurationBy setting this parameter to False Configuring Traffic Classes 33 .1P ConfigurationPort Priority Configuration 34 .1P Port Priority Configuration802.1P Port Traffic Class Information 35 .1P Port Traffic Class InformationConfiguring Virtual LANs 802.1Q Vlan Base Information802.1Q Vlan Current Table Information 37 .1Q Vlan Current Table Information802.1Q Vlan Static Table Configuration 38 .1Q Vlan Static Table Configuration39 .1Q Vlan Static Table Configuration Example Port Assignment Vlan Configuration 40. Port Assignment Vlan ConfigurationMulticast Router Port Information 41. Multicast Router Port InformationStatic Multicast Router Port Configuration 42. Static Multicast Router Port ConfigurationIgmp Member Port Configuration 43. Igmp Member Port ConfigurationPort Security Configuration 44. Port Security ConfigurationMonitoring the Switch 45. Network Monitor MenuDisplaying Port Statistics 46. Port StatisticsDisplaying Rmon Statistics 47. Rmon StatisticsDrop Events Displaying the Unicast Address Table 48. Unicast Address TableDisplaying the IP Multicast Registration Table 49. IP Multicast Registration TableConfiguring Static Unicast Addresses 50. Static Unicast Addreeess Table ConfigurationResetting the System Logging Off the System66 VH-2402S User Interface Configuring & Monitoring the Switch Common TasksSetting Password Protection Connecting via Telnet Checking Network Configuration StatusAssigning an IP Address Setting Snmp Management Access Viewing Switch StatisticsConfiguring Port Mirroring Downloading a Software UpgradeDownloading Via the Serial Port Downloading Via Tftp9033645-01 Configuring Spanning Tree Parameters Configuring VLANs Configuring Class of ServiceConfiguring Port Operation Configuring the Unicast Address Table Setting a Default Gateway Configuring BootPConfiguring Port Trunks Configuring & Monitoring the Switch VH-2402S Snmp Management Snmp ProtocolMIB Objects RFC 1643 Ethernet-Like MIB RFC 1213 MIB-IIRFC 1573 Interfaces Evolution MIB RFC 1493 Bridge MIBIeee 802.1Q Q-MIB Compiling MIB Extensions Enterasys WebsiteEnterasys Proprietary MIB Extensions Appendix A. Spanning Tree Concepts Spanning Tree FeaturesGeneral Figure A-1. Spanning Tree Using VH-2402S Switches Spanning Tree Protocol in a NetworkTable A-1. Spanning Tree Protocol Defaults Spanning Tree Protocol ParametersSpanning Tree Protocol Operation 9033645-01 Spanning Tree Concepts VH-2402S Appendix B. Virtual Lans Vlans VLANs and Frame TaggingVlan Classification VH-2402S Vlan ConfigurationAssigning Ports to VLANs Port OverlappingForwarding Tagged/Untagged Frames Automatic Vlan RegistrationForwarding Traffic with Unknown Vlan Tags Appendix C. Class of Service Incoming tagged frames contain a priority level rangeFigure C-1. Class of Service Example Appendix D. IP Multicast Filtering Igmp Snooping and IP Multicast FilteringPage Index Tftp Page 150524-103 R02