Installlation | Extron electronic IPI 100, IPI 200 instruction

Installlation

IPI Rear Panel Features and Cabling

IPI 104 AAP, IPI 101 AAP

Rear Panel

C NO

POWER RELAY AUDIO OUT

Power 3

LAN

Contact

Relay 4

Audio Out 5

1a Intercom Port

2 AAP Mounting Screws (4)

1b LAN Port

2 AAP Mounting Screws (4)

IPI 204 AAP, IPI 201 AAP

Rear Panel

ÄIntercom port (IPI 101 AAP and IPI 104 AAP only) — This port is used for power, control, and voice data communication with the MLC. Plug one end of a standard, straight through, CAT 5, CAT 5e, or CAT 6 cable terminated with RJ‑45 connectors into this port. Plug the other end of the cable into the Intercom connector on the

MLC 226 IP’s rear panel, as shown in the following figure.

<100’ (30.4 m)

R	INTERCOM
	AUDIO OUT

HOST

CONTROL

1=DIGITAL I/O

2=Tx 3=Rx 5=GND

38400, N, 8, 1

LAN	PRESS TAB WITH
	TWEEKER TO REMOVE

IPI 101 AAP or IPI 104 AAP	MLC 226 IP Rear Panel
Rear Panel

CThis is not an Ethernet LAN connection. Do not connect these ports to the Ethernet.

NA 12 inch (30.5 cm) CAT 6 cable is included with each IPI. If you choose to terminate your own cable, the cable must be no longer than 100 feet (30.4 m). Cables must be terminated to the T586A or T586B standard and both ends of a cable must be wired to the same standard (see cable wiring on the next page).

2-2 IPI 100 and IPI 200 Series • Installation

Image 16

Extron electronic IPI 100, IPI 200 manual Installlation, MLC 226 IP’s rear panel, as shown in the following figure

Contents

MediaLink IP Intercom Interfaces Push to Talk Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch FCC Class a Notice Page Table of Contents Table of Contents, cont’d IPI 100 and IPI 200 Series Table of Contents Iii Iv IPI 100 and IPI 200 Series Table of Contents One Before you get Started Terms and symbols used in this manual PrefaceAbout this Manual IPI 101 AAP IPI 104 AAP IPI 201 Series IPI 204 Series About the IP Intercom Modules Additional reference material Security features FeaturesLED indicator to show when the room is being monitored System Requirements UL Requirements Preface, cont’d Installlation Two IPI 100 and IPI 200 Series Installation InstalllationMLC 226 IP’s rear panel, as shown in the following figure Connector MLC 226 IP AAP or a mounting frame Installlation, cont’d MLC Audio Connection Sample Applications Single PC to panel Multiple PCs to panel Network Panel-to-panel mode Server mode Intercom with amplifier MPA Installlation, cont’d Three Operation Operation Front Panel Features and OperationIPI 100 and IPI 200 Series Operation Button Operation Push to talk operationIndication lighting\⤀ Button Color Indication Operation Initial Configuration Four IPI 100 and IPI 200 Series Initial Configuration Initial ConfigurationBefore you Begin Setting the IP address using Global Configurator At its factory default IP addressIPI 200 Series intercom unit must be Advanced button name changes to Basic Open a Web browser on the local PC Setting the IP address using embedded Web pagesIntercom unit’s embedded Web page is displayed Return to the TCP/IP Properties dialog box on the PC Setting the IP address using the ARP command Arp s IP address MAC address Five HelpDesk Software Installling the Software HelpDesk SoftwareIntroduction to the Software IPI 100 and IPI 200 Series HelpDesk Software Log-in as User Log-in as a HelpDesk Administrator Starting the Program HelpDesk Software, cont’d Configuring the IP Intercom System Basic ConfigurationUsing the Configuration Utility Use the drop-down menu to select the appropriate option Importing a GC2/GCZ file Click Import. a Windows Open dialog box opensEntering an IP address manuallly Select Manually by IP Address from the drop-down menu Scanning the local subnet Configuring an IP device with the configuration utility Talk mode Listen mode Start speaking. While Group announcement Select an available group or All Intercoms Changing the default .wav file for intercom events Loading a pre-recorded .wav fileTo load a pre-recorded file Setting up a peer-to-peer network Calll forwarding Setting up one PC as a server None of the PCs can be set to Server ModeAll HelpDesks must be linked to the Server PC Server PC must be set to Server Mode HelpDesk Software, cont’d Specifications, Part Numbers Accessories Specifications, Part Numbers, Accessories Specifications IPI 100 Series Accessories IPI 100 Series\⤀ Accessories Part numberIncluded Parts IPI 100 Series\⤀ Included parts Replacement Part number Specifications, Part Numbers, Accessories, cont’d Specifications IPI 200 Series Extron Lbs 0.2 kg Included Parts IPI 200 Series\⤀ Accessories IPI 200 Series\⤀Amplifiers, cable, miscelllany Part number Specifications, Part Numbers, Accessories, cont’d AppendixBB SIS Programming and Control SIS Programming and Control Host-to-IPI CommunicationsIPI-initiated Messages IPI 100 and IPI 200 Series SIS Programming and Control Error responses Password informationError response references Commands and Reponses Using the command/response table Symbol definitions = On/off status 0 = off / disable 1 = on /enableTelnet Web Browser = Escape key hex 1B Use W instead of Esc for Web browsers X4! = X4 = = on, disable/lock the front panel X7! = X20 Command/response table for SIS commands+X20 Command Ascii Telnet\⤀ URL Encoded Response X1! CX1! X1! X1! X1! X1@ CN Ipn X1@ IpnX4 X1@ or X4 X3$ X1$ CIX1$ X1* X2@ X6$,X1$ EB Bmd X6$,X1$ X6$ EB X3# CU IpuX4! CK X5@ or Pvl X5@ Directory commands Stream Files via Telnet or RS-232 Stream Files via Port File handling commandsIPI 100 and IPI 200 Series SIS Programming and Control B-15 1AE 0AE Reset zap\⤀/Erase Commands IPI 100 and IPI 200 Series SIS Programming and Control B-17 SIS Programming and Control, cont’d AppendixCC Mounting Mounting the IPI 100 Series MountingIPI 100 and IPI 200 Series Mounting Mounting the IPI 200 Series Mounting, cont’d Button Labels IPI 100 and IPI 200 SeriesDAppendix D Installling or Replacing Button Labels Installling the Button-Label Generator softwareButton Labels Button Label Generator software Using the Button-Label Generator software Installling Button Labels Text Extron Warranty Quick Installation Checklist