Open a Web browser on the local PC | Extron electronic IPI 100

Initial Configuration, cont’d

Setting the IP address using embedded Web pages

Each IPI 200 Series intercom unit contains an on-board Web server with interactive pages that can be used to configure the device.

The intercom unit must be at its factory default IP address.

To set an IP address via embedded Web pages:

1.	Connect an Ethernet crossover cable between the device and a local PC.
2.	On the PC, locate the TCP/IP Properties dialog box.
	On Windows XP, the TCP/IP Properties dialog box is found at:
	Start > My Network Places > right-click to Properties > Local Area
	Connection > right-click to Properties > Internet Protocol (TCP/IP) >
	Properties.
3.	Record the current IP address, subnet mask, default gateway and DHCP
	settings. You will need this information later to return the PC to its original
	TCP/IP settings.
	IP Address:
	.	.	.

Subnet Mask:

. . .

4. Enter the following:

IP address: 192.168.254.253

Subnet mask: 255.255.0.0

Default gateway: <blank>

5. Click OK.

6.	Open a Web browser on the local PC.
7.	Enter 192.168.254.254 in the browser’s Address field and press the Enter key.
	The intercom unit’s embedded Web page is displayed.
8.	Click the Configuration tab.

4-4 IPI 100 and IPI 200 Series • Initial Configuration

Image 32

Extron electronic IPI 100, IPI 200 Setting the IP address using embedded Web pages, Open a Web browser on the local PC

Contents

MediaLink IP Intercom Interfaces Push to Talk Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen Deutsch FCC Class a Notice Page Table of Contents Table of Contents, cont’d IPI 100 and IPI 200 Series Table of Contents Iii Iv IPI 100 and IPI 200 Series Table of Contents One Before you get Started Terms and symbols used in this manual PrefaceAbout this Manual IPI 101 AAP IPI 104 AAP IPI 201 Series IPI 204 Series About the IP Intercom Modules Additional reference material LED indicator to show when the room is being monitored FeaturesSecurity features System Requirements UL Requirements Preface, cont’d Installlation Two MLC 226 IP’s rear panel, as shown in the following figure InstalllationIPI 100 and IPI 200 Series Installation Connector MLC 226 IP AAP or a mounting frame Installlation, cont’d MLC Audio Connection Sample Applications Single PC to panel Multiple PCs to panel Network Panel-to-panel mode Server mode Intercom with amplifier MPA Installlation, cont’d Three Operation IPI 100 and IPI 200 Series Operation Front Panel Features and OperationOperation Button Operation Push to talk operationIndication lighting\⤀ Button Color Indication Operation Initial Configuration Four Before you Begin Initial ConfigurationIPI 100 and IPI 200 Series Initial Configuration Setting the IP address using Global Configurator At its factory default IP addressIPI 200 Series intercom unit must be Advanced button name changes to Basic Intercom unit’s embedded Web page is displayed Setting the IP address using embedded Web pagesOpen a Web browser on the local PC Return to the TCP/IP Properties dialog box on the PC Setting the IP address using the ARP command Arp s IP address MAC address Five HelpDesk Software Installling the Software HelpDesk SoftwareIntroduction to the Software IPI 100 and IPI 200 Series HelpDesk Software Log-in as User Log-in as a HelpDesk Administrator Starting the Program HelpDesk Software, cont’d Configuring the IP Intercom System Basic ConfigurationUsing the Configuration Utility Use the drop-down menu to select the appropriate option Importing a GC2/GCZ file Click Import. a Windows Open dialog box opensEntering an IP address manuallly Select Manually by IP Address from the drop-down menu Scanning the local subnet Configuring an IP device with the configuration utility Talk mode Listen mode Start speaking. While Group announcement Select an available group or All Intercoms To load a pre-recorded file Loading a pre-recorded .wav fileChanging the default .wav file for intercom events Setting up a peer-to-peer network Calll forwarding All HelpDesks must be linked to the Server PC None of the PCs can be set to Server ModeSetting up one PC as a server Server PC must be set to Server Mode HelpDesk Software, cont’d Specifications, Part Numbers Accessories Specifications, Part Numbers, Accessories Specifications IPI 100 Series Accessories IPI 100 Series\⤀ Accessories Part numberIncluded Parts IPI 100 Series\⤀ Included parts Replacement Part number Specifications, Part Numbers, Accessories, cont’d Specifications IPI 200 Series Extron Lbs 0.2 kg Amplifiers, cable, miscelllany Part number Accessories IPI 200 Series\⤀Included Parts IPI 200 Series\⤀ Specifications, Part Numbers, Accessories, cont’d AppendixBB SIS Programming and Control SIS Programming and Control Host-to-IPI CommunicationsIPI-initiated Messages IPI 100 and IPI 200 Series SIS Programming and Control Error response references Password informationError responses Commands and Reponses Using the command/response table Symbol definitions = On/off status 0 = off / disable 1 = on /enableTelnet Web Browser = Escape key hex 1B Use W instead of Esc for Web browsers X4! = X4 = = on, disable/lock the front panel X7! = +X20 Command/response table for SIS commandsX20 Command Ascii Telnet\⤀ URL Encoded Response X1! CX1! X1! X1! X1! X1@ CN Ipn X1@ IpnX4 X1@ or X4 X3$ X1$ CIX1$ X1* X2@ X6$,X1$ EB Bmd X6$,X1$ X6$ EB X3# CU IpuX4! CK X5@ or Pvl X5@ Directory commands Stream Files via Telnet or RS-232 IPI 100 and IPI 200 Series SIS Programming and Control B-15 File handling commandsStream Files via Port 1AE 0AE Reset zap\⤀/Erase Commands IPI 100 and IPI 200 Series SIS Programming and Control B-17 SIS Programming and Control, cont’d AppendixCC Mounting IPI 100 and IPI 200 Series Mounting MountingMounting the IPI 100 Series Mounting the IPI 200 Series Mounting, cont’d Button Labels IPI 100 and IPI 200 SeriesDAppendix D Installling or Replacing Button Labels Installling the Button-Label Generator softwareButton Labels Button Label Generator software Using the Button-Label Generator software Installling Button Labels Text Extron Warranty Quick Installation Checklist