X7! = | Extron electronic IPI 200, IPI 100 manual

X6$ = Broadcast repetition interval in seconds (0 to 255 [4.25 minutes], default = 0 = off).

X7! =

X7@ =

Hardware (MAC) address: 4 most-significant hex nibbles converted into single 16-bit decimal number.

Hardware (MAC) address: 8 least significant hex nibbles converted into single 32-bit decimal number.

NThis could be as large as 10 digits.

X20^ = Voltage (in volts)

X20& =Temperature in degrees Celsius (the response is 3 digits including leading zeros)

X20( = Front panel lockout (executive mode) status 0 = off/unlocked (default)

1 = on, disable/lock the front panel

IPI 100 and IPI 200 Series • SIS Programming and Control

B-7

Image 65

Extron electronic IPI 200, IPI 100 manual X7! =, = on, disable/lock the front panel

Contents

Push to Talk MediaLink IP Intercom Interfaces Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen Deutsch FCC Class a Notice Page Table of Contents Table of Contents, cont’d IPI 100 and IPI 200 Series Table of Contents Iii Iv IPI 100 and IPI 200 Series Table of Contents Before you get Started One Preface Terms and symbols used in this manualAbout this Manual IPI 101 AAP IPI 104 AAP IPI 201 Series IPI 204 Series Additional reference material About the IP Intercom Modules LED indicator to show when the room is being monitored FeaturesSecurity features UL Requirements System Requirements Preface, cont’d Two Installlation MLC 226 IP’s rear panel, as shown in the following figure InstalllationIPI 100 and IPI 200 Series Installation MLC 226 IP AAP or a mounting frame Connector MLC Audio Connection Installlation, cont’d Single PC to panel Sample Applications Network Multiple PCs to panel Panel-to-panel mode Server mode MPA Intercom with amplifier Installlation, cont’d Operation Three IPI 100 and IPI 200 Series Operation Front Panel Features and OperationOperation Push to talk operation Button OperationIndication lighting\⤀ Button Color Indication Operation Four Initial Configuration Before you Begin Initial ConfigurationIPI 100 and IPI 200 Series Initial Configuration At its factory default IP address Setting the IP address using Global ConfiguratorIPI 200 Series intercom unit must be Advanced button name changes to Basic Intercom unit’s embedded Web page is displayed Setting the IP address using embedded Web pagesOpen a Web browser on the local PC Return to the TCP/IP Properties dialog box on the PC Arp s IP address MAC address Setting the IP address using the ARP command HelpDesk Software Five HelpDesk Software Installling the SoftwareIntroduction to the Software IPI 100 and IPI 200 Series HelpDesk Software Starting the Program Log-in as User Log-in as a HelpDesk Administrator HelpDesk Software, cont’d Basic Configuration Configuring the IP Intercom SystemUsing the Configuration Utility Use the drop-down menu to select the appropriate option Click Import. a Windows Open dialog box opens Importing a GC2/GCZ fileEntering an IP address manuallly Select Manually by IP Address from the drop-down menu Scanning the local subnet Configuring an IP device with the configuration utility Talk mode Start speaking. While Listen mode Select an available group or All Intercoms Group announcement To load a pre-recorded file Loading a pre-recorded .wav fileChanging the default .wav file for intercom events Calll forwarding Setting up a peer-to-peer network All HelpDesks must be linked to the Server PC None of the PCs can be set to Server ModeSetting up one PC as a server Server PC must be set to Server Mode HelpDesk Software, cont’d Specifications, Part Numbers Accessories Specifications IPI 100 Series Specifications, Part Numbers, Accessories Accessories Part number Accessories IPI 100 Series\⤀Included Parts IPI 100 Series\⤀ Included parts Replacement Part number Specifications IPI 200 Series Specifications, Part Numbers, Accessories, cont’d Extron Lbs 0.2 kg Amplifiers, cable, miscelllany Part number Accessories IPI 200 Series\⤀Included Parts IPI 200 Series\⤀ Specifications, Part Numbers, Accessories, cont’d SIS Programming and Control AppendixBB Host-to-IPI Communications SIS Programming and ControlIPI-initiated Messages IPI 100 and IPI 200 Series SIS Programming and Control Error response references Password informationError responses Using the command/response table Commands and Reponses = On/off status 0 = off / disable 1 = on /enable Symbol definitionsTelnet Web Browser = Escape key hex 1B Use W instead of Esc for Web browsers X4! = X4 = X7! = = on, disable/lock the front panel +X20 Command/response table for SIS commandsX20 X1! C Command Ascii Telnet\⤀ URL Encoded ResponseX1! X1! X1! X1! IpnX4 X1@ CN Ipn X1@ X1@ or X4 X1$ CI X3$ X1$ X1* X6$,X1$ EB X2@ Bmd X6$,X1$ X6$ EB CK X3# CU IpuX4! X5@ or Pvl X5@ Stream Files via Telnet or RS-232 Directory commands IPI 100 and IPI 200 Series SIS Programming and Control B-15 File handling commandsStream Files via Port 0AE 1AE IPI 100 and IPI 200 Series SIS Programming and Control B-17 Reset zap\⤀/Erase Commands SIS Programming and Control, cont’d Mounting AppendixCC IPI 100 and IPI 200 Series Mounting MountingMounting the IPI 100 Series Mounting the IPI 200 Series Mounting, cont’d IPI 100 and IPI 200 SeriesDAppendix D Button Labels Installling the Button-Label Generator software Installling or Replacing Button LabelsButton Labels Button Label Generator software Using the Button-Label Generator software Text Installling Button Labels Extron Warranty Quick Installation Checklist