Troubleshooting | Fluke 199, 196, 192 specs

Maintaining the Test Tool

Troubleshooting 8

Troubleshooting

The Test Tool Does Not Start Up

•The batteries may be completely empty. In this case the test tool will not start up, even if it is powered by the battery charger. Charge the batteries first: power the test tool with the battery charger without turning it on. Wait about 15 minutes and try turning on the test tool again.

The Test Tool Shuts Down After A Few Seconds

•The batteries may be empty. Check the battery symbol at the top right of the screen. Asymbol indicates that the batteries are empty and must be charged.

The Screen Remains Black

•Make sure that the test tool is on.

•You might have a problem with the screen contrast.

Press , then press . Now you can use the arrow keys to adjust the contrast.

The Operation Time Of Fully Charged Batteries Is Too Short

•The batteries may be in poor condition. Refresh the batteries to optimize the condition of the batteries again. It is advised to refresh the batteries about four times a year.

The Printer Does Not Print

•Make sure that the interface cable is properly connected between the test tool and the printer.

•Make sure that you have selected the correct printer type. (See Chapter 6.)

•Make sure that the baud rate matches with the printer. If not, select another baud rate.

(See Chapter 6.)

•If you are using the PAC91 (Print Adapter Cable), make sure that it is turned on.

85

Image 93

Fluke 199, 196, 192 user manual Troubleshooting

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using The Recorder Functions Using The MultimeterUsing Replay, Zoom and Cursors Fluke 192/196/199 Iii Index Specifications Manufacturer Declaration of ConformityStatement of Conformity Sample tests ScopeMeter Test Tool Kit Unpacking the Test Tool Kit # Description Description Safety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Screen After Reset Resetting the Test Tool Open the Waveform Options Navigating a Menu Input Connections Hiding Key Labels and Menus Scope Connections Making Scope Connections Screen After an Auto Set Displaying an Unknown Signal with Connect-and-View Making Automatic Scope Measurements Select the Peak-PeakMeasurement Hz and V peak-peak as Scope Readings Freezing the Screen Using Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Suppressing High Frequency Noise Displaying Glitches Acquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Mathematics... to open Analyzing WaveformsMathematics menu Or a vs B Making Meter Connections Using The Multimeter Measuring Resistance Values Making Multimeter Measurements Highlight a ac Making a Current MeasurementOpen the Current Probe Submenu Ampere Measurement Readings Selecting Auto/Manual Ranges Freezing the Readings Making a Relative Measurement Making Relative Measurements Opening the Recorder Main Menu Using The Recorder Functions Plotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope TrendPlot Reading Displaying Recorded Data Turning Off the TrendPlot Display Changing the Recorder OptionsOpen the Recorder Options Menu Recording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Triggered Single Sweep Recording Analyzing a TrendPlot or Scope Record Replaying the 100 Most Recent Scope Screens Using Replay, Zoom and Cursors Replaying a Waveform Replaying Step-by-Step Replaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in a Waveform Zooming in on a Waveform Turning Off the Zoom Function Displaying the Zoomed Waveform Making Cursor Measurements Using Horizontal Cursors on a Waveform Turn off the cursors Using Vertical Cursors on a Waveform Making Rise Time Measurements Using Cursors on a A+B, A-B or A*B Waveform Triggering on Waveforms Screen with all Trigger Information Setting Trigger Level and Slope Trigger Delay or Pre-trigger View Using Trigger Delay or Pre-trigger Automatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Open the Trigger Options menu Open the Trigger on Edge menu Triggering on EdgesSelect Free Run, jump to Noise Reject Filter Making a Single Acquisition Triggering on Noisy WaveformsSelect On Trigger, jump to Noise Set Noise reject Filter to On Making a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing Pulses Triggering on Missing Pulses Saving and Recalling Using Memory, PC and Printer Saving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Scroll through all stored screens Recalling a Setup Configuration Viewing Stored Screens Documenting Screens Connecting to a Computer Connecting a Serial Printer Connecting to a Printer Open the Printer Setup submenu Setting up the Printing ConfigurationPrinting a Screen Baud Rate Fluke 192/196/199 Tips Using the Standard Accessories Heavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test Probes Tips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Suppressing Key Labels and Menu’s Using the Tilt StandTurn the test tool off Press and hold Changing the Information Language Adjusting the Contrast and BrightnessOpen the Language Select Accept French as the language Changing Date and Time Open Date Adjust menuChoose 1999, jump to Month Choose 04, jump to Day Setting the Power Down Timer Saving Battery Life Changing the Auto Set Options Open the User Options menu Open the Auto Set Adjust MenuTo Coupling Select Unchanged Cleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Open the User Options menu Extending Battery Operation Time Calibrating the Voltage Probes Replacing the NiMH Battery Pack BP190Select 101, then return Select Voltage, then jump to Maintaining the Test Tool Standard Accessories Parts and AccessoriesDisplaying Calibration Information Open the Version & Calibration Ordering Code Standard Accessories TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not Function Performance Characteristics SpecificationsSafety Characteristics Introduction Dual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Automatic Connect-and-View Trigger Trigger and DelayEdge Trigger Isolated External Trigger Automatic Scope Measurements AC+DC Voltage True RMS AC Voltage VAC Peak Amperes AMPFrequency Hz Duty Cycle Duty Phase PowerTemperature Temp Decibel dB DMM Measurements on Meter Inputs Meter Diode With Optional Temperature Probe Recorder TrendPlot Meter or ScopeScope Record Miscellaneous Zoom, Replay and Cursors Memory Probe CalibrationOptical InterfacePort Mechanical Environmental Safety Max. Input VoltagesMax. Floating Voltage Electrical specifications SafetyProbe Environmental 102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity 104 Numerics Index 106 107 108