Automatic Trigger Options, Open the Automatic Trigger | Fluke 199

Fluke 192/196/199

Users Manual

Automatic Trigger Options

In the trigger menu, settings for automatic triggering can be changed as follows. (See also Chapter 1: “Displaying an Unknown Signal with Connect-and-View”)

1					Display the TRIGGER key labels.
1					Display the TRIGGER key labels.

If the frequency range of the automatic triggering is set to

>15 Hz, the Connect-and-View™ function responds more quickly. The response is quicker because the test tool is instructed not to analyze low frequency signal components. However, when you measure frequencies lower than 15 Hz, the test tool must be instructed to analyze low frequency components for automatic triggering:

Note

The TRIGGER key labels can differ depending on the latest trigger function used.

2 Open the Trigger Options menu.

4						Select > 1 HZ and return to the
						measurement screen.
						measurement screen.

3						Open the Automatic Trigger
						menu.
						menu.

46

Image 54

Fluke 199, 196, 192 user manual Automatic Trigger Options, Open the Trigger Options menu, Open the Automatic Trigger

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using Replay, Zoom and Cursors Using The MultimeterUsing The Recorder Functions Fluke 192/196/199 Iii Specifications Index Statement of Conformity Declaration of ConformityManufacturer Sample tests Unpacking the Test Tool Kit ScopeMeter Test Tool Kit Description # Description Safety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Resetting the Test Tool Screen After Reset Navigating a Menu Open the Waveform Options Hiding Key Labels and Menus Input Connections Making Scope Connections Scope Connections Displaying an Unknown Signal with Connect-and-View Screen After an Auto Set Making Automatic Scope Measurements Select the Peak-PeakMeasurement Freezing the Screen Hz and V peak-peak as Scope Readings Using Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Displaying Glitches Suppressing High Frequency Noise Acquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Mathematics menu Analyzing WaveformsMathematics... to open Or a vs B Using The Multimeter Making Meter Connections Making Multimeter Measurements Measuring Resistance Values Open the Current Probe Making a Current MeasurementHighlight a ac Submenu Ampere Measurement Readings Freezing the Readings Selecting Auto/Manual Ranges Making Relative Measurements Making a Relative Measurement Using The Recorder Functions Opening the Recorder Main Menu Plotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope Displaying Recorded Data TrendPlot Reading Open the Recorder Options Changing the Recorder OptionsTurning Off the TrendPlot Display Menu Recording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Analyzing a TrendPlot or Scope Record Triggered Single Sweep Recording Using Replay, Zoom and Cursors Replaying the 100 Most Recent Scope Screens Replaying Step-by-Step Replaying a Waveform Replaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in on a Waveform Zooming in a Waveform Displaying the Zoomed Waveform Turning Off the Zoom Function Using Horizontal Cursors on a Waveform Making Cursor Measurements Using Vertical Cursors on a Waveform Turn off the cursors Using Cursors on a A+B, A-B or A*B Waveform Making Rise Time Measurements Triggering on Waveforms Setting Trigger Level and Slope Screen with all Trigger Information Using Trigger Delay or Pre-trigger Trigger Delay or Pre-trigger View Automatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Select Free Run, jump to Noise Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Reject Filter Select On Trigger, jump to Noise Triggering on Noisy WaveformsMaking a Single Acquisition Set Noise reject Filter to On Making a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Finding Missing Pulses Open the Trigger Options menu Select On Trigger Triggering on Missing Pulses Using Memory, PC and Printer Saving and Recalling Saving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Recalling a Setup Configuration Viewing Stored Screens Scroll through all stored screens Connecting to a Computer Documenting Screens Connecting to a Printer Connecting a Serial Printer Printing a Screen Setting up the Printing ConfigurationOpen the Printer Setup submenu Baud Rate Fluke 192/196/199 Using the Standard Accessories Tips Probing Using 2-mm Heavy Duty Test Probes Heavy Duty Fixed Connections for Scope Tips Using the Standard Accessories Using the Independently Floating Isolated Inputs Measuring Using Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Turn the test tool off Using the Tilt StandSuppressing Key Labels and Menu’s Press and hold Open the Language Select Adjusting the Contrast and BrightnessChanging the Information Language Accept French as the language Choose 1999, jump to Month Open Date Adjust menuChanging Date and Time Choose 04, jump to Day Saving Battery Life Setting the Power Down Timer To Coupling Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options Select Unchanged Cleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Extending Battery Operation Time Open the User Options menu Select 101, then return Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select Voltage, then jump to Maintaining the Test Tool Displaying Calibration Information Parts and AccessoriesStandard Accessories Open the Version & Calibration Standard Accessories Ordering Code TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting Battery Operated Fluke Accessories Do Not Function FlukeView Does Not Recognize The Test Tool Safety Characteristics SpecificationsPerformance Characteristics Introduction Dual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Edge Trigger Trigger and DelayAutomatic Connect-and-View Trigger Isolated External Trigger Automatic Scope Measurements AC Voltage VAC AC+DC Voltage True RMS Frequency Hz Amperes AMPPeak Duty Cycle Duty Temperature Temp PowerPhase Decibel dB Meter DMM Measurements on Meter Inputs With Optional Temperature Probe Diode Recorder TrendPlot Meter or ScopeScope Record Zoom, Replay and Cursors Miscellaneous Optical InterfacePort Probe CalibrationMemory Mechanical Environmental Safety Max. Input VoltagesMax. Floating Voltage Probe SafetyElectrical specifications Environmental 102 Electromagnetic Immunity Disturbance less than 10% of full scale = 3V/m 104 Index Numerics 106 107 108