Using The Scope, About this Chapter | Fluke 199, 196, 192 manual

About this Chapter

This chapter provides a step-by-step introduction to the scope functions of the test tool. The introduction does not cover all of the capabilities of the scope functions but gives basic examples to show how to use the menus and perform basic operations.

Powering the Test Tool

Follow the procedure (steps 1 through 3) in Figure 2 to power the test tool from a standard ac outlet.

See Chapter 8 for instructions on using battery power.

Turn the test tool on with the on/off key.

The test tool powers up in its last setup configuration.

Chapter 1

Using The Scope

Figure 2. Powering the Test Tool

7

Image 15

Fluke 199, 196, 192 user manual Using The Scope, About this Chapter, Powering the Test Tool

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Fluke 192/196/199 Using The MultimeterUsing The Recorder Functions Using Replay, Zoom and Cursors Iii Index Specifications Sample tests Declaration of ConformityManufacturer Statement of Conformity ScopeMeter Test Tool Kit Unpacking the Test Tool Kit # Description Description Safety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Screen After Reset Resetting the Test Tool Open the Waveform Options Navigating a Menu Input Connections Hiding Key Labels and Menus Scope Connections Making Scope Connections Screen After an Auto Set Displaying an Unknown Signal with Connect-and-View Making Automatic Scope Measurements Select the Peak-PeakMeasurement Hz and V peak-peak as Scope Readings Freezing the Screen Using Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Suppressing High Frequency Noise Displaying Glitches Acquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Or a vs B Analyzing WaveformsMathematics... to open Mathematics menu Making Meter Connections Using The Multimeter Measuring Resistance Values Making Multimeter Measurements Submenu Making a Current MeasurementHighlight a ac Open the Current Probe Ampere Measurement Readings Selecting Auto/Manual Ranges Freezing the Readings Making a Relative Measurement Making Relative Measurements Opening the Recorder Main Menu Using The Recorder Functions Plotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope TrendPlot Reading Displaying Recorded Data Menu Changing the Recorder OptionsTurning Off the TrendPlot Display Open the Recorder Options Recording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Triggered Single Sweep Recording Analyzing a TrendPlot or Scope Record Replaying the 100 Most Recent Scope Screens Using Replay, Zoom and Cursors Replaying a Waveform Replaying Step-by-Step Replaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in a Waveform Zooming in on a Waveform Turning Off the Zoom Function Displaying the Zoomed Waveform Making Cursor Measurements Using Horizontal Cursors on a Waveform Turn off the cursors Using Vertical Cursors on a Waveform Making Rise Time Measurements Using Cursors on a A+B, A-B or A*B Waveform Triggering on Waveforms Screen with all Trigger Information Setting Trigger Level and Slope Trigger Delay or Pre-trigger View Using Trigger Delay or Pre-trigger Automatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Reject Filter Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Select Free Run, jump to Noise Set Noise reject Filter to On Triggering on Noisy WaveformsMaking a Single Acquisition Select On Trigger, jump to Noise Making a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing Pulses Triggering on Missing Pulses Saving and Recalling Using Memory, PC and Printer Saving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Scroll through all stored screens Recalling a Setup Configuration Viewing Stored Screens Documenting Screens Connecting to a Computer Connecting a Serial Printer Connecting to a Printer Baud Rate Setting up the Printing ConfigurationOpen the Printer Setup submenu Printing a Screen Fluke 192/196/199 Tips Using the Standard Accessories Heavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test Probes Tips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Press and hold Using the Tilt StandSuppressing Key Labels and Menu’s Turn the test tool off Accept French as the language Adjusting the Contrast and BrightnessChanging the Information Language Open the Language Select Choose 04, jump to Day Open Date Adjust menuChanging Date and Time Choose 1999, jump to Month Setting the Power Down Timer Saving Battery Life Select Unchanged Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options To Coupling Cleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Open the User Options menu Extending Battery Operation Time Select Voltage, then jump to Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select 101, then return Maintaining the Test Tool Open the Version & Calibration Parts and AccessoriesStandard Accessories Displaying Calibration Information Ordering Code Standard Accessories TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not Function Introduction SpecificationsPerformance Characteristics Safety Characteristics Dual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Isolated External Trigger Trigger and DelayAutomatic Connect-and-View Trigger Edge Trigger Automatic Scope Measurements AC+DC Voltage True RMS AC Voltage VAC Duty Cycle Duty Amperes AMPPeak Frequency Hz Decibel dB PowerPhase Temperature Temp DMM Measurements on Meter Inputs Meter Diode With Optional Temperature Probe Recorder TrendPlot Meter or ScopeScope Record Miscellaneous Zoom, Replay and Cursors Mechanical Probe CalibrationMemory Optical InterfacePort Environmental Safety Max. Input VoltagesMax. Floating Voltage Environmental SafetyElectrical specifications Probe 102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity 104 Numerics Index 106 107 108