Using Replay, Zoom and Cursors | Fluke 196, 199, 192 specs

Chapter 4

Using Replay, Zoom and Cursors

About this Chapter

This chapter covers the capabilities of the analysis functions Cursor, Zoom, and Replay. These functions can be used with one or more of the primary functions Scope, TrendPlot or Scope Record.

It is possible to combine two or three analysis functions. A typical application using these functions follows:

•First replay the last screens to find the screen of special interest.

•Then zoom in on the signal event.

•Finally, make measurements using the cursors.

Replaying the 100 Most Recent Scope Screens

When you are in scope mode, the test tool automatically stores the 100 most recent screens. When you press the HOLD key or the REPLAY key, the memory contents are frozen. Use the functions in the REPLAY menu to “go back in time” by stepping through the stored screens to find the screen of your interest. This feature lets you capture and view signals even if you did not press HOLD.

35

Image 43

Fluke 196, 199, 192 user manual Using Replay, Zoom and Cursors, Replaying the 100 Most Recent Scope Screens

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Fluke 192/196/199 Using The MultimeterUsing The Recorder Functions Using Replay, Zoom and Cursors Iii Index Specifications Sample tests Declaration of ConformityManufacturer Statement of Conformity ScopeMeter Test Tool Kit Unpacking the Test Tool Kit # Description Description Safety Information Read First Safety Information Read First Use of the test tool in a manner not specified may If Safety Features are ImpairedImpair the protection provided by the equipment Powering the Test Tool Using The ScopeAbout this Chapter Screen After Reset Resetting the Test Tool Open the Waveform Options Navigating a Menu Input Connections Hiding Key Labels and Menus Scope Connections Making Scope Connections Screen After an Auto Set Displaying an Unknown Signal with Connect-and-View Select the Peak-Peak Making Automatic Scope MeasurementsMeasurement Hz and V peak-peak as Scope Readings Freezing the Screen Using Average for Smoothing Waveforms Using Average, Persistence and Glitch CaptureJump to Waveform Jump to Waveform and Select Using Persistence to Display WaveformsPersistence , then select Infinite Suppressing High Frequency Noise Displaying Glitches Selecting AC-Coupling Acquiring WaveformsReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Or a vs B Analyzing WaveformsMathematics... to open Mathematics menu Making Meter Connections Using The Multimeter Measuring Resistance Values Making Multimeter Measurements Submenu Making a Current MeasurementHighlight a ac Open the Current Probe Ampere Measurement Readings Selecting Auto/Manual Ranges Freezing the Readings Making a Relative Measurement Making Relative Measurements Opening the Recorder Main Menu Using The Recorder Functions Starting a TrendPlot Function Plotting Measurements Over Time TrendPlotHighlight Trend Plot Scope TrendPlot Reading Displaying Recorded Data Menu Changing the Recorder OptionsTurning Off the TrendPlot Display Open the Recorder Options Starting a Scope Record Function Recording Scope Waveforms In Deep Memory Scope RecordHighlight Scope Record Using ScopeRecord in Single Sweep Mode Jump to Display Glitches Select Yes, then jump to Mode Using Scope Record in Triggered Single Sweep ModeLevel Triggered Single Sweep Recording Analyzing a TrendPlot or Scope Record Replaying the 100 Most Recent Scope Screens Using Replay, Zoom and Cursors Replaying a Waveform Replaying Step-by-Step Turning Off the Replay Function Replaying ContinuouslyCapturing 100 Intermittents Automatically Zooming in a Waveform Zooming in on a Waveform Turning Off the Zoom Function Displaying the Zoomed Waveform Making Cursor Measurements Using Horizontal Cursors on a Waveform Turn off the cursors Using Vertical Cursors on a Waveform Making Rise Time Measurements Using Cursors on a A+B, A-B or A*B Waveform Triggering on Waveforms Screen with all Trigger Information Setting Trigger Level and Slope Trigger Delay or Pre-trigger View Using Trigger Delay or Pre-trigger Open the Trigger Options menu Automatic Trigger OptionsOpen the Automatic Trigger Reject Filter Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Select Free Run, jump to Noise Set Noise reject Filter to On Triggering on Noisy WaveformsMaking a Single Acquisition Select On Trigger, jump to Noise Making a Single Shot Measurement Select 1.2V under the Ext Level Triggering on External WaveformsLabel Triggering on Video Signals Triggering on Video Frames Enable video line selectionTriggering on Video Lines Detecting Narrow Pulses Triggering on PulsesSelect On Trigger Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing Pulses Triggering on Missing Pulses Saving and Recalling Using Memory, PC and Printer Saving Screens with Associated Setups Recalling Screens with Associated Setups Deleting Screens with Associated SetupsDisplay the SAVE/PRINT key labels Scroll through all stored screens Recalling a Setup Configuration Viewing Stored Screens Documenting Screens Connecting to a Computer Connecting a Serial Printer Connecting to a Printer Baud Rate Setting up the Printing ConfigurationOpen the Printer Setup submenu Printing a Screen Fluke 192/196/199 Tips Using the Standard Accessories Heavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test Probes Tips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Press and hold Using the Tilt StandSuppressing Key Labels and Menu’s Turn the test tool off Accept French as the language Adjusting the Contrast and BrightnessChanging the Information Language Open the Language Select Choose 04, jump to Day Open Date Adjust menuChanging Date and Time Choose 1999, jump to Month Setting the Power Down Timer Saving Battery Life Select Unchanged Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options To Coupling Maintaining the Test Tool Cleaning the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Open the User Options menu Extending Battery Operation Time Select Voltage, then jump to Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select 101, then return Maintaining the Test Tool Open the Version & Calibration Parts and AccessoriesStandard Accessories Displaying Calibration Information Ordering Code Standard Accessories TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not Function Introduction SpecificationsPerformance Characteristics Safety Characteristics Isolated Inputs a and B Vertical Dual Input OscilloscopeHorizontal Isolated External Trigger Trigger and DelayAutomatic Connect-and-View Trigger Edge Trigger Automatic Scope Measurements AC+DC Voltage True RMS AC Voltage VAC Duty Cycle Duty Amperes AMPPeak Frequency Hz Decibel dB PowerPhase Temperature Temp DMM Measurements on Meter Inputs Meter Diode With Optional Temperature Probe TrendPlot Meter or Scope RecorderScope Record Miscellaneous Zoom, Replay and Cursors Mechanical Probe CalibrationMemory Optical InterfacePort Environmental Max. Input Voltages SafetyMax. Floating Voltage Environmental SafetyElectrical specifications Probe 102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity 104 Numerics Index 106 107 108