Using Memory, PC and Printer, Saving and Recalling | Fluke 192, 199

Chapter 6

Using Memory, PC and Printer

About this Chapter

This chapter provides a step-by-step introduction to the general functions of the test tool that can be used in the three main modes: Scope, Meter, or Recorder. You will find information on printer and computer communication at the end of this chapter.

Saving and Recalling

You can:

•Save screens and setups to memory, and recall them again from memory. The test tool has 10 screen and setup memories and 2 record and setup memories.

•Recall screens and recordings to analyze or print the screen image at a later date.

•Recall a setup to continue a measurement with the recalled operating configuration.

57

Image 65

Fluke 192, 199, 196 user manual Using Memory, PC and Printer, Saving and Recalling

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using The Recorder Functions Using The MultimeterUsing Replay, Zoom and Cursors Fluke 192/196/199 Iii Index Specifications Manufacturer Declaration of ConformityStatement of Conformity Sample tests ScopeMeter Test Tool Kit Unpacking the Test Tool Kit # Description Description Safety Information Read First Safety Information Read First Impair the protection provided by the equipment If Safety Features are ImpairedUse of the test tool in a manner not specified may About this Chapter Using The ScopePowering the Test Tool Screen After Reset Resetting the Test Tool Open the Waveform Options Navigating a Menu Input Connections Hiding Key Labels and Menus Scope Connections Making Scope Connections Screen After an Auto Set Displaying an Unknown Signal with Connect-and-View Measurement Making Automatic Scope MeasurementsSelect the Peak-Peak Hz and V peak-peak as Scope Readings Freezing the Screen Jump to Waveform Using Average, Persistence and Glitch CaptureUsing Average for Smoothing Waveforms Persistence , then select Infinite Using Persistence to Display WaveformsJump to Waveform and Select Suppressing High Frequency Noise Displaying Glitches Reversing the Polarity of the Displayed Waveform Acquiring WaveformsSelecting AC-Coupling Select 10kHz HF reject to Mathematics... to open Analyzing WaveformsMathematics menu Or a vs B Making Meter Connections Using The Multimeter Measuring Resistance Values Making Multimeter Measurements Highlight a ac Making a Current MeasurementOpen the Current Probe Submenu Ampere Measurement Readings Selecting Auto/Manual Ranges Freezing the Readings Making a Relative Measurement Making Relative Measurements Opening the Recorder Main Menu Using The Recorder Functions Highlight Trend Plot Scope Plotting Measurements Over Time TrendPlotStarting a TrendPlot Function TrendPlot Reading Displaying Recorded Data Turning Off the TrendPlot Display Changing the Recorder OptionsOpen the Recorder Options Menu Highlight Scope Record Recording Scope Waveforms In Deep Memory Scope RecordStarting a Scope Record Function Using ScopeRecord in Single Sweep Mode Level Using Scope Record in Triggered Single Sweep ModeJump to Display Glitches Select Yes, then jump to Mode Triggered Single Sweep Recording Analyzing a TrendPlot or Scope Record Replaying the 100 Most Recent Scope Screens Using Replay, Zoom and Cursors Replaying a Waveform Replaying Step-by-Step Capturing 100 Intermittents Automatically Replaying ContinuouslyTurning Off the Replay Function Zooming in a Waveform Zooming in on a Waveform Turning Off the Zoom Function Displaying the Zoomed Waveform Making Cursor Measurements Using Horizontal Cursors on a Waveform Turn off the cursors Using Vertical Cursors on a Waveform Making Rise Time Measurements Using Cursors on a A+B, A-B or A*B Waveform Triggering on Waveforms Screen with all Trigger Information Setting Trigger Level and Slope Trigger Delay or Pre-trigger View Using Trigger Delay or Pre-trigger Open the Automatic Trigger Automatic Trigger OptionsOpen the Trigger Options menu Open the Trigger Options menu Open the Trigger on Edge menu Triggering on EdgesSelect Free Run, jump to Noise Reject Filter Making a Single Acquisition Triggering on Noisy WaveformsSelect On Trigger, jump to Noise Set Noise reject Filter to On Making a Single Shot Measurement Label Triggering on External WaveformsSelect 1.2V under the Ext Level Triggering on Video Signals Triggering on Video Lines Enable video line selectionTriggering on Video Frames Select On Trigger Triggering on PulsesDetecting Narrow Pulses Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing Pulses Triggering on Missing Pulses Saving and Recalling Using Memory, PC and Printer Saving Screens with Associated Setups Display the SAVE/PRINT key labels Deleting Screens with Associated SetupsRecalling Screens with Associated Setups Scroll through all stored screens Recalling a Setup Configuration Viewing Stored Screens Documenting Screens Connecting to a Computer Connecting a Serial Printer Connecting to a Printer Open the Printer Setup submenu Setting up the Printing ConfigurationPrinting a Screen Baud Rate Fluke 192/196/199 Tips Using the Standard Accessories Heavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test Probes Tips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Suppressing Key Labels and Menu’s Using the Tilt StandTurn the test tool off Press and hold Changing the Information Language Adjusting the Contrast and BrightnessOpen the Language Select Accept French as the language Changing Date and Time Open Date Adjust menuChoose 1999, jump to Month Choose 04, jump to Day Setting the Power Down Timer Saving Battery Life Changing the Auto Set Options Open the User Options menu Open the Auto Set Adjust MenuTo Coupling Select Unchanged Storing the Test Tool Cleaning the Test ToolMaintaining the Test Tool Charging the Batteries Charging the Batteries Open the User Options menu Extending Battery Operation Time Calibrating the Voltage Probes Replacing the NiMH Battery Pack BP190Select 101, then return Select Voltage, then jump to Maintaining the Test Tool Standard Accessories Parts and AccessoriesDisplaying Calibration Information Open the Version & Calibration Ordering Code Standard Accessories TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not Function Performance Characteristics SpecificationsSafety Characteristics Introduction Horizontal Dual Input OscilloscopeIsolated Inputs a and B Vertical Automatic Connect-and-View Trigger Trigger and DelayEdge Trigger Isolated External Trigger Automatic Scope Measurements AC+DC Voltage True RMS AC Voltage VAC Peak Amperes AMPFrequency Hz Duty Cycle Duty Phase PowerTemperature Temp Decibel dB DMM Measurements on Meter Inputs Meter Diode With Optional Temperature Probe Scope Record RecorderTrendPlot Meter or Scope Miscellaneous Zoom, Replay and Cursors Memory Probe CalibrationOptical InterfacePort Mechanical Environmental Max. Floating Voltage SafetyMax. Input Voltages Electrical specifications SafetyProbe Environmental 102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity 104 Numerics Index 106 107 108