Triggering on Video Signals | Fluke 192, 199, 196 guide

Triggering on Waveforms	5
Triggering on Video Signals

Triggering on Video Signals

To trigger on a video signal, first select the standard of the video signal you are going to measure:

1Apply a video signal to the red input A.

2

Display the TRIGGER key labels.

3

Open the Trigger Options menu.

Figure 30. Measuring Interlaced Video Signals

4						Select Video on A to open the
						Trigger on Video menu.
						Trigger on Video menu.

5						Select positive signal polarity for
						video signals with negative going
						video signals with negative going
						sync pulses.

6						Select the video standard and
						return.
						return.

Trigger level and slope are now fixed.

Observe that the key labels at the bottom of the screen have been changed to allow further selection of specific video trigger settings:

51

Image 59

Fluke 192, 199, 196 user manual Triggering on Video Signals, Open the Trigger Options menu

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Fluke 192/196/199 Using The MultimeterUsing The Recorder Functions Using Replay, Zoom and Cursors Iii Index Specifications Sample tests Declaration of ConformityManufacturer Statement of Conformity ScopeMeter Test Tool Kit Unpacking the Test Tool Kit # Description Description Safety Information Read First Safety Information Read First Impair the protection provided by the equipment If Safety Features are ImpairedUse of the test tool in a manner not specified may About this Chapter Using The ScopePowering the Test Tool Screen After Reset Resetting the Test Tool Open the Waveform Options Navigating a Menu Input Connections Hiding Key Labels and Menus Scope Connections Making Scope Connections Screen After an Auto Set Displaying an Unknown Signal with Connect-and-View Measurement Making Automatic Scope MeasurementsSelect the Peak-Peak Hz and V peak-peak as Scope Readings Freezing the Screen Jump to Waveform Using Average, Persistence and Glitch CaptureUsing Average for Smoothing Waveforms Persistence , then select Infinite Using Persistence to Display WaveformsJump to Waveform and Select Suppressing High Frequency Noise Displaying Glitches Reversing the Polarity of the Displayed Waveform Acquiring WaveformsSelecting AC-Coupling Select 10kHz HF reject to Or a vs B Analyzing WaveformsMathematics... to open Mathematics menu Making Meter Connections Using The Multimeter Measuring Resistance Values Making Multimeter Measurements Submenu Making a Current MeasurementHighlight a ac Open the Current Probe Ampere Measurement Readings Selecting Auto/Manual Ranges Freezing the Readings Making a Relative Measurement Making Relative Measurements Opening the Recorder Main Menu Using The Recorder Functions Highlight Trend Plot Scope Plotting Measurements Over Time TrendPlotStarting a TrendPlot Function TrendPlot Reading Displaying Recorded Data Menu Changing the Recorder OptionsTurning Off the TrendPlot Display Open the Recorder Options Highlight Scope Record Recording Scope Waveforms In Deep Memory Scope RecordStarting a Scope Record Function Using ScopeRecord in Single Sweep Mode Level Using Scope Record in Triggered Single Sweep ModeJump to Display Glitches Select Yes, then jump to Mode Triggered Single Sweep Recording Analyzing a TrendPlot or Scope Record Replaying the 100 Most Recent Scope Screens Using Replay, Zoom and Cursors Replaying a Waveform Replaying Step-by-Step Capturing 100 Intermittents Automatically Replaying ContinuouslyTurning Off the Replay Function Zooming in a Waveform Zooming in on a Waveform Turning Off the Zoom Function Displaying the Zoomed Waveform Making Cursor Measurements Using Horizontal Cursors on a Waveform Turn off the cursors Using Vertical Cursors on a Waveform Making Rise Time Measurements Using Cursors on a A+B, A-B or A*B Waveform Triggering on Waveforms Screen with all Trigger Information Setting Trigger Level and Slope Trigger Delay or Pre-trigger View Using Trigger Delay or Pre-trigger Open the Automatic Trigger Automatic Trigger OptionsOpen the Trigger Options menu Reject Filter Triggering on EdgesOpen the Trigger Options menu Open the Trigger on Edge menu Select Free Run, jump to Noise Set Noise reject Filter to On Triggering on Noisy WaveformsMaking a Single Acquisition Select On Trigger, jump to Noise Making a Single Shot Measurement Label Triggering on External WaveformsSelect 1.2V under the Ext Level Triggering on Video Signals Triggering on Video Lines Enable video line selectionTriggering on Video Frames Select On Trigger Triggering on PulsesDetecting Narrow Pulses Triggering on Narrow Glitches Open the Trigger Options menu Select On Trigger Finding Missing Pulses Triggering on Missing Pulses Saving and Recalling Using Memory, PC and Printer Saving Screens with Associated Setups Display the SAVE/PRINT key labels Deleting Screens with Associated SetupsRecalling Screens with Associated Setups Scroll through all stored screens Recalling a Setup Configuration Viewing Stored Screens Documenting Screens Connecting to a Computer Connecting a Serial Printer Connecting to a Printer Baud Rate Setting up the Printing ConfigurationOpen the Printer Setup submenu Printing a Screen Fluke 192/196/199 Tips Using the Standard Accessories Heavy Duty Fixed Connections for Scope Probing Using 2-mm Heavy Duty Test Probes Tips Using the Standard Accessories Measuring Using Independently Floating Isolated Inputs Using the Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Press and hold Using the Tilt StandSuppressing Key Labels and Menu’s Turn the test tool off Accept French as the language Adjusting the Contrast and BrightnessChanging the Information Language Open the Language Select Choose 04, jump to Day Open Date Adjust menuChanging Date and Time Choose 1999, jump to Month Setting the Power Down Timer Saving Battery Life Select Unchanged Open the User Options menu Open the Auto Set Adjust MenuChanging the Auto Set Options To Coupling Storing the Test Tool Cleaning the Test ToolMaintaining the Test Tool Charging the Batteries Charging the Batteries Open the User Options menu Extending Battery Operation Time Select Voltage, then jump to Replacing the NiMH Battery Pack BP190Calibrating the Voltage Probes Select 101, then return Maintaining the Test Tool Open the Version & Calibration Parts and AccessoriesStandard Accessories Displaying Calibration Information Ordering Code Standard Accessories TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting FlukeView Does Not Recognize The Test Tool Battery Operated Fluke Accessories Do Not Function Introduction SpecificationsPerformance Characteristics Safety Characteristics Horizontal Dual Input OscilloscopeIsolated Inputs a and B Vertical Isolated External Trigger Trigger and DelayAutomatic Connect-and-View Trigger Edge Trigger Automatic Scope Measurements AC+DC Voltage True RMS AC Voltage VAC Duty Cycle Duty Amperes AMPPeak Frequency Hz Decibel dB PowerPhase Temperature Temp DMM Measurements on Meter Inputs Meter Diode With Optional Temperature Probe Scope Record RecorderTrendPlot Meter or Scope Miscellaneous Zoom, Replay and Cursors Mechanical Probe CalibrationMemory Optical InterfacePort Environmental Max. Floating Voltage SafetyMax. Input Voltages Environmental SafetyElectrical specifications Probe 102 Disturbance less than 10% of full scale = 3V/m Electromagnetic Immunity 104 Numerics Index 106 107 108