Triggering on Video Frames, Triggering on Video Lines | Fluke 199

Fluke 192/196/199

Users Manual

Triggering on Video Frames

Use FIELD 1 or FIELD 2 to trigger either on the first half of the frame (odd) or on the second half of the frame (even).

To trigger on the second half of the frame, do the following:

7 Choose FIELD 2.

The signal part of the even field is displayed on the screen.

Triggering on Video Lines

Use ALL LINES to trigger on all line synchronization pulses (horizontal synchronization).

7 Choose ALL LINES.

The signal of one line is displayed on the screen. The screen is updated with the signal of the next line immediately after the test tool triggers on the horizontal synchronization pulse.

To view a specific video line in more detail, you can select the line number. For example, to measure on video line 123, continue from step 5 as follows:

7						Enable video line selection.
7						Enable video line selection.

8 Select number 123.

The signal of line 123 is displayed on the screen. Observe that the status line now also shows the selected line number. The screen is continuously updated with the signal of line 123.

52

Image 60

Fluke 199, 196, 192 user manual Triggering on Video Frames, Triggering on Video Lines, Enable video line selection

Contents

Fluke 192/196/199 Page Limited Warranty & Limitation of Liability Service Centers Table of Contents Using The Multimeter Using The Recorder FunctionsUsing Replay, Zoom and Cursors Fluke 192/196/199 Iii Specifications Index Declaration of Conformity ManufacturerStatement of Conformity Sample tests Unpacking the Test Tool Kit ScopeMeter Test Tool Kit Description # Description Safety Information Read First Safety Information Read First If Safety Features are Impaired Use of the test tool in a manner not specified mayImpair the protection provided by the equipment Using The Scope Powering the Test ToolAbout this Chapter Resetting the Test Tool Screen After Reset Navigating a Menu Open the Waveform Options Hiding Key Labels and Menus Input Connections Making Scope Connections Scope Connections Displaying an Unknown Signal with Connect-and-View Screen After an Auto Set Making Automatic Scope Measurements Select the Peak-PeakMeasurement Freezing the Screen Hz and V peak-peak as Scope Readings Using Average, Persistence and Glitch Capture Using Average for Smoothing WaveformsJump to Waveform Using Persistence to Display Waveforms Jump to Waveform and SelectPersistence , then select Infinite Displaying Glitches Suppressing High Frequency Noise Acquiring Waveforms Selecting AC-CouplingReversing the Polarity of the Displayed Waveform Select 10kHz HF reject to Analyzing Waveforms Mathematics... to openMathematics menu Or a vs B Using The Multimeter Making Meter Connections Making Multimeter Measurements Measuring Resistance Values Making a Current Measurement Highlight a acOpen the Current Probe Submenu Ampere Measurement Readings Freezing the Readings Selecting Auto/Manual Ranges Making Relative Measurements Making a Relative Measurement Using The Recorder Functions Opening the Recorder Main Menu Plotting Measurements Over Time TrendPlot Starting a TrendPlot FunctionHighlight Trend Plot Scope Displaying Recorded Data TrendPlot Reading Changing the Recorder Options Turning Off the TrendPlot DisplayOpen the Recorder Options Menu Recording Scope Waveforms In Deep Memory Scope Record Starting a Scope Record FunctionHighlight Scope Record Using ScopeRecord in Single Sweep Mode Using Scope Record in Triggered Single Sweep Mode Jump to Display Glitches Select Yes, then jump to ModeLevel Analyzing a TrendPlot or Scope Record Triggered Single Sweep Recording Using Replay, Zoom and Cursors Replaying the 100 Most Recent Scope Screens Replaying Step-by-Step Replaying a Waveform Replaying Continuously Turning Off the Replay FunctionCapturing 100 Intermittents Automatically Zooming in on a Waveform Zooming in a Waveform Displaying the Zoomed Waveform Turning Off the Zoom Function Using Horizontal Cursors on a Waveform Making Cursor Measurements Using Vertical Cursors on a Waveform Turn off the cursors Using Cursors on a A+B, A-B or A*B Waveform Making Rise Time Measurements Triggering on Waveforms Setting Trigger Level and Slope Screen with all Trigger Information Using Trigger Delay or Pre-trigger Trigger Delay or Pre-trigger View Automatic Trigger Options Open the Trigger Options menuOpen the Automatic Trigger Triggering on Edges Open the Trigger Options menu Open the Trigger on Edge menuSelect Free Run, jump to Noise Reject Filter Triggering on Noisy Waveforms Making a Single AcquisitionSelect On Trigger, jump to Noise Set Noise reject Filter to On Making a Single Shot Measurement Triggering on External Waveforms Select 1.2V under the Ext LevelLabel Triggering on Video Signals Enable video line selection Triggering on Video FramesTriggering on Video Lines Triggering on Pulses Detecting Narrow PulsesSelect On Trigger Triggering on Narrow Glitches Finding Missing Pulses Open the Trigger Options menu Select On Trigger Triggering on Missing Pulses Using Memory, PC and Printer Saving and Recalling Saving Screens with Associated Setups Deleting Screens with Associated Setups Recalling Screens with Associated SetupsDisplay the SAVE/PRINT key labels Recalling a Setup Configuration Viewing Stored Screens Scroll through all stored screens Connecting to a Computer Documenting Screens Connecting to a Printer Connecting a Serial Printer Setting up the Printing Configuration Open the Printer Setup submenuPrinting a Screen Baud Rate Fluke 192/196/199 Using the Standard Accessories Tips Probing Using 2-mm Heavy Duty Test Probes Heavy Duty Fixed Connections for Scope Tips Using the Standard Accessories Using the Independently Floating Isolated Inputs Measuring Using Independently Floating Isolated Inputs Tips Using the Independently Floating Isolated Inputs Using the Tilt Stand Suppressing Key Labels and Menu’sTurn the test tool off Press and hold Adjusting the Contrast and Brightness Changing the Information LanguageOpen the Language Select Accept French as the language Open Date Adjust menu Changing Date and TimeChoose 1999, jump to Month Choose 04, jump to Day Saving Battery Life Setting the Power Down Timer Open the User Options menu Open the Auto Set Adjust Menu Changing the Auto Set OptionsTo Coupling Select Unchanged Cleaning the Test Tool Maintaining the Test ToolStoring the Test Tool Charging the Batteries Charging the Batteries Extending Battery Operation Time Open the User Options menu Replacing the NiMH Battery Pack BP190 Calibrating the Voltage ProbesSelect 101, then return Select Voltage, then jump to Maintaining the Test Tool Parts and Accessories Standard AccessoriesDisplaying Calibration Information Open the Version & Calibration Standard Accessories Ordering Code TL24 General Purpose Leads RS200 Optional Accessories Troubleshooting Battery Operated Fluke Accessories Do Not Function FlukeView Does Not Recognize The Test Tool Specifications Performance CharacteristicsSafety Characteristics Introduction Dual Input Oscilloscope Isolated Inputs a and B VerticalHorizontal Trigger and Delay Automatic Connect-and-View TriggerEdge Trigger Isolated External Trigger Automatic Scope Measurements AC Voltage VAC AC+DC Voltage True RMS Amperes AMP PeakFrequency Hz Duty Cycle Duty Power PhaseTemperature Temp Decibel dB Meter DMM Measurements on Meter Inputs With Optional Temperature Probe Diode Recorder TrendPlot Meter or ScopeScope Record Zoom, Replay and Cursors Miscellaneous Probe Calibration MemoryOptical InterfacePort Mechanical Environmental Safety Max. Input VoltagesMax. Floating Voltage Safety Electrical specificationsProbe Environmental 102 Electromagnetic Immunity Disturbance less than 10% of full scale = 3V/m 104 Index Numerics 106 107 108